> -----Original Message----- > From: Ard Biesheuvel <ard.biesheuvel@xxxxxxxxxx> > Sent: Friday, August 9, 2019 7:49 PM > To: Horia Geanta <horia.geanta@xxxxxxx> > Cc: Herbert Xu <herbert@xxxxxxxxxxxxxxxxxxx>; Pascal Van Leeuwen > <pvanleeuwen@xxxxxxxxxxxxxx>; Milan Broz <gmazyland@xxxxxxxxx>; dm-devel@xxxxxxxxxx; linux- > crypto@xxxxxxxxxxxxxxx > Subject: Re: [dm-devel] xts fuzz testing and lack of ciphertext stealing support > > On Fri, 9 Aug 2019 at 10:44, Horia Geanta <horia.geanta@xxxxxxx> wrote: > > > > On 8/9/2019 9:45 AM, Ard Biesheuvel wrote: > > > On Fri, 9 Aug 2019 at 05:48, Herbert Xu <herbert@xxxxxxxxxxxxxxxxxxx> wrote: > > >> > > >> On Thu, Aug 08, 2019 at 06:01:49PM +0000, Horia Geanta wrote: > > >>> > > >>> -- >8 -- > > >>> > > >>> Subject: [PATCH] crypto: testmgr - Add additional AES-XTS vectors for covering > > >>> CTS (part II) > > >> > > >> Patchwork doesn't like it when you do this and it'll discard > > >> your patch. To make it into patchwork you need to put the new > > >> Subject in the email headers. > > >> > > > > > > IMO, pretending that your XTS implementation is compliant by only > > I've never said that. > > Some parts are compliant, some are not. > > > > > providing test vectors with the last 8 bytes of IV cleared is not the > > > right fix for this issue. If you want to be compliant, you will need > > It's not a fix. > > It's adding test vectors which are not provided in the P1619 standard, > > where "data unit sequence number" is at most 5B. > > > > Indeed. But I would prefer not to limit ourselves to 5 bytes of sector > numbers in the test vectors. However, we should obviously not add test > vectors that are known to cause breakages on hardware that works fine > in practice. > Well, obviously, the full 16 byte sector number vectors fail on existing CAAM hardware, which I do assume to work fine in practice. And you know I'm not in favor of building all kinds of workarounds into the drivers. Fact is, we know there are no current users that need more than 64 bits of IV. Fact is also that having 64 bits of IV in the vectors is already an improvement over the 40 bits in the original vectors. And unlike CTS, I am not aware of any real use case for more than 64 bits. Finally, another fact is that limiting the *vectors* to 64 bits of IV does not prohibit anyone from *using* a full 128 bit IV on an implementation that *does* support this. I would think most users of XTS, like dmcrypt, would allow you to specify the cra_drivername explictly anyway, so just don't select legacy CAAM if you need that. (heck, if it would be reading and writing its own data, and not need compatibility with other implementations, it wouldn't even matter) So yes, the specs are quite clear on the sector number being a full 128 bits. But that doesn't prevent us from specifying that the crypto API implementation currently only supports 64 bits, with the remaining bits being forced to 0. We can always revisit that when an actual use case for more than 64 bits arises ... > > > to provide a s/w fallback for these cases. > > > > > Yes, the plan is to: > > > > -add 16B IV support for caam versions supporting it - caam Era 9+, > > currently deployed in lx2160a and ls108a > > > > -remove current 8B IV support and add s/w fallback for affected caam versions > > I'd assume this could be done dynamically, i.e. depending on IV provided > > in the crypto request to use either the caam engine or s/w fallback. > > > > Yes. If the IV received from the caller has bytes 8..15 cleared, you > use the limited XTS h/w implementation, otherwise you fall back to > xts(ecb-aes-caam..). Regards, Pascal van Leeuwen Silicon IP Architect, Multi-Protocol Engines @ Verimatrix www.insidesecure.com
