Re: [PATCH 4/4] drivers: usb: start using the control module driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Friday 18 January 2013 05:32 PM, Felipe Balbi wrote:
Hi,

On Fri, Jan 18, 2013 at 03:10:45PM +0530, Kishon Vijay Abraham I wrote:
Start using the control module driver for powering on the PHY and for
writing to the mailbox instead of writing to the control module
registers on their own.

Signed-off-by: Kishon Vijay Abraham I <kishon@xxxxxx>
---
  Documentation/devicetree/bindings/usb/omap-usb.txt |    4 ++
  Documentation/devicetree/bindings/usb/usb-phy.txt  |    7 +--
  arch/arm/mach-omap2/omap_hwmod_44xx_data.c         |   13 ----
  drivers/usb/musb/Kconfig                           |    1 +
  drivers/usb/musb/omap2430.c                        |   64 ++++++++------------
  drivers/usb/musb/omap2430.h                        |    9 ---
  drivers/usb/phy/Kconfig                            |    1 +
  drivers/usb/phy/omap-usb2.c                        |   38 +++---------
  include/linux/usb/omap_usb.h                       |    4 +-
  9 files changed, 42 insertions(+), 99 deletions(-)

diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt
index ead6ba9..8bedbba 100644
--- a/Documentation/devicetree/bindings/usb/omap-usb.txt
+++ b/Documentation/devicetree/bindings/usb/omap-usb.txt
@@ -3,6 +3,9 @@ OMAP GLUE AND OTHER OMAP SPECIFIC COMPONENTS
  OMAP MUSB GLUE
   - compatible : Should be "ti,omap4-musb" or "ti,omap3-musb"
   - ti,hwmods : must be "usb_otg_hs"
+ - ti,has_mailbox : to specify that omap uses an external mailbox
+   (in control module) to communicate with the musb core during device connect
+   and disconnect.
   - multipoint : Should be "1" indicating the musb controller supports
     multipoint. This is a MUSB configuration-specific setting.
   - num_eps : Specifies the number of endpoints. This is also a
@@ -24,6 +27,7 @@ SOC specific device node entry
  usb_otg_hs: usb_otg_hs@4a0ab000 {
  	compatible = "ti,omap4-musb";
  	ti,hwmods = "usb_otg_hs";
+	ti,has_mailbox;
  	multipoint = <1>;
  	num_eps = <16>;
  	ram_bits = <12>;
diff --git a/Documentation/devicetree/bindings/usb/usb-phy.txt b/Documentation/devicetree/bindings/usb/usb-phy.txt
index 2466b6f..48761a2 100644
--- a/Documentation/devicetree/bindings/usb/usb-phy.txt
+++ b/Documentation/devicetree/bindings/usb/usb-phy.txt
@@ -4,9 +4,7 @@ OMAP USB2 PHY

  Required properties:
   - compatible: Should be "ti,omap-usb2"
- - reg : Address and length of the register set for the device. Also
-add the address of control module dev conf register until a driver for
-control module is added
+ - reg : Address and length of the register set for the device.

  Optional properties:
   - ctrl_module : phandle of the control module used by PHY driver to power on
@@ -16,7 +14,6 @@ This is usually a subnode of ocp2scp to which it is connected.

  usb2phy@4a0ad080 {
  	compatible = "ti,omap-usb2";
-	reg = <0x4a0ad080 0x58>,
-	      <0x4a002300 0x4>;
+	reg = <0x4a0ad080 0x58>;
  	ctrl_module = <&omap_control_usb>;
  };
diff --git a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
index 129d508..103f4ba 100644
--- a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
@@ -2698,13 +2698,6 @@ static struct resource omap44xx_usb_phy_and_pll_addrs[] = {
  		.end		= 0x4a0ae000,
  		.flags		= IORESOURCE_MEM,
  	},
-	{
-		/* XXX: Remove this once control module driver is in place */
-		.name		= "ctrl_dev",
-		.start		= 0x4a002300,
-		.end		= 0x4a002303,
-		.flags		= IORESOURCE_MEM,
-	},
  	{ }
  };

