Re: [RFC 1/8] serial:st-asc: Add ST ASC driver.

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 16:34 Wed 08 May     , Arnd Bergmann wrote:
> On Wednesday 08 May 2013, Srinivas KANDAGATLA wrote:
> > From: Srinivas Kandagatla <srinivas.kandagatla@xxxxxx>
> 
> > +*st-asc(Serial Port)
> > +
> > +Required properties:
> > +- compatible : Should be "st,asc".
> 
> Are there any hardware revision numbers for the asc? If there are potentially
> incompatible or backwards-compatible variants, it would be good to include
> the version in this string.

The st,asc come from st20 or st200 IIRC which was not ARM but a ST arch
and then used on st40 series

an the st,asc for st200 and st40 are not compatible completly
> 
> > +- reg, reg-names, interrupts, interrupt-names	: Standard way to define device
> > +			resources with names. look in
> > +			Documentation/devicetree/bindings/resource-names.txt
> > +
> > +Optional properties:
> > +- st,hw-flow-ctrl	bool flag to enable hardware flow control.
> > +- st,force-m1		bool flat to force asc to be in Mode-1 recommeded
> > +			for high bit rates (above 19.2K)
> > +Example:
> > +serial@fe440000{
> > +    compatible    = "st,asc";
> > +    reg         = <0xfe440000 0x2c>;
> > +    interrupts     =  <0 209 0>;
> > +};
> 
> I would also recommed adding a way to set the default baud rate through
> a property. Following the example of the 8250 driver, you should probably
> call that "current-speed".
on st it has always be 38k

> 
> > diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
> > index 7e7006f..346f325 100644
> > --- a/drivers/tty/serial/Kconfig
> > +++ b/drivers/tty/serial/Kconfig
> > @@ -1484,6 +1484,25 @@ config SERIAL_RP2_NR_UARTS
> >  	  If multiple cards are present, the default limit of 32 ports may
> >  	  need to be increased.
> >  
> > +config SERIAL_ST_ASC
> > +	tristate "ST ASC serial port support"
> > +	depends on PLAT_STIXXXX
> > +	default y
> > +	select SERIAL_CORE
> > +	help
> > +	  This driver is for the on-chip Asychronous Serial Controller on
> > +	  STMicroelectronics STixxxx SoCs.
> > +	  ASC is embedded in ST COMMS IP block. It supports Rx & Tx functionality.
> > +	  It support all industry standard baud rates.
> > +
> > +	  If unsure, say N.
> 
> I would not make it "default y".
me too
> 
> > +config SERIAL_ST_ASC_CONSOLE
> > +	bool "Support for console on ST ASC"
> > +	depends on SERIAL_ST_ASC
> > +	default y
> > +	select SERIAL_CORE_CONSOLE
> > +
> >  endmenu
> 
> This needs to be "depends on SERIAL_ST_ASC=y". You would get a link error
> if you try to make SERIAL_ST_ASC a loadable module and SERIAL_ST_ASC_CONSOLE
> built-in.
> 
> > +
> > +static struct asc_port asc_ports[ASC_MAX_PORTS];
> > +static struct uart_driver asc_uart_driver;
> > +
> > +/*---- Forward function declarations---------------------------*/
> > +static irqreturn_t asc_interrupt(int irq, void *ptr);
> > +static void asc_transmit_chars(struct uart_port *);
> > +static int asc_set_baud(struct asc_port *ascport, int baud);
> > +
> 
> Please remove all forward declarations, by reordering the functions in
> the way they are called.
> 
and drop the dummy functions
> 
> > diff --git a/drivers/tty/serial/st-asc.h b/drivers/tty/serial/st-asc.h
> > new file mode 100644
> > index 0000000..e59f818
> > --- /dev/null
> > +++ b/drivers/tty/serial/st-asc.h
> > +#ifndef _ST_ASC_H
> > +#define _ST_ASC_H
> > +
> > +#include <linux/serial_core.h>
> > +#include <linux/clk.h>
> > +
> > +struct asc_port {
> > +	struct uart_port port;
> > +	struct clk *clk;
> > +	unsigned int hw_flow_control:1;
> > +	unsigned int check_parity:1;
> > +	unsigned int force_m1:1;
> > +};
> 
> Since this header file is only used in one place, just merge it into
> the driver itself.
> 
> > +#define ASC_MAJOR		204
> > +#define ASC_MINOR_START		40
> 
> I don't know what the current policy is on allocating major/minor numbers,
> but I'm sure you cannot just reuse one that is already used.
> 
> Documentation/devices.txt lists the ones that are officially assigned.
> Can't you use dynamic allocation here?
> 
> 	Arnd
> _______________________________________________
> devicetree-discuss mailing list
> devicetree-discuss@xxxxxxxxxxxxxxxx
> https://lists.ozlabs.org/listinfo/devicetree-discuss
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux FS]     [Yosemite Forum]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux