Hi, v2 -- In v2 I mostly fixed error handling in this series and rebased to v6.11-rc1. I also dropped the omap serial series for Partial-IO as it can't be tested with Partial-IO at the moment. The code was tested with other low power modes but they will be upstreamed later on. Series ------ am62, am62a and am62p support Partial-IO, a poweroff SoC state with a few pin groups being active for wakeup. To support mcu_mcan0 and mcu_mcan1 wakeup for the mentioned SoCs, the series introduces a notion of wake-on-lan for m_can. If the user decides to enable wake-on-lan for a m_can device, the device is set to wakeup enabled. A 'wakeup' pinctrl state is selected to enable wakeup flags for the relevant pins. If wake-on-lan is disabled the default pinctrl is selected. It is based on v6.11-rc1 with this series applied: https://lore.kernel.org/lkml/20240726195944.2414812-1-msp@xxxxxxxxxxxx/ Also available at https://gitlab.baylibre.com/msp8/linux/-/tree/topic/mcan-fixes/v6.11?ref_type=heads Partial-IO ---------- This series is part of a bigger topic to support Partial-IO on am62, am62a and am62p. Partial-IO is a poweroff state in which some pins are able to wakeup the SoC. In detail MCU m_can and two serial port pins can trigger the wakeup. A documentation can also be found in section 6.2.4 in the TRM: https://www.ti.com/lit/pdf/spruiv7 This other series is relevant for the support of Partial-IO: - firmware: ti_sci: Partial-IO support https://gitlab.baylibre.com/msp8/linux/-/tree/topic/am62-partialio/v6.11?ref_type=heads Testing ------- A test branch is available here that includes all patches required to test Partial-IO: https://gitlab.baylibre.com/msp8/linux/-/tree/integration/am62-lp-sk-partialio/v6.11?ref_type=heads After enabling Wake-on-LAN the system can be powered off and will enter the Partial-IO state in which it can be woken up by activity on the specific pins: ethtool -s can0 wol p ethtool -s can1 wol p poweroff I tested these patches on am62-lp-sk. Best, Markus Previous versions: v1: https://lore.kernel.org/lkml/20240523075347.1282395-1-msp@xxxxxxxxxxxx/ Changes in v2: - Rebase to v6.11-rc1 - Squash these two patches for the binding into one: dt-bindings: can: m_can: Add wakeup-source property dt-bindings: can: m_can: Add wakeup pinctrl state - Add error handling to multiple patches of the m_can driver - Add error handling in m_can_class_allocate_dev(). This also required to add a new patch to return error pointers from m_can_class_allocate_dev(). Markus Schneider-Pargmann (6): dt-bindings: can: m_can: Add wakeup properties can: m_can: Map WoL to device_set_wakeup_enable can: m_can: Return ERR_PTR on error in allocation can: m_can: Support pinctrl wakeup state arm64: dts: ti: k3-am62: Mark mcu_mcan0/1 as wakeup-source arm64: dts: ti: k3-am62a-mcu: Mark mcu_mcan0/1 as wakeup-source Vibhore Vardhan (1): arm64: dts: ti: k3-am62p-mcu: Mark mcu_mcan0/1 as wakeup-source .../bindings/net/can/bosch,m_can.yaml | 20 ++++ arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi | 2 + arch/arm64/boot/dts/ti/k3-am62a-mcu.dtsi | 2 + .../dts/ti/k3-am62p-j722s-common-mcu.dtsi | 2 + drivers/net/can/m_can/m_can.c | 100 +++++++++++++++++- drivers/net/can/m_can/m_can.h | 4 + drivers/net/can/m_can/m_can_pci.c | 4 +- drivers/net/can/m_can/m_can_platform.c | 4 +- drivers/net/can/m_can/tcan4x5x-core.c | 4 +- 9 files changed, 133 insertions(+), 9 deletions(-) -- 2.45.2
