On 06/01/2018 12:41 AM, Stewart Smith wrote:
> Haren Myneni <haren@xxxxxxxxxxxxxxxxxx> writes:
>> NX increments readOffset by FIFO size in receive FIFO control register
>> when CRB is read. But the index in RxFIFO has to match with the
>> corresponding entry in FIFO maintained by VAS in kernel. Otherwise NX
>> may be processing incorrect CRBs and can cause CRB timeout.
>>
>> VAS FIFO offset is 0 when the receive window is opened during
>> initialization. When the module is reloaded or in kexec boot, readOffset
>> in FIFO control register may not match with VAS entry. This patch adds
>> nx_coproc_init OPAL call to reset readOffset and queued entries in FIFO
>> control register for both high and normal FIFOs.
>>
>> Signed-off-by: Haren Myneni <haren@xxxxxxxxxx>
>>
>> diff --git a/arch/powerpc/include/asm/opal-api.h b/arch/powerpc/include/asm/opal-api.h
>> index d886a5b..ff61e4b 100644
>> --- a/arch/powerpc/include/asm/opal-api.h
>> +++ b/arch/powerpc/include/asm/opal-api.h
>> @@ -206,7 +206,8 @@
>> #define OPAL_NPU_TL_SET 161
>> #define OPAL_PCI_GET_PBCQ_TUNNEL_BAR 164
>> #define OPAL_PCI_SET_PBCQ_TUNNEL_BAR 165
>> -#define OPAL_LAST 165
>> +#define OPAL_NX_COPROC_INIT 167
>> +#define OPAL_LAST 167
>>
>> /* Device tree flags */
>>
>> diff --git a/arch/powerpc/include/asm/opal.h b/arch/powerpc/include/asm/opal.h
>> index 7159e1a..d79eb82 100644
>> --- a/arch/powerpc/include/asm/opal.h
>> +++ b/arch/powerpc/include/asm/opal.h
>> @@ -288,6 +288,7 @@ int64_t opal_imc_counters_init(uint32_t type, uint64_t address,
>> int opal_get_power_shift_ratio(u32 handle, int token, u32 *psr);
>> int opal_set_power_shift_ratio(u32 handle, int token, u32 psr);
>> int opal_sensor_group_clear(u32 group_hndl, int token);
>> +int opal_nx_coproc_init(uint32_t chip_id, uint32_t ct);
>>
>> s64 opal_signal_system_reset(s32 cpu);
>>
>> diff --git a/arch/powerpc/platforms/powernv/opal-wrappers.S b/arch/powerpc/platforms/powernv/opal-wrappers.S
>> index 3da30c2..c7541a9 100644
>> --- a/arch/powerpc/platforms/powernv/opal-wrappers.S
>> +++ b/arch/powerpc/platforms/powernv/opal-wrappers.S
>> @@ -325,3 +325,4 @@ OPAL_CALL(opal_npu_spa_clear_cache, OPAL_NPU_SPA_CLEAR_CACHE);
>> OPAL_CALL(opal_npu_tl_set, OPAL_NPU_TL_SET);
>> OPAL_CALL(opal_pci_get_pbcq_tunnel_bar, OPAL_PCI_GET_PBCQ_TUNNEL_BAR);
>> OPAL_CALL(opal_pci_set_pbcq_tunnel_bar, OPAL_PCI_SET_PBCQ_TUNNEL_BAR);
>> +OPAL_CALL(opal_nx_coproc_init, OPAL_NX_COPROC_INIT);
>> diff --git a/arch/powerpc/platforms/powernv/opal.c b/arch/powerpc/platforms/powernv/opal.c
>> index 48fbb41..5e13908 100644
>> --- a/arch/powerpc/platforms/powernv/opal.c
>> +++ b/arch/powerpc/platforms/powernv/opal.c
>> @@ -1035,3 +1035,5 @@ void powernv_set_nmmu_ptcr(unsigned long ptcr)
>> EXPORT_SYMBOL_GPL(opal_int_set_mfrr);
>> EXPORT_SYMBOL_GPL(opal_int_eoi);
>> EXPORT_SYMBOL_GPL(opal_error_code);
>> +/* Export the below symbol for NX compression */
>> +EXPORT_SYMBOL(opal_nx_coproc_init);
>> diff --git a/drivers/crypto/nx/nx-842-powernv.c b/drivers/crypto/nx/nx-842-powernv.c
>> index 1e87637..6c4784d 100644
>> --- a/drivers/crypto/nx/nx-842-powernv.c
>> +++ b/drivers/crypto/nx/nx-842-powernv.c
>> @@ -24,6 +24,8 @@
>> #include <asm/icswx.h>
>> #include <asm/vas.h>
>> #include <asm/reg.h>
>> +#include <asm/opal-api.h>
>> +#include <asm/opal.h>
>>
>> MODULE_LICENSE("GPL");
>> MODULE_AUTHOR("Dan Streetman <ddstreet@xxxxxxxx>");
>> @@ -803,9 +805,26 @@ static int __init vas_cfg_coproc_info(struct device_node *dn, int chip_id,
>> if (!coproc)
>> return -ENOMEM;
>>
>> - if (!strcmp(priority, "High"))
>> + if (!strcmp(priority, "High")) {
>> + /*
>> + * (lpid, pid, tid) combination has to be unique for each
>> + * coprocessor instance in the system. So to make it
>> + * unique, skiboot uses coprocessor type such as 842 or
>> + * GZIP for pid and provides this value to kernel in pid
>> + * device-tree property.
>> + *
>> + * Initialize each NX instance for both high and normal
>> + * priority FIFOs.
>> + */
>> + ret = opal_nx_coproc_init(chip_id, pid);
>> + if (ret) {
>> + pr_err("Failed to initialize NX coproc: %d\n", ret);
>> + ret = opal_error_code(ret);
>> + goto err_out;
>> + }
>> +
>> coproc->ct = VAS_COP_TYPE_842_HIPRI;
>
> I think this should be called for all priority queues as it would be at
> least theoretically possible to only have Normal priority queues, in
> which case this patch wouldn't fix the problem.
device tree exports separate nodes for high and normal priority FIFOs per each NX instance. But NX init OPAL function is called once per each NX instance when high-FIFO device node is parsed to reset high and normal FIFO control registers. As you see in skiboot patch, resets both priority registers. Thought we should minimize the number of OPAL calla execution and also should have generic NX init OPAL call. We can extend this call to reset default values for any other registers if needed.
If you prefer calling separately based on priority, we can have opal_nx_coproc_FIFO_init(chip_id, pid, priority). Please let me know.
Thanks
Haren
>
>
