On 10/4/2023 3:50 pm, Herbert Xu wrote:
> On Mon, Apr 10, 2023 at 03:37:52PM +0800, Jia Jie Ho wrote:
>>
>> +static void starfive_hash_start(void *param)
>> +{
>> + struct starfive_cryp_ctx *ctx = param;
>> + struct starfive_cryp_request_ctx *rctx = ctx->rctx;
>> + struct starfive_cryp_dev *cryp = ctx->cryp;
>> + union starfive_alg_cr alg_cr;
>> + union starfive_hash_csr csr;
>> +
>> + dma_unmap_sg(cryp->dev, rctx->in_sg, rctx->in_sg_len, DMA_TO_DEVICE);
>> +
>> + alg_cr.v = 0;
>> + alg_cr.clear = 1;
>> +
>> + writel(alg_cr.v, cryp->base + STARFIVE_ALG_CR_OFFSET);
>> +
>> + csr.v = readl(cryp->base + STARFIVE_HASH_SHACSR);
>> + csr.firstb = 0;
>> + csr.final = 1;
>> +
>> + reinit_completion(&cryp->hash_done);
>> + writel(~STARFIVE_IE_MASK_HASH_DONE, cryp->base + STARFIVE_IE_MASK_OFFSET);
>> + writel(csr.v, cryp->base + STARFIVE_HASH_SHACSR);
>> +}
>
> Why are you still using a completion? The callback function should
> invoke the crypto_engine finalize_request call directly.
>
Hi Herbert,
The hardware requires user to set a 'final' bit after data transfer completed.
This completion is to wait for the interrupt signal from device that the final digest
has been populated to the read registers.
I'll do the finalize_request call directly in the next version.
>> +static int starfive_hash_xmit(struct starfive_cryp_ctx *ctx)
>> +{
>> + struct starfive_cryp_request_ctx *rctx = ctx->rctx;
>> + struct starfive_cryp_dev *cryp = ctx->cryp;
>> + int ret;
>> +
>> + rctx->csr.hash.v = 0;
>> + rctx->csr.hash.reset = 1;
>> + writel(rctx->csr.hash.v, cryp->base + STARFIVE_HASH_SHACSR);
>> +
>> + if (starfive_hash_wait_busy(ctx))
>> + return dev_err_probe(cryp->dev, -ETIMEDOUT, "Error resetting engine.\n");
>> +
>> + rctx->csr.hash.v = 0;
>> + rctx->csr.hash.mode = ctx->hash_mode & STARFIVE_HASH_MODE_MASK;
>> + rctx->csr.hash.ie = 1;
>> +
>> + if (ctx->hash_mode & STARFIVE_HASH_HMAC_FLAGS) {
>> + ret = starfive_hash_hmac_key(ctx);
>> + if (ret)
>> + return ret;
>> + } else {
>> + rctx->csr.hash.start = 1;
>> + rctx->csr.hash.firstb = 1;
>> + writel(rctx->csr.hash.v, cryp->base + STARFIVE_HASH_SHACSR);
>> + }
>> +
>> + ret = starfive_hash_xmit_dma(ctx);
>> + if (ret)
>> + return ret;
>> +
>> + if (!wait_for_completion_timeout(&cryp->hash_done, msecs_to_jiffies(10000)))
>> + return dev_err_probe(cryp->dev, -ETIMEDOUT, "Timeout waiting for hash done\n");
>
> There is no point in waiting for completion. Just return 0 and
> you're done.
>
I'll change this in the next version too.
Thanks for taking time reviewing this patch.
Best regards,
Jia Jie
