From: Kyung Min Park <kyung.min.park@xxxxxxxxx> Update the crc_pcl function that calculates T10 Data Integrity Field CRC16 (CRC T10 DIF) using VPCLMULQDQ instruction. VPCLMULQDQ instruction with AVX-512F adds EVEX encoded 512 bit version of PCLMULQDQ instruction. The advantage comes from packing multiples of 4 * 128 bit data into AVX512 reducing instruction latency. The glue code in crct10diff module overrides the existing PCLMULQDQ version with the VPCLMULQDQ version when the following criteria are met: At compile time: 1. CONFIG_CRYPTO_AVX512 is enabled 2. toolchain(assembler) supports VPCLMULQDQ instructions At runtime: 1. VPCLMULQDQ and AVX512VL features are supported on a platform (currently only Icelake) 2. If compiled as built-in module, crct10dif_pclmul.use_avx512 is set at boot time or /sys/module/crct10dif_pclmul/parameters/use_avx512 is set to 1 after boot. If compiled as loadable module, use_avx512 module parameter must be set: modprobe crct10dif_pclmul use_avx512=1 A typical run of tcrypt with CRC T10 DIF calculation with PCLMULQDQ instruction and VPCLMULQDQ instruction shows the following results: For bytes per update >= 1KB, we see the average improvement of 46%(~1.4x) For bytes per update < 1KB, we see the average improvement of 13%. Test was performed on an Icelake based platform with constant frequency set for CPU. Detailed results for a variety of block sizes and update sizes are in the table below. --------------------------------------------------------------------------- | | | cycles/operation | | | | | (the lower the better) | | | byte | bytes |----------------------------------| percentage | | blocks | per update | CRC T10 DIF | CRC T10 DIF | loss/gain | | | | with PCLMULQDQ | with VPCLMULQDQ | | |------------|------------|----------------|-----------------|------------| | 16 | 16 | 77 | 106 | -27.0 | | 64 | 16 | 411 | 390 | 5.4 | | 64 | 64 | 71 | 85 | -16.0 | | 256 | 16 | 1224 | 1308 | -6.4 | | 256 | 64 | 393 | 407 | -3.4 | | 256 | 256 | 93 | 86 | 8.1 | | 1024 | 16 | 4564 | 5020 | -9.0 | | 1024 | 256 | 486 | 475 | 2.3 | | 1024 | 1024 | 221 | 148 | 49.3 | | 2048 | 16 | 8945 | 9851 | -9.1 | | 2048 | 256 | 982 | 951 | 3.3 | | 2048 | 1024 | 500 | 369 | 35.5 | | 2048 | 2048 | 413 | 265 | 55.8 | | 4096 | 16 | 17885 | 19351 | -7.5 | | 4096 | 256 | 1828 | 1713 | 6.7 | | 4096 | 1024 | 968 | 805 | 20.0 | | 4096 | 4096 | 739 | 475 | 55.6 | | 8192 | 16 | 48339 | 41556 | 16.3 | | 8192 | 256 | 3494 | 3342 | 4.5 | | 8192 | 1024 | 1959 | 1462 | 34.0 | | 8192 | 4096 | 1561 | 1036 | 50.7 | | 8192 | 8192 | 1540 | 1004 | 53.4 | --------------------------------------------------------------------------- This work was inspired by the CRC T10 DIF AVX512 optimization published in Intel Intelligent Storage Acceleration Library. https://github.com/intel/isa-l/blob/master/crc/crc16_t10dif_by16_10.asm