On Thu Dec 14, 2023 at 11:36 AM CET, Om Prakash Singh wrote:
> Add the QCE and Crypto BAM DMA nodes.
>
> Signed-off-by: Om Prakash Singh <quic_omprsing@xxxxxxxxxxx>
> ---
>
> Changes in V3:
> - V2 patch was sent without actual modification. Resending the patch with modified file.
>
> Changes in V2:
> - Update DT node sequence as per register ascending order.
> - Fix DT node properties as per convention.
>
> arch/arm64/boot/dts/qcom/sc7280.dtsi | 22 ++++++++++++++++++++++
> 1 file changed, 22 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> index 66f1eb83cca7..b819724c1255 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> @@ -2233,6 +2233,28 @@ pcie1_phy: phy@1c0e000 {
> status = "disabled";
> };
>
> + cryptobam: dma-controller@1dc4000 {
> + compatible = "qcom,bam-v1.7.4", "qcom,bam-v1.7.0";
> + reg = <0x0 0x01dc4000 0x0 0x28000>;
> + interrupts = <GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>;
> + #dma-cells = <1>;
> + iommus = <&apps_smmu 0x4e4 0x0011>,
> + <&apps_smmu 0x4e6 0x0011>;
> + qcom,ee = <0>;
> + qcom,controlled-remotely;
> + };
Hi,
Unfortunately I seem to have boot failure / device crash with cryptobam
enabled on my qcm6490-fairphone-fp5. Are you aware of any firmware
differences that could cause this with QCM6490 LA firmware?
Looking at downstream msm-5.4 dmesg I do see this BAM being used so it
should generally be accessible from Linux.
[ 5.217214] qce 1de0000.qcedev: Adding to iommu group 18
[ 5.223741] QCE50: __qce_get_device_tree_data: CE operating frequency is not defined, setting to default 100MHZ
[ 5.234986] qce 1de0000.qcedev: QTI Crypto 5.6.0 device found @0x1de0000
[ 5.242981] sps_register_bam_device: sps:BAM 0x0000000001dc4000 is registered
[ 5.251124] sps_bam_enable: sps:BAM 0x0000000001dc4000 (va:0x000000001db63156) enabled: ver:0x27, number of pipes:16
[ 5.262783] QCE50: qce_sps_init: QTI MSM CE-BAM at 0x0000000001dc4000 irq 9
[ 5.271820] qce 1de0000.qcedev:qcom_cedev_ns_cb: Adding to iommu group 19
[ 5.281083] qce 1de0000.qcedev:qcom_cedev_s_cb: Adding to iommu group 20
[ 5.289376] qcrypto 1de0000.qcrypto: Adding to iommu group 21
[ 5.296326] QCE50: __qce_get_device_tree_data: CE operating frequency is not defined, setting to default 100MHZ
[ 5.307675] qcrypto 1de0000.qcrypto: QTI Crypto 5.6.0 device found @0x1de0000
[ 5.315867] QCE50: qce_sps_init: QTI MSM CE-BAM at 0x0000000001dc4000 irq 9
Any idea?
Regards
Luca
> +
> + crypto: crypto@1dfa000 {
> + compatible = "qcom,sc7280-qce", "qcom,sm8150-qce", "qcom,qce";
> + reg = <0x0 0x01dfa000 0x0 0x6000>;
> + dmas = <&cryptobam 4>, <&cryptobam 5>;
> + dma-names = "rx", "tx";
> + iommus = <&apps_smmu 0x4e4 0x0011>,
> + <&apps_smmu 0x4e4 0x0011>;
> + interconnects = <&aggre2_noc MASTER_CRYPTO 0 &mc_virt SLAVE_EBI1 0>;
> + interconnect-names = "memory";
> + };
> +
> ipa: ipa@1e40000 {
> compatible = "qcom,sc7280-ipa";
>
