Linus Walleij wrote at Tuesday, February 21, 2012 5:40 AM:
> On Tue, Feb 21, 2012 at 12:06 PM, Russell King - ARM Linux
> <linux@xxxxxxxxxxxxxxxx> wrote:
>
> >> It's a bit kludgy but works and makes sure the pins are only used
> >> for one thing at a time.
> >
> > No. The case which I'm thinking of is for the Assabet audio, where
> > we have the following situation.
>
> OK... (thanks for the explanation!)
>
> > The solution is to wait for SSP to finish, and while SSP is still enabled,
> > switch the pins from the SSP block to the GPIO block and toggle the SFRM
> > signal to flip the WS output before removing power. When starting up,
> > with the pins under control of GPIO, power up and them toggle hte SFRM
> > signal to restore the WS state before giving it back to the SSP block.
> >
> > However, here's the thing: SSP must be enabled at the point in time when
> > the pins are given or taken away from it, otherwise SFRM is indeterminant.
> > We can't allow gpio_request() to fail at the points where we toggle this
> > pin - failure is not really an option where causing hardware stress is
> > involved. We can't allow the GPIO block to have the state of these pins
> > change state while the pins are given back to the GPIO block before the
> > GPIOs have been requested (glitches on the SFRM line will cause the state
> > of the FIFO to change.)
>
> This can probably be done, mainly I'd say that control over the pins
> need not mean that they are decoupled from some specific hardware, or
> that the hardware is disabled or so, the semantics of doing say
> pinctrl_get/enable/disable/put aren't set in stone, it's just callbacks into
> the device driver so it could avoid doing anything in this case, keep
> the pins muxed for the SSP if the transition goes from SSP->GPIO
> and back.
>
> However I guess it would be conceptually closer if say the pins could
> be used for a device and GPIO at the *same time*.
If we allowed that, it would also solve the following comment in patch
2 in this series, in the Tegra GPIO driver:
int tegra_gpio_request(struct gpio_chip *chip, unsigned offset)
{
/*
* We should call pinctrl_request_gpio() here. However, we can't. Tegra
* muxes pins in groups not individually, and real boards exist where
* most of a pin group needs to be used for some function, yet some of
* the pins aren't actually used by that function in the mode the
* controller operates on the board, and so those pins can be used as
* GPIOs.
*
* This is true in practice on Seaboard/Springbank, where pin group ATC
* is used by the NAND controller, but pin GMI_IORDY_PI5 is used as a
* GPIO for the SD card slot's CD signal.
*
* On Tegra30, pins are muxed in groups and hence we could call
* pinctrl here, but we don't for now.
*/
tegra_gpio_mask_write(GPIO_MSK_CNF(offset), offset, 1);
return 0;
}
i.e. we actually /could/ call pinctrl_request_gpio() here.
And in turn, the I2C driver (in your example) and SPI driver (in Russell's)
would never have to call pinctrl_disable() and hence the issue I raised
in my previous email would not occur.
The one downside here:
Ignoring WARs like we're discussing, it's typically true that a given pin
should either be a special function or a GPIO for any given board. If
we do allow a pin to be owned/used by both, then how do we indicate, on
a per-board rather than per-SoC basis, which pins we should allow both
gpio_request() and pinmux usage? The following considerations exist:
a) On Tegra, a pin group might include 10 pins that are mux'd as a group,
hence all owned e.g. by a NAND driver. If a few of those aren't used on a
particular board due to the way the NAND is hooked up and the driver
configured, do we only allow gpio_request() only on those pins we know the
NAND driver isn't actually using, to prevent someone using unexpected
pins as GPIO? We'd need a per-GPIO per-board way to represent this if
we care about this level of error-checking.
b) In Linus's snooping example, how do we know the SoC can physically
implement enabling a pin as both a GPIO and a special function, such
that the gpio_request() for the snooping won't interfere with the mux'd
function? On Tegra, any GPIO usage is mutually exclusive with mux usage;
enabling GPIO even for input, disconnects the input side of the pin from
any HW module other than GPIO irrespective of mux function. IIRC,
somewhere some per-pin data was mentioned for this.
We could either:
1) Just ignore these issues, and allow both mux and GPIO ownership at
once of any pin, and leave it up to platform data or device tree authors
to give the correct GPIO IDs to drivers. This is possibly reasonable, but
I just want us to make this a conscious decision.
2) Extend the pinctrl mapping table to explicitly represent GPIO usage.
This is required anyway for HW where there isn't a 1:1 mapping between
GPIO ID and pin ID, e.g. 1 pin could be used for two different GPIO
signals, e.g. 1 from each of 2 different GPIO HW modules, with different
capabilities, or where 1 GPIO could be routed to one of 2 or more pins.
In other words, make "gpio" an explicit mux function, thus allowing
pinctrl_select_state() to directly transition between special function
and GPIO usage, rather than having separate pinctrl and GPIO APIs for
this. This way would entail dropping my Documentation/gpio.txt patch
completely, I think.
If we do this though, I think we'd want to extend pinctrl to allow muxing
on pins too, so that we don't need to create a pin group for every pin to
support per-pin GPIO ownership. This would also help out all the HW that
already muxes everything per-pin, since they need to create these single-
pin groups right now... I somewhat anticpated this in my naming of the
mapping table convenience macros in the most recent pinctrl patch I posted
to add pin config mapping table entries.
Thoughts?
--
nvpublic
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
