timenhhf wrote: > hi, > thanks for your reply. > the attached file is the microcode file included in CSR2.4 crypto > package that i got from INTEL's FAE. > And the crypto function supported or not isn't really what i'm concern > now, because after I startup the NPE module, the network can't work well. > the detail steps as followed: > (1)gcc -Wall IxNpeMicrocode.c -o IxNpeMicrocode Which image are you specificing in the .h? I currently use IX_NPEDL_NPEIMAGE_NPEC_CRYPTO_AES_ETH_LEARN_FILTER_FIREWALL and IX_NPEDL_NPEIMAGE_NPEB_ETH_SPAN_FIREWALL_VLAN_QOS_HDR_CONV > (2)./IxNpeMicrocode (get NPE-B & NPE-C) > (3)cp NPEs to /lib/firmware : cp -a NPE-* /lib/firmware/ > (4)Make ixp425's ramdisk.gz package > (5)after system startup, do: > echo "/sbin/mdev" > /proc/sys/kernel/hotplug > /sbin/mdev -s You should see the busybox doc. I do: mount -t proc proc /proc mount -t tmpfs -o size=64K mdev /dev mkdir /dev/pts mount -t devpts devpts /dev/pts mount -t sysfs sysfs /sys echo /sbin/mdev > /proc/sys/kernel/hotplug mdev -s > (6)insmod the NPE modules: > modprobe ixp4xx_eth > IXP4xx Queue Manager initialized. > eth0: MII PHY 0 on NPE-B > eth1: MII PHY 1 on NPE-C if you modprobe ixp4xx_crypto does it come up? > (7)lsmod to check: > Module Size Used by Not tainted > ixp4xx_eth 12824 0 > ixp4xx_npe 7200 3 ixp4xx_eth > ixp4xx_qmgr 4824 1 ixp4xx_eth > (8)set the NPE MAC address: > ifconfig eth0 hw ether 00:03:05:06:07:08 > (9)ifconfig eth0 192.168.1.1 netmask 255.255.255.0 perhaps "ip link set eth0 up" > (10) ping the NPE own interface: > # ping -c 1 192.168.1.11 > PING 192.168.1.11 (192.168.1.11): 56 data bytes > 64 bytes from 192.168.1.11: seq=0 ttl=64 time=0.539 ms > (11)ping -c 1 192.168.1.98 (192.168.1.98 is the PC's ip address) > PING 192.168.1.98 (192.168.1.98): 56 data bytes > --- 192.168.1.98 ping statistics --- > 1 packets transmitted, 0 packets received, 100% packet loss > (12)check the interface status > # ifconfig > eth0 Link encap:Ethernet HWaddr 00:01:03:08:01:02 > inet addr:192.168.1.11 Bcast:192.168.1.255 Mask:255.255.255.0 > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:3 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:100 > RX bytes:0 (0.0 B) TX bytes:126 (126.0 B) > Comments? thank you very much. What does "ip link" and "ip addr" show? perhaps send the entire "dmesg" it should contain info if the NPE is starting up correctly. -- -- Karl Hiramoto http://karl.hiramoto.org/ -- To unsubscribe from this list: send the line "unsubscribe linux-crypto" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
