Re: [PATCH v2 3/3] usb: musb: omap: Add device tree support for omap musb glue

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi,

On Tue, Sep 11, 2012 at 3:23 PM, Vaibhav Hiremath <hvaibhav@xxxxxx> wrote:
>
>
> On 9/11/2012 2:39 PM, Kishon Vijay Abraham I wrote:
>> Added device tree support for omap musb driver and updated the
>> Documentation with device tree binding information.
>>
>> Signed-off-by: Kishon Vijay Abraham I <kishon@xxxxxx>
>> ---
>>  Documentation/devicetree/bindings/usb/omap-usb.txt |   33 ++++++++++++
>>  drivers/usb/musb/omap2430.c                        |   54 ++++++++++++++++++++
>>  2 files changed, 87 insertions(+)
>>  create mode 100644 Documentation/devicetree/bindings/usb/omap-usb.txt
>>
>> diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt
>> new file mode 100644
>> index 0000000..29a043e
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt
>> @@ -0,0 +1,33 @@
>> +OMAP GLUE
>> +
>> +OMAP MUSB GLUE
>> + - compatible : Should be "ti,omap4-musb" or "ti,omap3-musb"
>> + - ti,hwmods : must be "usb_otg_hs"
>> + - multipoint : Should be "1" indicating the musb controller supports
>> +   multipoint. This is a MUSB configuration-specific setting.
>> + - num_eps : Specifies the number of endpoints. This is also a
>> +   MUSB configuration-specific setting. Should be set to "16"
>> + - ram_bits : Specifies the ram address size. Should be set to "12"
>> + - interface_type : This is a board specific setting to describe the type of
>> +   interface between the controller and the phy. It should be "0" or "1"
>> +   specifying ULPI and UTMI respectively.
>> + - mode : Should be "3" to represent OTG. "1" signifies HOST and "2"
>> +   represents PERIPHERAL.
>> + - power : Should be "50". This signifies the controller can supply upto
>> +   100mA when operating in host mode.
>> +
>> +SOC specific device node entry
>> +usb_otg_hs: usb_otg_hs@4a0ab000 {
>> +     compatible = "ti,omap4-musb";
>> +     ti,hwmods = "usb_otg_hs";
>> +     multipoint = <1>;
>> +     num_eps = <16>;
>> +     ram_bits = <12>;
>> +};
>
>
> reg and interrupt properties are missing here.
>
> I would encourage to specify "reg" and "interrupt" properties in every
> node getting newly added to the OMAP DTS files.

Sure. will add that in my next version.

Thanks
Kishon
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html


[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux FS]     [Yosemite Forum]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux