On 05/30/2013 03:35 PM, Dan Murphy wrote:
Fix spelling in my own comments
On 05/30/2013 03:31 PM, Dan Murphy wrote:
On 05/30/2013 03:14 PM, Ruchika Kharwar wrote:
This patch adds an optional parameter "dr_mode" to the dwc3 core device node.
In the case the compile flag for the DWC3 controller is set to
"USB_DWC3_DUAL_ROLE" a device tree could restrain to either functionality of
host or gadget. In the case the device tree does not use this optional flag or
specifies it superfluously to "drd" the functionality will be that
of a dual role device.
Signed-off-by: Ruchika Kharwar <ruchika@xxxxxx>
---
Can you add patch history if this is truly a new patch to a previous submission
Will do in the next pach submitted.
Documentation/devicetree/bindings/usb/dwc3.txt | 3 ++-
drivers/usb/dwc3/core.c | 21 +++++++++++++++++----
2 files changed, 19 insertions(+), 5 deletions(-)
diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt
index 7a95c65..2f5d584 100644
--- a/Documentation/devicetree/bindings/usb/dwc3.txt
+++ b/Documentation/devicetree/bindings/usb/dwc3.txt
@@ -10,7 +10,8 @@ Required properties:
Optional properties:
- tx-fifo-resize: determines if the FIFO *has* to be reallocated.
-
+ - dr_mode: determines the mode of core. Supported modes are "gadget", "host"
+ and "drd".
My previous comments still stand for this section. Nothing was addressed or commented back
https://patchwork.kernel.org/patch/2638511/
This is usually a subnode to DWC3 glue to which it is connected.
dwc3@4a030000 {
diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
index c35d49d..e11660a 100644
--- a/drivers/usb/dwc3/core.c
+++ b/drivers/usb/dwc3/core.c
@@ -378,7 +378,7 @@ static int dwc3_probe(struct platform_device *pdev)
void *mem;
u8 mode;
-
+ char *dr_mode;
mem = devm_kzalloc(dev, sizeof(*dwc) + DWC3_ALIGN_MASK, GFP_KERNEL);
if (!mem) {
dev_err(dev, "not enough memory\n");
@@ -520,9 +520,22 @@ static int dwc3_probe(struct platform_device *pdev)
mode = DWC3_MODE_HOST;
else if (IS_ENABLED(CONFIG_USB_DWC3_GADGET))
mode = DWC3_MODE_DEVICE;
- else
- mode = DWC3_MODE_DRD;
-
+ else {
+ if (of_property_read_string(node, "dr_mode", &dr_mode))
+ mode = DWC3_MODE_DRD;
+ else {
+ if (strcmp(dr_mode, "host") == 0)
+ mode = DWC3_MODE_HOST;
+ else if (strcmp(dr_mode, "gadget") == 0)
+ mode = DWC3_MODE_DEVICE;
+ else if (strcmp(dr_mode, "drd") == 0)
+ mode = DWC3_MODE_DRD;
My previous comments still stand for this section. Nothing was addressed or commented back
https://patchwork.kernel.org/patch/2638511/
DRD mode is the super set mode for Host and Gadget. The compile
time flag is primary. If DRD is set, the host and gadget code is
compiled in.
The dr_mode property can be used *if* specified in the device
tree. A specific example may be a board could have constraints where the
port could only be a host
or gadget. In that case, the dr_mode property is specified
overrides the compile flag.
+ else {
+ dev_err(dev, "invalid dr_mode property value\n");
+ goto err2;
This is still wrong. You have not initialized and of the device's
s/and/any
This is correct as per 3.10-rc3. If you're looking at an older
tree you'd be right.
+ }
+ }
+ }
switch (mode) {
case DWC3_MODE_DEVICE:
dwc3_set_mode(dwc, DWC3_GCTL_PRTCAP_DEVICE);
Is this a new patch?
Subject should say v2.
Yes, my bad.. learning.. next patch will have it.
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
