On Sun, Mar 27, 2022 at 09:04:46AM +0200, Aleksa Savic wrote:
> Extend aquacomputer_d5next driver to expose hardware temperature sensors
> and fans of the Aquacomputer Octo fan controller, which communicates
> through a proprietary USB HID protocol.
>
> Four temperature sensors and eight PWM controllable fans are available.
> Additionally, serial number, firmware version and power-on count are
> exposed through debugfs.
>
> This driver has been tested on x86_64.
>
> Signed-off-by: Aleksa Savic <savicaleksa83@xxxxxxxxx>
> ---
> Changes in v3:
> - Added break; statements where needed
> - aqc_set_ctrl_val() now only sets values with a length of 2
> - Replace goto with return in aqc_send_ctrl_data()
>
> Changes in v2:
> - Fixed formatting
> - HID report values from device are now being converted sooner
> - aqc_pwm_to_percent() is now range checked
> - Put pointers to labels in aqc_data
> - Simplified checksum calculation call
> ---
> Documentation/hwmon/aquacomputer_d5next.rst | 4 +
> drivers/hwmon/Kconfig | 7 +-
> drivers/hwmon/aquacomputer_d5next.c | 431 +++++++++++++++++---
> 3 files changed, 390 insertions(+), 52 deletions(-)
>
> diff --git a/Documentation/hwmon/aquacomputer_d5next.rst b/Documentation/hwmon/aquacomputer_d5next.rst
> index 3373e27b707d..e69f718caf5b 100644
> --- a/Documentation/hwmon/aquacomputer_d5next.rst
> +++ b/Documentation/hwmon/aquacomputer_d5next.rst
> @@ -7,6 +7,7 @@ Supported devices:
>
> * Aquacomputer D5 Next watercooling pump
> * Aquacomputer Farbwerk 360 RGB controller
> +* Aquacomputer Octo fan controller
>
> Author: Aleksa Savic
>
> @@ -28,6 +29,9 @@ seems to require sending it a complete configuration. That includes addressable
> RGB LEDs, for which there is no standard sysfs interface. Thus, that task is
> better suited for userspace tools.
>
> +The Octo exposes four temperature sensors and eight PWM controllable fans, along
> +with their speed (in RPM), power, voltage and current.
> +
> The Farbwerk 360 exposes four temperature sensors. Depending on the device,
> not all sysfs and debugfs entries will be available.
>
> diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
> index db8bc55e5f50..5beadd8a0932 100644
> --- a/drivers/hwmon/Kconfig
> +++ b/drivers/hwmon/Kconfig
> @@ -256,11 +256,12 @@ config SENSORS_AHT10
> will be called aht10.
>
> config SENSORS_AQUACOMPUTER_D5NEXT
> - tristate "Aquacomputer D5 Next watercooling pump"
> + tristate "Aquacomputer D5 Next, Octo and Farbwerk 360"
> depends on USB_HID
> help
> - If you say yes here you get support for the Aquacomputer D5 Next
> - watercooling pump sensors.
> + If you say yes here you get support for sensors and fans of
> + the Aquacomputer D5 Next watercooling pump, Octo fan
> + controller and Farbwerk 360 RGB controller, where available.
>
> This driver can also be built as a module. If so, the module
> will be called aquacomputer_d5next.
> diff --git a/drivers/hwmon/aquacomputer_d5next.c b/drivers/hwmon/aquacomputer_d5next.c
> index 525809cf7c95..cd008bfa03be 100644
> --- a/drivers/hwmon/aquacomputer_d5next.c
> +++ b/drivers/hwmon/aquacomputer_d5next.c
> @@ -1,6 +1,6 @@
> // SPDX-License-Identifier: GPL-2.0+
> /*
> - * hwmon driver for Aquacomputer devices (D5 Next, Farbwerk 360)
> + * hwmon driver for Aquacomputer devices (D5 Next, Farbwerk 360, Octo)
> *
> * Aquacomputer devices send HID reports (with ID 0x01) every second to report
> * sensor values.
> @@ -8,23 +8,27 @@
> * Copyright 2021 Aleksa Savic <savicaleksa83@xxxxxxxxx>
> */
>
> +#include <linux/crc16.h>
> #include <linux/debugfs.h>
> #include <linux/hid.h>
> #include <linux/hwmon.h>
> #include <linux/jiffies.h>
> #include <linux/module.h>
> +#include <linux/mutex.h>
> #include <linux/seq_file.h>
> #include <asm/unaligned.h>
>
> #define USB_VENDOR_ID_AQUACOMPUTER 0x0c70
> #define USB_PRODUCT_ID_D5NEXT 0xf00e
> #define USB_PRODUCT_ID_FARBWERK360 0xf010
> +#define USB_PRODUCT_ID_OCTO 0xf011
>
> -enum kinds { d5next, farbwerk360 };
> +enum kinds { d5next, farbwerk360, octo };
>
> static const char *const aqc_device_names[] = {
> [d5next] = "d5next",
> - [farbwerk360] = "farbwerk360"
> + [farbwerk360] = "farbwerk360",
> + [octo] = "octo"
> };
>
> #define DRIVER_NAME "aquacomputer_d5next"
> @@ -35,6 +39,18 @@ static const char *const aqc_device_names[] = {
> #define SERIAL_SECOND_PART 5
> #define FIRMWARE_VERSION 13
>
> +#define CTRL_REPORT_ID 0x03
> +
> +/* The HID report that the official software always sends
> + * after writing values, currently same for all devices