Co-developed-by: Greg Tucker <greg.b.tucker@xxxxxxxxx> Signed-off-by: Greg Tucker <greg.b.tucker@xxxxxxxxx> Co-developed-by: Tomasz Kantecki <tomasz.kantecki@xxxxxxxxx> Signed-off-by: Tomasz Kantecki <tomasz.kantecki@xxxxxxxxx> Signed-off-by: Kyung Min Park <kyung.min.park@xxxxxxxxx> Signed-off-by: Megha Dey <megha.dey@xxxxxxxxx> --- arch/x86/crypto/Makefile | 1 + arch/x86/crypto/crct10dif-avx512-asm_64.S | 482 ++++++++++++++++++++++++++++++ arch/x86/crypto/crct10dif-pclmul_glue.c | 24 +- arch/x86/include/asm/disabled-features.h | 8 +- crypto/Kconfig | 23 ++ 5 files changed, 535 insertions(+), 3 deletions(-) create mode 100644 arch/x86/crypto/crct10dif-avx512-asm_64.S diff --git a/arch/x86/crypto/Makefile b/arch/x86/crypto/Makefile index a31de0c..bf0b0fc 100644 --- a/arch/x86/crypto/Makefile +++ b/arch/x86/crypto/Makefile @@ -80,6 +80,7 @@ crc32-pclmul-y := crc32-pclmul_asm.o crc32-pclmul_glue.o obj-$(CONFIG_CRYPTO_CRCT10DIF_PCLMUL) += crct10dif-pclmul.o crct10dif-pclmul-y := crct10dif-pcl-asm_64.o crct10dif-pclmul_glue.o +crct10dif-pclmul-$(CONFIG_CRYPTO_CRCT10DIF_AVX512) += crct10dif-avx512-asm_64.o obj-$(CONFIG_CRYPTO_POLY1305_X86_64) += poly1305-x86_64.o poly1305-x86_64-y := poly1305-x86_64-cryptogams.o poly1305_glue.o diff --git a/arch/x86/crypto/crct10dif-avx512-asm_64.S b/arch/x86/crypto/crct10dif-avx512-asm_64.S new file mode 100644 index 0000000..07c9371 --- /dev/null +++ b/arch/x86/crypto/crct10dif-avx512-asm_64.S @@ -0,0 +1,482 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ +/* Copyright(c) 2020 Intel Corporation. + * + * Implement CRC T10 DIF calculation with AVX512 instructions. (x86_64) + * + * This is CRC T10 DIF calculation with AVX512 instructions. It requires + * the support of Intel(R) AVX512F and VPCLMULQDQ instructions. + */ + +#include <linux/linkage.h> + +.text +#define init_crc %edi +#define buf %rsi +#define len %rdx +#define VARIABLE_OFFSET 16*2+8 + +/* + * u16 crct10dif-avx512-asm_64(u16 init_crc, const u8 *buf, size_t len); + */ +.align 16 +SYM_FUNC_START(crct10dif_pcl_avx512) + + shl $16, init_crc + /* + * The code flow is exactly same as a 32-bit CRC. The only difference + * is before returning eax, we will shift it right 16 bits, to scale + * back to 16 bits. + */ + sub $(VARIABLE_OFFSET), %rsp + + vbroadcasti32x4 SHUF_MASK(%rip), %zmm18 + + /* For sizes less than 256 bytes, we can't fold 256 bytes at a time. */ + cmp $256, len + jl .less_than_256 + + /* load the initial crc value */ + vmovd init_crc, %xmm10 + + /* + * crc value does not need to be byte-reflected, but it needs to be + * moved to the high part of the register because data will be + * byte-reflected and will align with initial crc at correct place. + */ + vpslldq $12, %xmm10, %xmm10 + + /* receive the initial 64B data, xor the initial crc value. */ + vmovdqu8 (buf), %zmm0 + vmovdqu8 16*4(buf), %zmm4 + vpshufb %zmm18, %zmm0, %zmm0 + vpshufb %zmm18, %zmm4, %zmm4 + vpxorq %zmm10, %zmm0, %zmm0 + vbroadcasti32x4 rk3(%rip), %zmm10 + + sub $256, len + cmp $256, len + jl .fold_128_B_loop + + vmovdqu8 16*8(buf), %zmm7 + vmovdqu8 16*12(buf), %zmm8 + vpshufb %zmm18, %zmm7, %zmm7 + vpshufb %zmm18, %zmm8, %zmm8 + vbroadcasti32x4 rk_1(%rip), %zmm16 + sub $256, len + +.fold_256_B_loop: + add $256, buf + vmovdqu8 (buf), %zmm3 + vpshufb %zmm18, %zmm3, %zmm3 + vpclmulqdq $0x00, %zmm16, %zmm0, %zmm1 + vpclmulqdq $0x11, %zmm16, %zmm0, %zmm2 + vpxorq %zmm2, %zmm1, %zmm0 + vpxorq %zmm3, %zmm0, %zmm0 + + vmovdqu8 16*4(buf), %zmm9 + vpshufb %zmm18, %zmm9, %zmm9 + vpclmulqdq $0x00, %zmm16, %zmm4, %zmm5 + vpclmulqdq $0x11, %zmm16, %zmm4, %zmm6 + vpxorq %zmm6, %zmm5, %zmm4 + vpxorq %zmm9, %zmm4, %zmm4 + + vmovdqu8 16*8(buf), %zmm11 + vpshufb %zmm18, %zmm11, %zmm11 + vpclmulqdq $0x00, %zmm16, %zmm7, %zmm12 + vpclmulqdq $0x11, %zmm16, %zmm7, %zmm13 + vpxorq %zmm13, %zmm12, %zmm7 + vpxorq %zmm11, %zmm7, %zmm7 + + vmovdqu8 16*12(buf), %zmm17 + vpshufb %zmm18, %zmm17, %zmm17 + vpclmulqdq $0x00, %zmm16, %zmm8, %zmm14 + vpclmulqdq $0x11, %zmm16, %zmm8, %zmm15 + vpxorq %zmm15, %zmm14, %zmm8 + vpxorq %zmm17, %zmm8, %zmm8 + + sub $256, len + jge .fold_256_B_loop + + /* Fold 256 into 128 */ + add $256, buf + vpclmulqdq $0x00, %zmm10, %zmm0, %zmm1 + vpclmulqdq $0x11, %zmm10, %zmm0, %zmm2 + vpternlogq $0x96, %zmm2, %zmm1, %zmm7 + + vpclmulqdq $0x00, %zmm10, %zmm4, %zmm5 + vpclmulqdq $0x11, %zmm10, %zmm4, %zmm6 + vpternlogq $0x96, %zmm6, %zmm5, %zmm8 + + vmovdqa32 %zmm7, %zmm0 + vmovdqa32 %zmm8, %zmm4 + + add $128, len + jmp .fold_128_B_register + + /* + * At this section of the code, there is 128*x + y (0 <= y < 128) bytes + * of buffer. The fold_128_B_loop will fold 128B at a time until we have + * 128 + y Bytes of buffer. + * Fold 128B at a time. This section of the code folds 8 xmm registers + * in parallel. + */ +.fold_128_B_loop: + add $128, buf + vmovdqu8 (buf), %zmm8 + vpshufb %zmm18, %zmm8, %zmm8 + vpclmulqdq $0x00, %zmm10, %zmm0, %zmm2 + vpclmulqdq $0x11, %zmm10, %zmm0, %zmm1 + vpxorq %zmm1, %zmm2, %zmm0 + vpxorq %zmm8, %zmm0, %zmm0 + + vmovdqu8 16*4(buf), %zmm9 + vpshufb %zmm18, %zmm9, %zmm9 + vpclmulqdq $0x00, %zmm10, %zmm4, %zmm5 + vpclmulqdq $0x11, %zmm10, %zmm4, %zmm6 + vpxorq %zmm6, %zmm5, %zmm4 + vpxorq %zmm9, %zmm4, %zmm4 + + sub $128, len + jge .fold_128_B_loop + + add $128, buf + + /* + * At this point, the buffer pointer is pointing at the last y Bytes + * of the buffer, where 0 <= y < 128. The 128B of folded data is in + * 8 of the xmm registers: xmm0 - xmm7. + */ +.fold_128_B_register: + /* fold the 8 128b parts into 1 xmm register with different constant. */ + vmovdqu8 rk9(%rip), %zmm16 + vmovdqu8 rk17(%rip), %zmm11 + vpclmulqdq $0x00, %zmm16, %zmm0, %zmm1 + vpclmulqdq $0x11, %zmm16, %zmm0, %zmm2 + vextracti64x2 $3, %zmm4, %xmm7 + + vpclmulqdq $0x00, %zmm11, %zmm4, %zmm5 + vpclmulqdq $0x11, %zmm11, %zmm4, %zmm6 + vmovdqa rk1(%rip), %xmm10 + vpternlogq $0x96, %zmm5, %zmm2, %zmm1 + vpternlogq $0x96, %zmm7, %zmm6, %zmm1 + + vshufi64x2 $0x4e, %zmm1, %zmm1, %zmm8 + vpxorq %ymm1, %ymm8, %ymm8 + vextracti64x2 $1, %ymm8, %xmm5 + vpxorq %xmm8, %xmm5, %xmm7 + + /* + * Instead of 128, we add 128 - 16 to the loop counter to save one + * instruction from the loop. Instead of a cmp instruction, we use + * the negative flag with the jl instruction. + */ + add $(128 - 16), len + jl .final_reduction_for_128 + + /* + * Now we have 16 + y bytes left to reduce. 16 Bytes is in register xmm7 + * and the rest is in memory we can fold 16 bytes at a time if y >= 16. + * continue folding 16B at a time. + */ +.16B_reduction_loop: + vpclmulqdq $0x11, %xmm10, %xmm7, %xmm8 + vpclmulqdq $0x00, %xmm10, %xmm7, %xmm7 + vpxor %xmm8, %xmm7, %xmm7 + vmovdqu (buf), %xmm0 + vpshufb %xmm18, %xmm0, %xmm0 + vpxor %xmm0, %xmm7, %xmm7 + add $16, buf + sub $16, len + + /* + * Instead of a cmp instruction, we utilize the flags with the jge + * instruction equivalent of: cmp len, 16-16. Check if there is any + * more 16B in the buffer to be able to fold. + */ + jge .16B_reduction_loop + + /* + * now we have 16+z bytes left to reduce, where 0 <= z < 16. + * first, we reduce the data in the xmm7 register. + */ +.final_reduction_for_128: + add $16, len + je .128_done + + /* + * Here we are getting data that is less than 16 bytes. since we know + * that there was data before the pointer, we can offset the input + * pointer before the actual point to receive exactly 16 bytes. + * After that, the registers need to be adjusted. + */ +.get_last_two_xmms: + vmovdqa %xmm7, %xmm2 + vmovdqu -16(buf, len), %xmm1 + vpshufb %xmm18, %xmm1, %xmm1 + + /* + * get rid of the extra data that was loaded before. + * load the shift constant + */ + lea 16 + pshufb_shf_table(%rip), %rax + sub len, %rax + vmovdqu (%rax), %xmm0 + + vpshufb %xmm0, %xmm2, %xmm2 + vpxor mask1(%rip), %xmm0, %xmm0 + vpshufb %xmm0, %xmm7, %xmm7 + vpblendvb %xmm0, %xmm2, %xmm1, %xmm1 + + vpclmulqdq $0x11, %xmm10, %xmm7, %xmm8 + vpclmulqdq $0x00, %xmm10, %xmm7, %xmm7 + vpxor %xmm8, %xmm7, %xmm7 + vpxor %xmm1, %xmm7, %xmm7 + +.128_done: + /* compute crc of a 128-bit value. */ + vmovdqa rk5(%rip), %xmm10 + vmovdqa %xmm7, %xmm0 + + vpclmulqdq $0x01, %xmm10, %xmm7, %xmm7 + vpslldq $8, %xmm0, %xmm0 + vpxor %xmm0, %xmm7, %xmm7 + + vmovdqa %xmm7, %xmm0 + vpand mask2(%rip), %xmm0, %xmm0 + vpsrldq $12, %xmm7, %xmm7 + vpclmulqdq $0x10, %xmm10, %xmm7, %xmm7 + vpxor %xmm0, %xmm7, %xmm7 + + /* barrett reduction */ +.barrett: + vmovdqa rk7(%rip), %xmm10 + vmovdqa %xmm7, %xmm0 + vpclmulqdq $0x01, %xmm10, %xmm7, %xmm7 + vpslldq $4, %xmm7, %xmm7 + vpclmulqdq $0x11, %xmm10, %xmm7, %xmm7 + + vpslldq $4, %xmm7, %xmm7 + vpxor %xmm0, %xmm7, %xmm7 + vpextrd $1, %xmm7, %eax + +.cleanup: + /* scale the result back to 16 bits. */ + shr $16, %eax + add $(VARIABLE_OFFSET), %rsp + ret + +.align 16 +.less_than_256: + /* check if there is enough buffer to be able to fold 16B at a time. */ + cmp $32, len + jl .less_than_32 + + /* If there is, load the constants. */ + vmovdqa rk1(%rip), %xmm10 + + /* + * get the initial crc value and align it to its correct place. + * And load the plaintext and byte-reflect it. + */ + vmovd init_crc, %xmm0 + vpslldq $12, %xmm0, %xmm0 + vmovdqu (buf), %xmm7 + vpshufb %xmm18, %xmm7, %xmm7 + vpxor %xmm0, %xmm7, %xmm7 + + /* update the buffer pointer */ + add $16, buf + + /* subtract 32 instead of 16 to save one instruction from the loop */ + sub $32, len + + jmp .16B_reduction_loop + +.align 16 +.less_than_32: + /* + * mov initial crc to the return value. This is necessary for + * zero-length buffers. + */ + mov init_crc, %eax + test len, len + je .cleanup + + vmovd init_crc, %xmm0 + vpslldq $12, %xmm0, %xmm0 + + cmp $16, len + je .exact_16_left + jl .less_than_16_left + + vmovdqu (buf), %xmm7 + vpshufb %xmm18, %xmm7, %xmm7 + vpxor %xmm0, %xmm7, %xmm7 + add $16, buf + sub $16, len + vmovdqa rk1(%rip), %xmm10 + jmp .get_last_two_xmms + +.align 16 +.less_than_16_left: + /* + * use stack space to load data less than 16 bytes, zero-out the 16B + * in the memory first. + */ + vpxor %xmm1, %xmm1, %xmm1 + mov %rsp, %r11 + vmovdqa %xmm1, (%r11) + + cmp $4, len + jl .only_less_than_4 + + mov len, %r9 + cmp $8, len + jl .less_than_8_left + + mov (buf), %rax + mov %rax, (%r11) + add $8, %r11 + sub $8, len + add $8, buf +.less_than_8_left: + cmp $4, len + jl .less_than_4_left + + mov (buf), %eax + mov %eax, (%r11) + add $4, %r11 + sub $4, len + add $4, buf + +.less_than_4_left: + cmp $2, len + jl .less_than_2_left + + mov (buf), %ax + mov %ax, (%r11) + add $2, %r11 + sub $2, len + add $2, buf +.less_than_2_left: + cmp $1, len + jl .zero_left + + mov (buf), %al + mov %al, (%r11) + +.zero_left: + vmovdqa (%rsp), %xmm7 + vpshufb %xmm18, %xmm7, %xmm7 + vpxor %xmm0, %xmm7, %xmm7 + + lea 16 + pshufb_shf_table(%rip), %rax + sub %r9, %rax + vmovdqu (%rax), %xmm0 + vpxor mask1(%rip), %xmm0, %xmm0 + + vpshufb %xmm0,%xmm7, %xmm7 + jmp .128_done + +.align 16 +.exact_16_left: + vmovdqu (buf), %xmm7 + vpshufb %xmm18, %xmm7, %xmm7 + vpxor %xmm0, %xmm7, %xmm7 + jmp .128_done + +.only_less_than_4: + cmp $3, len + jl .only_less_than_3 + + mov (buf), %al + mov %al, (%r11) + + mov 1(buf), %al + mov %al, 1(%r11) + + mov 2(buf), %al + mov %al, 2(%r11) + + vmovdqa (%rsp), %xmm7 + vpshufb %xmm18, %xmm7, %xmm7 + vpxor %xmm0, %xmm7, %xmm7 + + vpsrldq $5, %xmm7, %xmm7 + jmp .barrett + +.only_less_than_3: + cmp $2, len + jl .only_less_than_2 + + mov (buf), %al + mov %al, (%r11) + + mov 1(buf), %al + mov %al, 1(%r11) + + vmovdqa (%rsp), %xmm7 + vpshufb %xmm18, %xmm7, %xmm7 + vpxor %xmm0, %xmm7, %xmm7 + + vpsrldq $6, %xmm7, %xmm7 + jmp .barrett + +.only_less_than_2: + mov (buf), %al + mov %al, (%r11) + + vmovdqa (%rsp), %xmm7 + vpshufb %xmm18, %xmm7, %xmm7 + vpxor %xmm0, %xmm7, %xmm7 + + vpsrldq $7, %xmm7, %xmm7 + jmp .barrett +SYM_FUNC_END(crct10dif_pcl_avx512) + +.section .data +.align 32 +rk_1: .quad 0xdccf000000000000 +rk_2: .quad 0x4b0b000000000000 +rk1: .quad 0x2d56000000000000 +rk2: .quad 0x06df000000000000 +rk3: .quad 0x9d9d000000000000 +rk4: .quad 0x7cf5000000000000 +rk5: .quad 0x2d56000000000000 +rk6: .quad 0x1368000000000000 +rk7: .quad 0x00000001f65a57f8 +rk8: .quad 0x000000018bb70000 +rk9: .quad 0xceae000000000000 +rk10: .quad 0xbfd6000000000000 +rk11: .quad 0x1e16000000000000 +rk12: .quad 0x713c000000000000 +rk13: .quad 0xf7f9000000000000 +rk14: .quad 0x80a6000000000000 +rk15: .quad 0x044c000000000000 +rk16: .quad 0xe658000000000000 +rk17: .quad 0xad18000000000000 +rk18: .quad 0xa497000000000000 +rk19: .quad 0x6ee3000000000000 +rk20: .quad 0xe7b5000000000000 +rk_1b: .quad 0x2d56000000000000 +rk_2b: .quad 0x06df000000000000 + .quad 0x0000000000000000 + .quad 0x0000000000000000 + +.align 16 +mask1: + .octa 0x80808080808080808080808080808080 + +.align 16 +mask2: + .octa 0x00000000FFFFFFFFFFFFFFFFFFFFFFFF + +.align 16 +SHUF_MASK: + .octa 0x000102030405060708090A0B0C0D0E0F + +.align 16 +pshufb_shf_table: .octa 0x8f8e8d8c8b8a89888786858483828100 + .octa 0x000e0d0c0b0a09080706050403020100 + .octa 0x0f0e0d0c0b0a09088080808080808080 + .octa 0x80808080808080808080808080808080 diff --git a/arch/x86/crypto/crct10dif-pclmul_glue.c b/arch/x86/crypto/crct10dif-pclmul_glue.c index 71291d5a..26a6350 100644 --- a/arch/x86/crypto/crct10dif-pclmul_glue.c +++ b/arch/x86/crypto/crct10dif-pclmul_glue.c @@ -35,6 +35,16 @@ #include <asm/simd.h> asmlinkage u16 crc_t10dif_pcl(u16 init_crc, const u8 *buf, size_t len); +#ifdef CONFIG_CRYPTO_CRCT10DIF_AVX512 +asmlinkage u16 crct10dif_pcl_avx512(u16 init_crc, const u8 *buf, size_t len); +#else +static u16 crct10dif_pcl_avx512(u16 init_crc, const u8 *buf, size_t len) +{ return 0; } +#endif + +static bool use_avx512; +module_param(use_avx512, bool, 0644); +MODULE_PARM_DESC(use_avx512, "Use AVX512 optimized algorithm, if available"); struct chksum_desc_ctx { __u16 crc; @@ -56,7 +66,12 @@ static int chksum_update(struct shash_desc *desc, const u8 *data, if (length >= 16 && crypto_simd_usable()) { kernel_fpu_begin(); - ctx->crc = crc_t10dif_pcl(ctx->crc, data, length); + if (IS_ENABLED(CONFIG_CRYPTO_CRCT10DIF_AVX512) && + cpu_feature_enabled(X86_FEATURE_VPCLMULQDQ) && + use_avx512) + ctx->crc = crct10dif_pcl_avx512(ctx->crc, data, length); + else + ctx->crc = crc_t10dif_pcl(ctx->crc, data, length); kernel_fpu_end(); } else ctx->crc = crc_t10dif_generic(ctx->crc, data, length); @@ -75,7 +90,12 @@ static int __chksum_finup(__u16 crc, const u8 *data, unsigned int len, u8 *out) { if (len >= 16 && crypto_simd_usable()) { kernel_fpu_begin(); - *(__u16 *)out = crc_t10dif_pcl(crc, data, len); + if (IS_ENABLED(CONFIG_CRYPTO_CRCT10DIF_AVX512) && + cpu_feature_enabled(X86_FEATURE_VPCLMULQDQ) && + use_avx512) + *(__u16 *)out = crct10dif_pcl_avx512(crc, data, len); + else + *(__u16 *)out = crc_t10dif_pcl(crc, data, len); kernel_fpu_end(); } else *(__u16 *)out = crc_t10dif_generic(crc, data, len); diff --git a/arch/x86/include/asm/disabled-features.h b/arch/x86/include/asm/disabled-features.h index 5861d34..1192dea 100644 --- a/arch/x86/include/asm/disabled-features.h +++ b/arch/x86/include/asm/disabled-features.h @@ -56,6 +56,12 @@ # define DISABLE_PTI (1 << (X86_FEATURE_PTI & 31)) #endif +#if defined(CONFIG_AS_VPCLMULQDQ) +# define DISABLE_VPCLMULQDQ 0 +#else +# define DISABLE_VPCLMULQDQ (1 << (X86_FEATURE_VPCLMULQDQ & 31)) +#endif + #ifdef CONFIG_IOMMU_SUPPORT # define DISABLE_ENQCMD 0 #else @@ -82,7 +88,7 @@ #define DISABLED_MASK14 0 #define DISABLED_MASK15 0 #define DISABLED_MASK16 (DISABLE_PKU|DISABLE_OSPKE|DISABLE_LA57|DISABLE_UMIP| \ - DISABLE_ENQCMD) + DISABLE_ENQCMD|DISABLE_VPCLMULQDQ) #define DISABLED_MASK17 0 #define DISABLED_MASK18 0 #define DISABLED_MASK_CHECK BUILD_BUG_ON_ZERO(NCAPINTS != 19) diff --git a/crypto/Kconfig b/crypto/Kconfig index a367fcf..b090f14 100644 --- a/crypto/Kconfig +++ b/crypto/Kconfig @@ -613,6 +613,29 @@ config CRYPTO_CRC32C_VPMSUM (vpmsum) instructions, introduced in POWER8. Enable on POWER8 and newer processors for improved performance. +config CRYPTO_AVX512 + bool "AVX512 hardware acceleration for crypto algorithms" + depends on X86 + depends on 64BIT + help + This option will compile in AVX512 hardware accelerated crypto + algorithms. These optimized algorithms provide substantial(2-10x) + improvements over existing crypto algorithms for large data size. + However, it may also incur a frequency penalty (aka. "bin drops") + and cause collateral damage to other workloads running on the + same core. + +# We default CRYPTO_CRCT10DIF_AVX512 to Y but depend on CRYPTO_AVX512 in +# order to have a singular option (CRYPTO_AVX512) select multiple algorithms +# when supported. Specifically, if the platform and/or toolset does not +# support VPLMULQDQ. Then this algorithm should not be supported as part of +# the set that CRYPTO_AVX512 selects. +config CRYPTO_CRCT10DIF_AVX512 + bool + default y + depends on CRYPTO_AVX512 + depends on CRYPTO_CRCT10DIF_PCLMUL + depends on AS_VPCLMULQDQ config CRYPTO_CRC32C_SPARC64 tristate "CRC32c CRC algorithm (SPARC64)" -- 2.7.4
