> Subject: Re: [Patch v2 3/6] cifs: smbd: Avoid allocating iov on the stack
>
> Didn't see any obvious problems, but can you fix the checkpatch warnings
> and resend to the list (I am more concerned about the last two warnings
> rather than the first one).
Yes, I will fix it and resend.
>
> $ scripts/checkpatch.pl 0001-cifs-smbd-Avoid-allocating-iov-on-the-
> stack.patch
> WARNING: line over 80 characters
> #60: FILE: fs/cifs/smbdirect.c:2106:
> + log_write(ERR, "expected the pdu length in 1st iov, but got
> 0x%lu\n", rqst->rq_iov[0].iov_len);
>
> ERROR: Prefixing 0x with decimal output is defective
> #60: FILE: fs/cifs/smbdirect.c:2106:
> + log_write(ERR, "expected the pdu length in 1st iov, but got
> 0x%lu\n", rqst->rq_iov[0].iov_len);
>
> WARNING: braces {} are not necessary for single statement blocks
> #69: FILE: fs/cifs/smbdirect.c:2112:
> + for (i = 0; i < rqst->rq_nvec-1; i++) {
> buflen += iov[i].iov_len;
> }
>
> total: 1 errors, 2 warnings, 65 lines checked
>
> NOTE: For some of the reported defects, checkpatch may be able to
> mechanically convert to the typical style using --fix or --fix-inplace.
>
> 0001-cifs-smbd-Avoid-allocating-iov-on-the-stack.patch has style problems,
> please review.
>
> On Tue, Apr 17, 2018 at 2:17 PM, Long Li <longli@xxxxxxxxxxxxxxxxx> wrote:
> > From: Long Li <longli@xxxxxxxxxxxxx>
> >
> > It's not necessary to allocate another iov when going through the
> > buffers in smbd_send() through RDMA send.
> >
> > Remove it to reduce stack size.
> >
> > Signed-off-by: Long Li <longli@xxxxxxxxxxxxx>
> > Cc: stable@xxxxxxxxxxxxxxx
> > ---
> > fs/cifs/smbdirect.c | 36 ++++++++++++------------------------
> > 1 file changed, 12 insertions(+), 24 deletions(-)
> >
> > diff --git a/fs/cifs/smbdirect.c b/fs/cifs/smbdirect.c index
> > b5c6c0d..f575e9a 100644
> > --- a/fs/cifs/smbdirect.c
> > +++ b/fs/cifs/smbdirect.c
> > @@ -2088,7 +2088,7 @@ int smbd_send(struct smbd_connection *info,
> struct smb_rqst *rqst)
> > int start, i, j;
> > int max_iov_size =
> > info->max_send_size - sizeof(struct smbd_data_transfer);
> > - struct kvec iov[SMBDIRECT_MAX_SGE];
> > + struct kvec *iov;
> > int rc;
> >
> > info->smbd_send_pending++;
> > @@ -2099,32 +2099,20 @@ int smbd_send(struct smbd_connection *info,
> struct smb_rqst *rqst)
> > }
> >
> > /*
> > - * This usually means a configuration error
> > - * We use RDMA read/write for packet size >
> rdma_readwrite_threshold
> > - * as long as it's properly configured we should never get into this
> > - * situation
> > - */
> > - if (rqst->rq_nvec + rqst->rq_npages > SMBDIRECT_MAX_SGE) {
> > - log_write(ERR, "maximum send segment %x exceeding %x\n",
> > - rqst->rq_nvec + rqst->rq_npages, SMBDIRECT_MAX_SGE);
> > - rc = -EINVAL;
> > - goto done;
> > - }
> > -
> > - /*
> > - * Remove the RFC1002 length defined in MS-SMB2 section 2.1
> > - * It is used only for TCP transport
> > + * Skip the RFC1002 length defined in MS-SMB2 section 2.1
> > + * It is used only for TCP transport in the iov[0]
> > * In future we may want to add a transport layer under protocol
> > * layer so this will only be issued to TCP transport
> > */
> > - iov[0].iov_base = (char *)rqst->rq_iov[0].iov_base + 4;
> > - iov[0].iov_len = rqst->rq_iov[0].iov_len - 4;
> > - buflen += iov[0].iov_len;
> > +
> > + if (rqst->rq_iov[0].iov_len != 4) {
> > + log_write(ERR, "expected the pdu length in 1st iov, but got
> 0x%lu\n", rqst->rq_iov[0].iov_len);
> > + return -EINVAL;
> > + }
> > + iov = &rqst->rq_iov[1];
> >
> > /* total up iov array first */
> > - for (i = 1; i < rqst->rq_nvec; i++) {
> > - iov[i].iov_base = rqst->rq_iov[i].iov_base;
> > - iov[i].iov_len = rqst->rq_iov[i].iov_len;
> > + for (i = 0; i < rqst->rq_nvec-1; i++) {
> > buflen += iov[i].iov_len;
> > }
> >
> > @@ -2197,14 +2185,14 @@ int smbd_send(struct smbd_connection *info,
> struct smb_rqst *rqst)
> > goto done;
> > }
> > i++;
> > - if (i == rqst->rq_nvec)
> > + if (i == rqst->rq_nvec-1)
> > break;
> > }
> > start = i;
> > buflen = 0;
> > } else {
> > i++;
> > - if (i == rqst->rq_nvec) {
> > + if (i == rqst->rq_nvec-1) {
> > /* send out all remaining vecs */
> > remaining_data_length -= buflen;
> > log_write(INFO,
> > --
> > 2.7.4
> >
> > --
> > To unsubscribe from this list: send the line "unsubscribe linux-cifs"
> > in the body of a message to majordomo@xxxxxxxxxxxxxxx More
> majordomo
> > info at
> >
> https://na01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fvger.k
> > ernel.org%2Fmajordomo-
> info.html&data=02%7C01%7Clongli%40microsoft.com%
> >
> 7C23fbdbb0598a497f624708d5a92f6435%7C72f988bf86f141af91ab2d7cd011d
> b47%
> >
> 7C1%7C0%7C636600943380887988&sdata=imh9cWDQQEXqxHdUrCuEykgiLfKs
> UAl20jB
> > yPOS7FrI%3D&reserved=0
>
>
>
> --
> Thanks,
>
> Steve
> --
> To unsubscribe from this list: send the line "unsubscribe linux-cifs" in the
> body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at
> https://na01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fvger.ke
> rnel.org%2Fmajordomo-
> info.html&data=02%7C01%7Clongli%40microsoft.com%7C23fbdbb0598a497f
> 624708d5a92f6435%7C72f988bf86f141af91ab2d7cd011db47%7C1%7C0%7C63
> 6600943380887988&sdata=imh9cWDQQEXqxHdUrCuEykgiLfKsUAl20jByPOS7F
> rI%3D&reserved=0
��.n��������+%������w��{.n�����{�����ܨ}���Ơz�j:+v�����w����ޙ��&�)ߡ�a����z�ޗ���ݢj��w�f
