Hi Peter, The patch is getting better. But there are a lot of u8 * buffers I would like to get rid of. On Tue. 13 Apr 2023 at 17:42, Ji-Ze Hong (Peter Hong) <peter_hong@xxxxxxxxxxxxx> wrote: > This patch adds support for Fintek USB to 2CAN controller. > > Signed-off-by: Ji-Ze Hong (Peter Hong) <peter_hong@xxxxxxxxxxxxx> > --- > Changelog: > v4: > 1. Remove f81604_prepare_urbs/f81604_remove_urbs() and alloc URB/buffer > dynamically in f81604_register_urbs(), using "urbs_anchor" for manage > all rx/int URBs. > 2. Add F81604 to MAINTAINERS list. > 3. Change handle_clear_reg_work/handle_clear_overrun_work to single > clear_reg_work and using bitwise "clear_flags" to record it. > 4. Move __f81604_set_termination in front of f81604_probe() to avoid > rarely racing condition. > 5. Add __aligned to struct f81604_int_data / f81604_sff / f81604_eff. > 6. Add aligned operations in f81604_start_xmit/f81604_process_rx_packet(). > 7. Change lots of CANBUS functions first parameter from struct usb_device* > to struct f81604_port_priv *priv. But remain f81604_write / f81604_read > / f81604_update_bits() as struct usb_device* for > __f81604_set_termination() in probe() stage. > 8. Simplify f81604_read_int_callback() and separate into > f81604_handle_tx / f81604_handle_can_bus_errors() functions. > > v3: > 1. Change CAN clock to using MEGA units. > 2. Remove USB set/get retry, only remain SJA1000 reset/operation retry. > 3. Fix all numberic constant to define. > 4. Add terminator control. (only 0 & 120 ohm) > 5. Using struct data to represent INT/TX/RX endpoints data instead byte > arrays. > 6. Error message reports changed from %d to %pe for mnemotechnic values. > 7. Some bit operations are changed to FIELD_PREP(). > 8. Separate TX functions from f81604_read_int_callback(). > 9. cf->can_id |= CAN_ERR_CNT in f81604_read_int_callback to report valid > TX/RX error counts. > 10. Move f81604_prepare_urbs/f81604_remove_urbs() from CAN open/close() to > USB probe/disconnect(). > 11. coding style refactoring. > > v2: > 1. coding style refactoring. > 2. some const number are defined to describe itself. > 3. fix wrong usage for can_get_echo_skb() in f81604_write_bulk_callback(). > > MAINTAINERS | 6 + > drivers/net/can/usb/Kconfig | 12 + > drivers/net/can/usb/Makefile | 1 + > drivers/net/can/usb/f81604.c | 1221 ++++++++++++++++++++++++++++++++++ > 4 files changed, 1240 insertions(+) > create mode 100644 drivers/net/can/usb/f81604.c > > diff --git a/MAINTAINERS b/MAINTAINERS > index f375bbf3bc80..fa573f637c2f 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -8058,6 +8058,12 @@ S: Maintained > F: drivers/hwmon/f75375s.c > F: include/linux/f75375s.h > > +FINTEK F81604 USB to 2xCANBUS DEVICE DRIVER > +M: Ji-Ze Hong (Peter Hong) <peter_hong@xxxxxxxxxxxxx> > +L: linux-can@xxxxxxxxxxxxxxx > +S: Maintained > +F: drivers/net/can/usb/f81604.c > + > FIREWIRE AUDIO DRIVERS and IEC 61883-1/6 PACKET STREAMING ENGINE > M: Clemens Ladisch <clemens@xxxxxxxxxx> > M: Takashi Sakamoto <o-takashi@xxxxxxxxxxxxx> > diff --git a/drivers/net/can/usb/Kconfig b/drivers/net/can/usb/Kconfig > index 445504ababce..58fcd2b34820 100644 > --- a/drivers/net/can/usb/Kconfig > +++ b/drivers/net/can/usb/Kconfig > @@ -38,6 +38,18 @@ config CAN_ETAS_ES58X > To compile this driver as a module, choose M here: the module > will be called etas_es58x. > > +config CAN_F81604 > + tristate "Fintek F81604 USB to 2CAN interface" > + help > + This driver supports the Fintek F81604 USB to 2CAN interface. > + The device can support CAN2.0A/B protocol and also support > + 2 output pins to control external terminator (optional). > + > + To compile this driver as a module, choose M here: the module will > + be called f81604. > + > + (see also https://www.fintek.com.tw). > + > config CAN_GS_USB > tristate "Geschwister Schneider UG and candleLight compatible interfaces" > help > diff --git a/drivers/net/can/usb/Makefile b/drivers/net/can/usb/Makefile > index 1ea16be5743b..8b11088e9a59 100644 > --- a/drivers/net/can/usb/Makefile > +++ b/drivers/net/can/usb/Makefile > @@ -7,6 +7,7 @@ obj-$(CONFIG_CAN_8DEV_USB) += usb_8dev.o > obj-$(CONFIG_CAN_EMS_USB) += ems_usb.o > obj-$(CONFIG_CAN_ESD_USB) += esd_usb.o > obj-$(CONFIG_CAN_ETAS_ES58X) += etas_es58x/ > +obj-$(CONFIG_CAN_F81604) += f81604.o > obj-$(CONFIG_CAN_GS_USB) += gs_usb.o > obj-$(CONFIG_CAN_KVASER_USB) += kvaser_usb/ > obj-$(CONFIG_CAN_MCBA_USB) += mcba_usb.o > diff --git a/drivers/net/can/usb/f81604.c b/drivers/net/can/usb/f81604.c > new file mode 100644 > index 000000000000..ce83a7993c4b > --- /dev/null > +++ b/drivers/net/can/usb/f81604.c > @@ -0,0 +1,1221 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* Fintek F81604 USB-to-2CAN controller driver. > + * > + * Copyright (C) 2023 Ji-Ze Hong (Peter Hong) <peter_hong@xxxxxxxxxxxxx> > + */ > +#include <linux/bitfield.h> > +#include <linux/netdevice.h> > +#include <linux/units.h> > +#include <linux/usb.h> > + > +#include <linux/can.h> > +#include <linux/can/dev.h> > +#include <linux/can/error.h> > +#include <linux/can/platform/sja1000.h> > + > +#include <asm-generic/unaligned.h> > + > +/* vendor and product id */ > +#define F81604_VENDOR_ID 0x2c42 > +#define F81604_PRODUCT_ID 0x1709 > +#define F81604_CAN_CLOCK (24 * MEGA / 2) Why not: #define F81604_CAN_CLOCK (12 * MEGA) ? > +#define F81604_MAX_DEV 2 > +#define F81604_SET_DEVICE_RETRY 10 > + > +#define F81604_USB_TIMEOUT 2000 > +#define F81604_SET_GET_REGISTER 0xA0 > +#define F81604_PORT_OFFSET 0x1000 > + > +#define F81604_BULK_SIZE 64 > +#define F81604_INT_SIZE 16 > +#define F81604_DATA_SIZE 14 > +#define F81604_MAX_RX_URBS 4 > + > +#define F81604_CMD_DATA 0x00 > + > +#define F81604_DLC_LEN_MASK 0x0f > +#define F81604_DLC_EFF_BIT BIT(7) > +#define F81604_DLC_RTR_BIT BIT(6) > + > +#define F81604_BRP_MASK GENMASK(5, 0) > +#define F81604_SJW_MASK GENMASK(7, 6) > + > +#define