On 11/02/2012 11:21 AM, Murali Karicheri wrote:
> This is a platform driver for asynchronous external memory interface
> available on TI SoCs. This driver was previously located inside the
> mach-davinci folder. As this DaVinci IP is re-used across multiple
> family of devices such as c6x, keystone etc, the driver is moved to drivers.
> The driver configures async bus parameters associated with a particular
> chip select. For DaVinci controller driver and driver for other async
> devices such as NOR flash, ASRAM etc, the bus confuguration is
> done by this driver at init time. A set of APIs (set/get) provided to
> update the values based on specific driver usage.
>
> Signed-off-by: Murali Karicheri <m-karicheri2@xxxxxx>
> ---
> .../devicetree/bindings/arm/davinci/aemif.txt | 62 +++
> drivers/memory/Kconfig | 10 +
> drivers/memory/Makefile | 1 +
> drivers/memory/davinci-aemif.c | 397 ++++++++++++++++++++
> include/linux/platform_data/davinci-aemif.h | 47 +++
> 5 files changed, 517 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/arm/davinci/aemif.txt
> create mode 100644 drivers/memory/davinci-aemif.c
> create mode 100644 include/linux/platform_data/davinci-aemif.h
>
> diff --git a/Documentation/devicetree/bindings/arm/davinci/aemif.txt b/Documentation/devicetree/bindings/arm/davinci/aemif.txt
> new file mode 100644
> index 0000000..7d70d42
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/arm/davinci/aemif.txt
> @@ -0,0 +1,62 @@
> +* Texas Instruments Davinci AEMIF bus interface
> +
> +This file provides information for the davinci-emif chip select
> +bindings.
> +
> +This is a sub device node inside the davinci-emif device node
> +to describe a async bus for a specific chip select. For NAND,
> +CFI flash device bindings described inside an aemif node,
> +etc, a cs sub node is defined to associate the bus parameter
> +bindings used by the device.
> +
> +Required properties:=
> +- compatible: "ti,davinci-cs";
> +- #address-cells = <1>;
> +- #size-cells = <1>;
> +- cs - cs used by the device (NAND, CFI flash etc. values in the range: 2-5
No. Use ranges. See the discussion on OMAP GPMC.
Rob
> +
> +Optional properties:-
> +- asize - asynchronous data bus width (0 - 8bit, 1 - 16 bit)
> + All of the params below in nanoseconds
> +
> +- ta - Minimum turn around time
> +- rhold - read hold width
> +- rstobe - read strobe width
> +- rsetup - read setup width
> +- whold - write hold width
> +- wstrobe - write strobe width
> +- wsetup - write setup width
> +- ss - enable/disable select strobe (0 - disable, 1 - enable)
> +- ew - enable/disable extended wait cycles (0 - disable, 1 - enable)
> +
> +Example for davinci nand chip select
> +
> +aemif@60000000 {
> +
> + compatible = "ti,davinci-aemif";
> + #address-cells = <2>;
> + #size-cells = <1>;
> +
> + nand_cs:cs2@70000000 {
> + compatible = "ti,davinci-cs";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + cs = <2>;
> + asize = <1>;
> + ta = <24>;
> + rhold = <48>;
> + rstrobe = <390>;
> + rsetup = <96>;
> + whold = <48>;
> + wstrobe = <390>;
> + wsetup = <96>;
> + };
> +
> + nand@2,0 {
> +
> + ....
> +
> + };
> +};
> +
> +
> diff --git a/drivers/memory/Kconfig b/drivers/memory/Kconfig
> index 067f311..2636a95 100644
> --- a/drivers/memory/Kconfig
> +++ b/drivers/memory/Kconfig
> @@ -40,4 +40,14 @@ config TEGRA30_MC
> analysis, especially for IOMMU/SMMU(System Memory Management
> Unit) module.
>
> +config TI_DAVINCI_AEMIF
> + bool "Texas Instruments DaVinci AEMIF driver"
> + help
> + This driver is for the AEMIF module available in Texas Instruments
> + SoCs. AEMIF stands for Asynchronous External Memory Interface and
> + is intended to provide a glue-less interface to a variety of
> + asynchronuous memory devices like ASRAM, NOR and NAND memory. A total
> + of 256M bytes of any of these memories can be accessed at a given
> + time via four chip selects with 64M byte access per chip select.
> +
> endif
> diff --git a/drivers/memory/Makefile b/drivers/memory/Makefile
> index 42b3ce9..246aa61 100644
> --- a/drivers/memory/Makefile
> +++ b/drivers/memory/Makefile
> @@ -5,3 +5,4 @@
> obj-$(CONFIG_TI_EMIF) += emif.o
> obj-$(CONFIG_TEGRA20_MC) += tegra20-mc.o
> obj-$(CONFIG_TEGRA30_MC) += tegra30-mc.o
> +obj-$(CONFIG_TI_DAVINCI_AEMIF) += davinci-aemif.o
> diff --git a/drivers/memory/davinci-aemif.c b/drivers/memory/davinci-aemif.c
> new file mode 100644
> index 0000000..6c42116
> --- /dev/null
> +++ b/drivers/memory/davinci-aemif.c
> @@ -0,0 +1,397 @@
> +/*
> + * AEMIF support for DaVinci SoCs
> + *
> + * Copyright (C) 2010 Texas Instruments Incorporated. http://www.ti.com/
> + * Copyright (C) Heiko Schocher <hs@xxxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/err.h>
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/platform_data/davinci-aemif.h>
> +#include <linux/platform_device.h>
> +#include <linux/time.h>
> +
> +/* Timing value configuration */
> +#define TA(x) ((x) << 2)
> +#define RHOLD(x) ((x) << 4)
> +#define RSTROBE(x) ((x) << 7)
> +#define RSETUP(x) ((x) << 13)
> +#define WHOLD(x) ((x) << 17)
> +#define WSTROBE(x) ((x) << 20)
> +#define WSETUP(x) ((x) << 26)
> +#define EW(x) ((x) << 30)
> +#define SS(x) ((x) << 31)
> +
> +#define ASIZE_MAX 0x1
> +#define TA_MAX 0x3
> +#define RHOLD_MAX 0x7
> +#define RSTROBE_MAX 0x3f
> +#define RSETUP_MAX 0xf
> +#define WHOLD_MAX 0x7
> +#define WSTROBE_MAX 0x3f
> +#define WSETUP_MAX 0xf
> +#define EW_MAX 0x1
> +#define SS_MAX 0x1
> +#define NUM_CS 4
> +
> +#define CONFIG_MASK (TA(TA_MAX) | \
> + RHOLD(RHOLD_MAX) | \
> + RSTROBE(RSTROBE_MAX) | \
> + RSETUP(RSETUP_MAX) | \
> + WHOLD(WHOLD_MAX) | \
> + WSTROBE(WSTROBE_MAX) | \
> + WSETUP(WSETUP_MAX) | \
> + EW(EW_MAX) | SS(SS_MAX) | \
> + ASIZE_MAX)
> +
> +#define DRV_NAME "davinci-aemif"
> +
> +struct aemif_device {
> + struct davinci_aemif_pdata *cfg;
> + void __iomem *base;
> + struct clk *clk;
> +};
> +
> +static struct aemif_device *aemif;
> +/**
> + * aemif_calc_rate - calculate timing data.
> + * @wanted: The cycle time needed in nanoseconds.
> + * @clk: The input clock rate in kHz.
> + * @max: The maximum divider value that can be programmed.
> + *
> + * On success, returns the calculated timing value minus 1 for easy
> + * programming into AEMIF timing registers, else negative errno.
> + */
> +static int aemif_calc_rate(int wanted, unsigned long clk, int max)
> +{
> + int result;
> +
> + result = DIV_ROUND_UP((wanted * clk), NSEC_PER_MSEC) - 1;
> +
> + pr_debug("%s: result %d from %ld, %d\n", __func__, result, clk, wanted);
> +
> + /* It is generally OK to have a more relaxed timing than requested... */
> + if (result < 0)
> + result = 0;
> +
> + /* ... But configuring tighter timings is not an option. */
> + else if (result > max)
> + result = -EINVAL;
> +
> + return result;
> +}
> +
> +/**
> + * davinci_aemif_config_abus - configure async bus parameters given
> + * AEMIF interface
> + * @cs: chip-select to program the timing values for
> + * @data: aemif chip select configuration
> + * @base: aemif io mapped configuration base
> + *
> + * This function programs the given timing values (in real clock) into the
> + * AEMIF registers taking the AEMIF clock into account.
> + *
> + * This function does not use any locking while programming the AEMIF
> + * because it is expected that there is only one user of a given
> + * chip-select.
> + *
> + * Returns 0 on success, else negative errno.
> + */
> +static int davinci_aemif_config_abus(unsigned int cs,
> + void __iomem *base,
> + struct davinci_aemif_cs_data *data)
> +{
> + int ta, rhold, rstrobe, rsetup, whold, wstrobe, wsetup;
> + unsigned offset = A1CR_OFFSET + cs * 4;
> + unsigned long clkrate;
> + unsigned set, val;
> +
> + if (!data)
> + return -EINVAL;
> +
> + clkrate = clk_get_rate(aemif->clk);
> +
> + clkrate /= 1000; /* turn clock into kHz for ease of use */
> +
> + ta = aemif_calc_rate(data->ta, clkrate, TA_MAX);
> + rhold = aemif_calc_rate(data->rhold, clkrate, RHOLD_MAX);
> + rstrobe = aemif_calc_rate(data->rstrobe, clkrate, RSTROBE_MAX);
> + rsetup = aemif_calc_rate(data->rsetup, clkrate, RSETUP_MAX);
> + whold = aemif_calc_rate(data->whold, clkrate, WHOLD_MAX);
> + wstrobe = aemif_calc_rate(data->wstrobe, clkrate, WSTROBE_MAX);
> + wsetup = aemif_calc_rate(data->wsetup, clkrate, WSETUP_MAX);
> +
> + if (ta < 0 || rhold < 0 || rstrobe < 0 || rsetup < 0 ||
> + whold < 0 || wstrobe < 0 || wsetup < 0) {
> + pr_err("%s: cannot get suitable timings\n", __func__);
> + return -EINVAL;
> + }
> +
> + set = TA(ta) | RHOLD(rhold) | RSTROBE(rstrobe) | RSETUP(rsetup) |
> + WHOLD(whold) | WSTROBE(wstrobe) | WSETUP(wsetup);
> +
> + set |= (data->asize & ACR_ASIZE_MASK);
> + if (data->enable_ew)
> + set |= ACR_EW_MASK;
> + if (data->enable_ss)
> + set |= ACR_SS_MASK;
> +
> + val = readl(aemif->base + offset);
> + val &= ~CONFIG_MASK;
> + val |= set;
> + writel(val, aemif->base + offset);
> +
> + return 0;
> +}
> +
> +/**
> + * get_cs_data - helper function to get bus configuration data for a given cs
> + * @cs: chip-select, values 2-5
> + */
> +static struct davinci_aemif_cs_data *get_cs_data(int cs)
> +{
> + int i;
> +
> + for (i = 0; i < aemif->cfg->num_cs; i++) {
> + if (cs == aemif->cfg->cs_data[i].cs)
> + break;
> + }
> +
> + if (i == aemif->cfg->num_cs)
> + return NULL;
> +
> + return &aemif->cfg->cs_data[i];
> +}
> +
> +/**
> + * davinci_aemif_set_abus_params - Set bus configuration data for a given cs
> + * @cs: chip-select, values 2-5
> + * @data: ptr to a struct to hold the configuration data to be set
> + *
> + * This function is called to configure emif bus parameters for a given cs.
> + * Users call this function after calling davinci_aemif_get_abus_params()
> + * to get current parameters, modify and call this function
> + */
> +int davinci_aemif_set_abus_params(unsigned int cs,
> + struct davinci_aemif_cs_data *data)
> +{
> + struct davinci_aemif_cs_data *curr_cs_data;
> + int ret = -EINVAL, chip_cs;
> +
> + if (data == NULL)
> + return ret;
> +
> + if (aemif->base == NULL)
> + return ret;
> +
> + /* translate to chip CS which starts at 2 */
> + chip_cs = cs + 2;
> +
> + curr_cs_data = get_cs_data(chip_cs);
> + if (curr_cs_data) {
> + ret = davinci_aemif_config_abus(chip_cs, aemif->base, data);
> + if (!ret) {
> + *curr_cs_data = *data;
> + return 0;
> + }
> + }
> +
> + return ret;
> +}
> +EXPORT_SYMBOL(davinci_aemif_set_abus_params);
> +
> +/**
> + * davinci_aemif_get_abus_params - Get bus configuration data for a given cs
> + * @cs: chip-select, values 2-5
> + * returns: ptr to a struct having the current configuration data
> + */
> +struct davinci_aemif_cs_data *davinci_aemif_get_abus_params(unsigned int cs)
> +{
> + /* translate to chip CS which starts at 2 */
> + return get_cs_data(cs + 2);
> +}
> +EXPORT_SYMBOL(davinci_aemif_get_abus_params);
> +
> +#if defined(CONFIG_OF)
> +/**
> + * dv_get_value - helper function to read a attribute valye
> + * @np: device node ptr
> + * @name: name of the attribute
> + * returns: value of the attribute
> + */
> +static int dv_get_value(struct device_node *np, const char *name)
> +{
> + u32 data;
> + int ret;
> +
> + ret = of_property_read_u32(np, name, &data);
> + if (ret != 0)
> + return ret;
> +
> + return data;
> +}
> +
> +/**
> + * of_davinci_aemif_parse_abus_config - parse bus config data from a cs node
> + * @np: device node ptr
> + *
> + * This function update the emif async bus configuration based on the values
> + * configured in a cs device binding node.
> + */
> +static int of_davinci_aemif_parse_abus_config(struct device_node *np)
> +{
> + struct davinci_aemif_cs_data *data;
> + int cs;
> +
> +
> + cs = dv_get_value(np, "cs");
> + if (cs < 2 || cs >= NUM_CS)
> + return -EINVAL;
> +
> + if (aemif->cfg->num_cs >= NUM_CS)
> + return -EINVAL;
> +
> + data = &aemif->cfg->cs_data[aemif->cfg->num_cs++];
> + data->cs = cs;
> + data->ta = dv_get_value(np, "ta");
> + data->rhold = dv_get_value(np, "rhold");
> + data->rstrobe = dv_get_value(np, "rstrobe");
> + data->rsetup = dv_get_value(np, "rsetup");
> + data->whold = dv_get_value(np, "whold");
> + data->wstrobe = dv_get_value(np, "wstrobe");
> + data->wsetup = dv_get_value(np, "wsetup");
> + data->asize = dv_get_value(np, "asize");
> + data->enable_ew = dv_get_value(np, "ew");
> + data->enable_ss = dv_get_value(np, "ss");
> + return 0;
> +}
> +#endif
> +
> +static const struct of_device_id davinci_aemif_of_match[] __devinitconst = {
> + { .compatible = "ti,davinci-aemif", },
> + {},
> +};
> +
> +static const struct of_device_id davinci_cs_of_match[] __devinitconst = {
> + { .compatible = "ti,davinci-cs", },
> + {},
> +};
> +
> +/**
> + * of_davinci_aemif_cs_init - init cs data based on cs device nodes
> + * @np: device node ptr
> + *
> + * For every controller device node, there is a cs device node that
> + * describe the bus configuration parameters. This functions iterate
> + * over these nodes and update the cs data array.
> + */
> +static int of_davinci_aemif_cs_init(struct device_node *aemif_np)
> +{
> + struct device_node *np = aemif_np;
> +
> + if (!np)
> + return -ENODEV;
> +
> + for_each_matching_node(np, davinci_cs_of_match)
> + of_davinci_aemif_parse_abus_config(np);
> + return 0;
> +}
> +
> +static int __devinit davinci_aemif_probe(struct platform_device *pdev)
> +{
> + struct davinci_aemif_pdata *cfg;
> + int ret = -ENODEV, i;
> + struct resource *res;
> +
> + aemif = devm_kzalloc(&pdev->dev, sizeof(*aemif), GFP_KERNEL);
> +
> + if (!aemif)
> + return -ENOMEM;
> +
> + aemif->clk = clk_get(NULL, "aemif");
> + if (IS_ERR(aemif->clk))
> + return PTR_ERR(aemif->clk);
> +
> + clk_prepare_enable(aemif->clk);
> +
> + if (pdev->dev.platform_data == NULL) {
> + /* Not platform data, we get the cs data from the cs nodes */
> + cfg = devm_kzalloc(&pdev->dev, sizeof(*cfg), GFP_KERNEL);
> + if (cfg == NULL)
> + return -ENOMEM;
> +
> + aemif->cfg = cfg;
> + if (of_davinci_aemif_cs_init(pdev->dev.of_node) < 0) {
> + pr_err("No platform data or cs of node present\n");
> + goto error;
> + }
> + } else {
> + cfg = pdev->dev.platform_data;
> + aemif->cfg = cfg;
> + }
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + if (!res) {
> + pr_err("No IO memory address defined\n");
> + goto error;
> + }
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + aemif->base = devm_request_and_ioremap(&pdev->dev, res);
> + if (!aemif->base) {
> + ret = -EBUSY;
> + pr_err("ioremap failed\n");
> + goto error;
> + }
> +
> + for (i = 0; i < cfg->num_cs; i++) {
> + ret = davinci_aemif_config_abus(cfg->cs_data[i].cs,
> + aemif->base, &cfg->cs_data[i]);
> + if (ret < 0) {
> + pr_err("Error configuring chip select %d\n",
> + cfg->cs_data[i].cs);
> + goto error;
> + }
> + }
> + return ret;
> +error:
> + clk_disable_unprepare(aemif->clk);
> + clk_put(aemif->clk);
> + return ret;
> +}
> +
> +static struct platform_driver davinci_aemif_driver = {
> + .probe = davinci_aemif_probe,
> + .driver = {
> + .name = DRV_NAME,
> + .owner = THIS_MODULE,
> + .of_match_table = davinci_aemif_of_match,
> + },
> +};
> +
> +static int __init davinci_aemif_init(void)
> +{
> + return platform_driver_register(&davinci_aemif_driver);
> +}
> +subsys_initcall(davinci_aemif_init);
> +
> +static void __exit davinci_aemif_exit(void)
> +{
> + clk_disable_unprepare(aemif->clk);
> + clk_put(aemif->clk);
> + platform_driver_unregister(&davinci_aemif_driver);
> +}
> +module_exit(davinci_aemif_exit);
> +
> +MODULE_AUTHOR("Murali Karicheri <m-karicheri2@xxxxxx>");
> +MODULE_DESCRIPTION("Texas Instruments AEMIF driver");
> +MODULE_LICENSE("GPL v2");
> +MODULE_ALIAS("platform:" DRV_NAME);
> diff --git a/include/linux/platform_data/davinci-aemif.h b/include/linux/platform_data/davinci-aemif.h
> new file mode 100644
> index 0000000..03f3ad0
> --- /dev/null
> +++ b/include/linux/platform_data/davinci-aemif.h
> @@ -0,0 +1,47 @@
> +/*
> + * TI DaVinci AEMIF support
> + *
> + * Copyright 2010 (C) Texas Instruments, Inc. http://www.ti.com/
> + *
> + * This file is licensed under the terms of the GNU General Public License
> + * version 2. This program is licensed "as is" without any warranty of any
> + * kind, whether express or implied.
> + */
> +#ifndef _MACH_DAVINCI_AEMIF_H
> +#define _MACH_DAVINCI_AEMIF_H
> +
> +#define NRCSR_OFFSET 0x00
> +#define AWCCR_OFFSET 0x04
> +#define A1CR_OFFSET 0x10
> +
> +#define ACR_ASIZE_MASK 0x3
> +#define ACR_EW_MASK BIT(30)
> +#define ACR_SS_MASK BIT(31)
> +#define ASIZE_16BIT 1
> +
> +struct davinci_aemif_cs_data {
> + u8 cs;
> + u16 wstrobe;
> + u16 rstrobe;
> + u8 wsetup;
> + u8 whold;
> + u8 rsetup;
> + u8 rhold;
> + u8 ta;
> + u8 enable_ss;
> + u8 enable_ew;
> + u8 asize;
> +};
> +
> +struct davinci_aemif_pdata {
> + u8 num_cs;
> + struct davinci_aemif_cs_data cs_data[4];
> +};
> +
> +/* API to Get current Asynchrnous emif bus parameters */
> +struct davinci_aemif_cs_data *davinci_aemif_get_abus_params(unsigned int cs);
> +
> +/* API to Set current Asynchrnous emif bus parameters */
> +int davinci_aemif_set_abus_params(unsigned int cs,
> + struct davinci_aemif_cs_data *data);
> +#endif
>
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