> + */
> +#define SECONDARY_CTRL_REPORT_ID 0x02
> +#define SECONDARY_CTRL_REPORT_SIZE 0x0B
> +
> +static u8 secondary_ctrl_report[] = {
> + 0x02, 0x00, 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00, 0x34, 0xC6
> +};
> +
> /* Register offsets for the D5 Next pump */
> #define D5NEXT_POWER_CYCLES 24
>
> @@ -55,12 +71,38 @@ static const char *const aqc_device_names[] = {
>
> /* Register offsets for the Farbwerk 360 RGB controller */
> #define FARBWERK360_NUM_SENSORS 4
> -#define FARBWERK360_SENSOR_START 0x32
> +#define FARBWERK360_SENSOR_START 0x32
> #define FARBWERK360_SENSOR_SIZE 0x02
> #define FARBWERK360_SENSOR_DISCONNECTED 0x7FFF
>
> +/* Register offsets for the Octo fan controller */
> +#define OCTO_POWER_CYCLES 0x18
> +#define OCTO_NUM_FANS 8
> +#define OCTO_FAN_PERCENT_OFFSET 0x00
> +#define OCTO_FAN_VOLTAGE_OFFSET 0x02
> +#define OCTO_FAN_CURRENT_OFFSET 0x04
> +#define OCTO_FAN_POWER_OFFSET 0x06
> +#define OCTO_FAN_SPEED_OFFSET 0x08
> +
> +static u8 octo_sensor_fan_offsets[] = { 0x7D, 0x8A, 0x97, 0xA4, 0xB1, 0xBE, 0xCB, 0xD8 };
> +
> +#define OCTO_NUM_SENSORS 4
> +#define OCTO_SENSOR_START 0x3D
> +#define OCTO_SENSOR_SIZE 0x02
> +#define OCTO_SENSOR_DISCONNECTED 0x7FFF
> +
> +#define OCTO_CTRL_REPORT_SIZE 0x65F
> +#define OCTO_CTRL_REPORT_CHECKSUM_OFFSET 0x65D
> +#define OCTO_CTRL_REPORT_CHECKSUM_START 0x01
> +#define OCTO_CTRL_REPORT_CHECKSUM_LENGTH 0x65C
> +
> +/* Fan speed registers in Octo control report (from 0-100%) */
> +static u16 octo_ctrl_fan_offsets[] = { 0x5B, 0xB0, 0x105, 0x15A, 0x1AF, 0x204, 0x259, 0x2AE };
> +
> /* Labels for D5 Next */
> -#define L_D5NEXT_COOLANT_TEMP "Coolant temp"
> +static const char *const label_d5next_temp[] = {
> + "Coolant temp"
> +};
>
> static const char *const label_d5next_speeds[] = {
> "Pump speed",
> @@ -83,7 +125,7 @@ static const char *const label_d5next_current[] = {
> "Fan current"
> };
>
> -/* Labels for Farbwerk 360 temperature sensors */
> +/* Labels for Farbwerk 360 and Octo temperature sensors */
> static const char *const label_temp_sensors[] = {
> "Sensor 1",
> "Sensor 2",
> @@ -91,32 +133,180 @@ static const char *const label_temp_sensors[] = {
> "Sensor 4"
> };
>
> +/* Labels for Octo */
> +static const char *const label_fan_speed[] = {
> + "Fan 1 speed",
> + "Fan 2 speed",
> + "Fan 3 speed",
> + "Fan 4 speed",
> + "Fan 5 speed",
> + "Fan 6 speed",
> + "Fan 7 speed",
> + "Fan 8 speed"
> +};
> +
> +static const char *const label_fan_power[] = {
> + "Fan 1 power",
> + "Fan 2 power",
> + "Fan 3 power",
> + "Fan 4 power",
> + "Fan 5 power",
> + "Fan 6 power",
> + "Fan 7 power",
> + "Fan 8 power"
> +};
> +
> +static const char *const label_fan_voltage[] = {
> + "Fan 1 voltage",
> + "Fan 2 voltage",
> + "Fan 3 voltage",
> + "Fan 4 voltage",
> + "Fan 5 voltage",
> + "Fan 6 voltage",
> + "Fan 7 voltage",
> + "Fan 8 voltage"
> +};
> +
> +static const char *const label_fan_current[] = {
> + "Fan 1 current",
> + "Fan 2 current",
> + "Fan 3 current",
> + "Fan 4 current",
> + "Fan 5 current",
> + "Fan 6 current",
> + "Fan 7 current",
> + "Fan 8 current"
> +};
> +
> struct aqc_data {
> struct hid_device *hdev;
> struct device *hwmon_dev;
> struct dentry *debugfs;
> + struct mutex mutex; /* Used for locking access when reading and writing PWM values */
> enum kinds kind;
> const char *name;
>
> + int buffer_size;
> + u8 *buffer;
> + int checksum_start;
> + int checksum_length;
> + int checksum_offset;
> +
> /* General info, same across all devices */
> u32 serial_number[2];
> u16 firmware_version;
>
> - /* D5 Next specific - how many times the device was powered on */
> + /* How many times the device was powered on */
> u32 power_cycles;
>
> /* Sensor values */
> s32 temp_input[4];
> - u16 speed_input[2];
> - u32 power_input[2];
> - u16 voltage_input[3];
> - u16 current_input[2];
> + u16 speed_input[8];
> + u32 power_input[8];
> + u16 voltage_input[8];
> + u16 current_input[8];
> +
> + /* Label values */
> + const char *const *temp_label;
> + const char *const *speed_label;
> + const char *const *power_label;
> + const char *const *voltage_label;
> + const char *const *current_label;
>
> unsigned long updated;
> };
>
> -static umode_t aqc_is_visible(const void *data, enum hwmon_sensor_types type, u32 attr,
> - int channel)
> +static int aqc_percent_to_pwm(u16 val)
I am sure I asked this before. The calculation looks like a conversion
from centi-percent to pwm, not from percent to pwm. Please either reflect
that in the function name or add a comment.
Thanks,
Guenter