@@ -6152,12 +6145,6 @@ static struct omap_hwmod_addr_space omap44xx_usb_otg_hs_addrs[] = {
  		.pa_end		= 0x4a0ab7ff,
  		.flags		= ADDR_TYPE_RT
  	},
-	{
-		/* XXX: Remove this once control module driver is in place */
-		.pa_start	= 0x4a00233c,
-		.pa_end		= 0x4a00233f,
-		.flags		= ADDR_TYPE_RT
-	},
  	{ }
  };

diff --git a/drivers/usb/musb/Kconfig b/drivers/usb/musb/Kconfig
index 23a0b7f..de6e5ce 100644
--- a/drivers/usb/musb/Kconfig
+++ b/drivers/usb/musb/Kconfig
@@ -11,6 +11,7 @@ config USB_MUSB_HDRC
  	select NOP_USB_XCEIV if (SOC_TI81XX || SOC_AM33XX)
  	select TWL4030_USB if MACH_OMAP_3430SDP
  	select TWL6030_USB if MACH_OMAP_4430SDP || MACH_OMAP4_PANDA
+	select OMAP_CONTROL_USB if MACH_OMAP_4430SDP || MACH_OMAP4_PANDA
  	select USB_OTG_UTILS
  	help
  	  Say Y here if your system has a dual role high speed USB
diff --git a/drivers/usb/musb/omap2430.c b/drivers/usb/musb/omap2430.c
index da00af4..3e7ceef 100644
--- a/drivers/usb/musb/omap2430.c
+++ b/drivers/usb/musb/omap2430.c
@@ -37,6 +37,7 @@
  #include <linux/err.h>
  #include <linux/delay.h>
  #include <linux/usb/musb-omap.h>
+#include <linux/usb/omap_control_usb.h>

  #include "musb_core.h"
  #include "omap2430.h"
@@ -46,7 +47,7 @@ struct omap2430_glue {
  	struct platform_device	*musb;
  	enum omap_musb_vbus_id_status status;
  	struct work_struct	omap_musb_mailbox_work;
-	u32 __iomem		*control_otghs;
+	struct device		*control_otghs;
  };
  #define glue_to_musb(g)		platform_get_drvdata(g->musb)

@@ -54,26 +55,6 @@ struct omap2430_glue		*_glue;

  static struct timer_list musb_idle_timer;

-/**
- * omap4_usb_phy_mailbox - write to usb otg mailbox
- * @glue: struct omap2430_glue *
- * @val: the value to be written to the mailbox
- *
- * On detection of a device (ID pin is grounded), this API should be called
- * to set AVALID, VBUSVALID and ID pin is grounded.
- *
- * When OMAP is connected to a host (OMAP in device mode), this API
- * is called to set AVALID, VBUSVALID and ID pin in high impedance.
- *
- * XXX: This function will be removed once we have a seperate driver for
- * control module
- */
-static void omap4_usb_phy_mailbox(struct omap2430_glue *glue, u32 val)
-{
-	if (glue->control_otghs)
-		writel(val, glue->control_otghs);
-}
-
  static void musb_do_idle(unsigned long _musb)
  {
  	struct musb	*musb = (void *)_musb;
@@ -269,7 +250,6 @@ EXPORT_SYMBOL_GPL(omap_musb_mailbox);

  static void omap_musb_set_mailbox(struct omap2430_glue *glue)
  {
-	u32 val;
  	struct musb *musb = glue_to_musb(glue);
  	struct device *dev = musb->controller;
  	struct musb_hdrc_platform_data *pdata = dev->platform_data;
@@ -285,8 +265,8 @@ static void omap_musb_set_mailbox(struct omap2430_glue *glue)
  		musb->xceiv->last_event = USB_EVENT_ID;
  		if (musb->gadget_driver) {
  			pm_runtime_get_sync(dev);
-			val = AVALID | VBUSVALID;
-			omap4_usb_phy_mailbox(glue, val);
+			if (!IS_ERR(glue->control_otghs))
+				omap_control_usb_host_mode(glue->control_otghs);

you could introduce a helper to do the checks for you. something like:

static inline void omap_control_set_mode(*ctrl, int mode)
{
	if (IS_ERR(glue->control_otghs))
		return;

	switch (mode) {
	case HOST:
		omap_control_usb_host_mode(ctrl);
		break;
	case DEVICE:
		omap_control_usb_device(ctrl)
		break;
	default:
		meh();
	}
}

likewise for power() method

Ok.

Thanks
Kishon
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html


[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux FS]     [Yosemite Forum]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux