On Thu, Oct 04, 2012 at 15:51:03, Philip, Avinash wrote:
> On Thu, Oct 04, 2012 at 00:50:45, Ivan Djelic wrote:
> > On Wed, Oct 03, 2012 at 03:29:49PM +0100, Philip, Avinash wrote:
> > > ELM module can be used for error correction of BCH 4 & 8 bit. Also
> > > support read & write page in one shot by adding custom read_page &
> > > write_page methods. This helps in optimizing code.
> > >
> > > New structure member "is_elm_used" is added to know the status of
> > > whether the ELM module is used for error correction or not.
> > >
> > > Note:
> > > ECC layout of BCH8 uses 14 bytes for 512 byte of data to make compatible
> > > with RBL ECC layout, even though the requirement was only 13 byte. This
> > > results a common ecc layout across RBL, U-boot & Linux.
> > >
> >
> > See a few comments below,
> >
> > (...)
> > > +static int omap_elm_correct_data(struct mtd_info *mtd, u_char *dat,
> > > + u_char *read_ecc, u_char *calc_ecc)
> > > +{
> > > + struct omap_nand_info *info = container_of(mtd, struct omap_nand_info,
> > > + mtd);
> > > + int eccsteps = info->nand.ecc.steps;
> > > + int i , j, stat = 0;
> > > + int eccsize, eccflag, size;
> > > + struct elm_errorvec err_vec[ERROR_VECTOR_MAX];
> > > + u_char *ecc_vec = calc_ecc;
> > > + enum bch_ecc type;
> > > + bool is_error_reported = false;
> > > +
> > > + /* initialize elm error vector to zero */
> > > + memset(err_vec, 0, sizeof(err_vec));
> > > + if (info->nand.ecc.strength == BCH8_MAX_ERROR) {
> > > + size = BCH8_SIZE;
> > > + eccsize = BCH8_ECC_OOB_BYTES;
> > > + type = BCH8_ECC;
> > > + } else {
> > > + size = BCH4_SIZE;
> > > + eccsize = BCH4_SIZE;
> > > + type = BCH4_ECC;
> > > + }
> > > +
> > > + for (i = 0; i < eccsteps ; i++) {
> > > + eccflag = 0; /* initialize eccflag */
> > > +
> > > + for (j = 0; (j < eccsize); j++) {
> > > + if (read_ecc[j] != 0xFF) {
> > > + eccflag = 1; /* data area is flashed */
> >
> > Just a reminder: this way of checking if a page has been programmed is not robust to bitflips,
> > so you may get into trouble with UBIFS on a fairly recent device.
Sorry I missed this point.
Here we were checking data in spare area (only in ecc layout 14*4 for BCH8) is 0xFF. If all data
in spare area is 0xFF, conclude that the page is erased & no need of error correction. In case
of bit flip present in spare area, page will be reported as uncorrectable.
But I am not understand understand " trouble with UBIFS on a fairly recent device".
Can you little elaborativ
Thanks
Avinash
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