F81604_SEG1_MASK GENMASK(3, 0) > +#define F81604_SEG2_MASK GENMASK(6, 4) > + > +#define F81604_CLEAR_ALC 0 > +#define F81604_CLEAR_ECC 1 > +#define F81604_CLEAR_OVERRUN 2 > + > +/* device setting */ > +#define F81604_CTRL_MODE_REG 0x80 > +#define F81604_TX_ONESHOT (0x03 << 3) > +#define F81604_TX_NORMAL (0x01 << 3) > +#define F81604_RX_AUTO_RELEASE_BUF BIT(1) > +#define F81604_INT_WHEN_CHANGE BIT(0) > + > +#define F81604_TERMINATOR_REG 0x105 > +#define F81604_CAN0_TERM BIT(2) > +#define F81604_CAN1_TERM BIT(3) > + > +#define F81604_TERMINATION_DISABLED CAN_TERMINATION_DISABLED > +#define F81604_TERMINATION_ENABLED 120 > + > +/* SJA1000 registers - manual section 6.4 (Pelican Mode) */ > +#define F81604_SJA1000_MOD 0x00 > +#define F81604_SJA1000_CMR 0x01 > +#define F81604_SJA1000_IR 0x03 > +#define F81604_SJA1000_IER 0x04 > +#define F81604_SJA1000_ALC 0x0B > +#define F81604_SJA1000_ECC 0x0C > +#define F81604_SJA1000_RXERR 0x0E > +#define F81604_SJA1000_TXERR 0x0F > +#define F81604_SJA1000_ACCC0 0x10 > +#define F81604_SJA1000_ACCM0 0x14 > +#define F81604_MAX_FILTER_CNT 4 > + > +/* Common registers - manual section 6.5 */ > +#define F81604_SJA1000_BTR0 0x06 > +#define F81604_SJA1000_BTR1 0x07 > +#define F81604_SJA1000_BTR1_SAMPLE_TRIPLE BIT(7) > +#define F81604_SJA1000_OCR 0x08 > +#define F81604_SJA1000_CDR 0x1F > + > +/* mode register */ > +#define F81604_SJA1000_MOD_RM 0x01 > +#define F81604_SJA1000_MOD_LOM 0x02 > +#define F81604_SJA1000_MOD_STM 0x04 > + > +/* commands */ > +#define F81604_SJA1000_CMD_CDO 0x08 > + > +/* interrupt sources */ > +#define F81604_SJA1000_IRQ_BEI 0x80 > +#define F81604_SJA1000_IRQ_ALI 0x40 > +#define F81604_SJA1000_IRQ_EPI 0x20 > +#define F81604_SJA1000_IRQ_DOI 0x08 > +#define F81604_SJA1000_IRQ_EI 0x04 > +#define F81604_SJA1000_IRQ_TI 0x02 > +#define F81604_SJA1000_IRQ_RI 0x01 > +#define F81604_SJA1000_IRQ_ALL 0xFF > +#define F81604_SJA1000_IRQ_OFF 0x00 > + > +/* status register content */ > +#define F81604_SJA1000_SR_BS 0x80 > +#define F81604_SJA1000_SR_ES 0x40 > +#define F81604_SJA1000_SR_TCS 0x08 > + > +/* ECC register */ > +#define F81604_SJA1000_ECC_SEG 0x1F > +#define F81604_SJA1000_ECC_DIR 0x20 > +#define F81604_SJA1000_ECC_BIT 0x00 > +#define F81604_SJA1000_ECC_FORM 0x40 > +#define F81604_SJA1000_ECC_STUFF 0x80 > +#define F81604_SJA1000_ECC_MASK 0xc0 > + > +/* ALC register */ > +#define F81604_SJA1000_ALC_MASK 0x1f > + > +/* table of devices that work with this driver */ > +static const struct usb_device_id f81604_table[] = { > + { USB_DEVICE(F81604_VENDOR_ID, F81604_PRODUCT_ID) }, > + {} /* Terminating entry */ > +}; > + > +MODULE_DEVICE_TABLE(usb, f81604_table); > + > +static const struct ethtool_ops f81604_ethtool_ops = { > + .get_ts_info = ethtool_op_get_ts_info, > +}; > + > +static const u16 f81604_termination[] = { F81604_TERMINATION_DISABLED, > + F81604_TERMINATION_ENABLED }; > + > +struct f81604_priv { > + struct net_device *netdev[F81604_MAX_DEV]; > +}; > + > +struct f81604_port_priv { > + struct can_priv can; > + struct net_device *netdev; > + struct sk_buff *echo_skb; > + > + unsigned long clear_flags; > + struct work_struct clear_reg_work; > + > + struct usb_device *dev; > + struct usb_interface *intf; > + > + struct usb_anchor urbs_anchor; > +}; > + > +/* Interrupt endpoint data format: > + * Byte 0: Status register. > + * Byte 1: Interrupt register. > + * Byte 2: Interrupt enable register. > + * Byte 3: Arbitration lost capture(ALC) register. > + * Byte 4: Error code capture(ECC) register. > + * Byte 5: Error warning limit register. > + * Byte 6: RX error counter register. > + * Byte 7: TX error counter register. > + * Byte 8: Reserved. > + */ > +struct f81604_int_data { > + u8 sr; > + u8 isrc; > + u8 ier; > + u8 alc; > + u8 ecc; > + u8 ewlr; > + u8 rxerr; > + u8 txerr; > + u8 val; > +} __packed __aligned(4); > + > +struct f81604_sff { > + __be16 id; > + u8 data[CAN_MAX_DLEN]; > +} __packed __aligned(2); > + > +struct f81604_eff { > + __be32 id; > + u8 data[CAN_MAX_DLEN]; > +} __packed __aligned(2); > + > +struct f81604_can_frame { > + u8 cmd; > + > + /* According for F81604 DLC define: > + * bit 3~0: data length (0~8) > + * bit6: is RTR flag. > + * bit7: is EFF frame. > + */ > + u8 dlc; > + > + union { > + struct f81604_sff sff; > + struct f81604_eff eff; > + }; > +} __packed; __aligned(2)? > + > +static_assert(sizeof(struct f81604_can_frame) == F81604_DATA_SIZE); > + > +static const u8 bulk_in_addr[F81604_MAX_DEV] = { 2, 4 }; > +static const u8 bulk_out_addr[F81604_MAX_DEV] = { 1, 3 }; > +static const u8 int_in_addr[F81604_MAX_DEV] = { 1, 3 }; > + > +static int f81604_write(struct usb_device *dev, u16 reg, u8 data) > +{ > + int ret; > + > + ret = usb_control_msg_send(dev, 0, F81604_SET_GET_REGISTER, > + USB_TYPE_VENDOR | USB_DIR_OUT, 0, reg, > + &data, sizeof(data), F81604_USB_TIMEOUT, > + GFP_KERNEL); > + if (ret) > + dev_err(&dev->dev, "%s: reg: %x data: %x failed: %pe\n", > + __func__, reg, data, ERR_PTR(ret)); > + > + return ret; > +} > + > +static int f81604_read(struct usb_device *dev, u16 reg, u8 *data) > +{ > + int ret; > + > + ret = usb_control_msg_recv(dev, 0, F81604_SET_GET_REGISTER, > + USB_TYPE_VENDOR | USB_DIR_IN, 0, reg, data, > + sizeof(*data), F81604_USB_TIMEOUT, > + GFP_KERNEL); > + > + if (ret < 0) > + dev_err(&dev->dev, "%s: reg: %x failed: %pe\n", __func__, reg, > + ERR_PTR(ret)); > + > + return ret; > +} > + > +static int f81604_update_bits(struct usb_device *dev, u16 reg, u8 mask, > + u8 data) > +{ > + int ret; > + u8 tmp; > + > + ret = f81604_read(dev, reg, &tmp); > + if (ret) > + return ret; > + > + tmp &= ~mask; > + tmp |= (mask & data); > + > + return f81604_write(dev, reg, tmp); > +} > + > +static int f81604_sja1000_write(struct f81604_port_priv *priv, u16 reg, > + u8 data) > +{ > + int port = priv->netdev->dev_id; > + int real_reg; > + > + real_reg = reg + F81604_PORT_OFFSET * port + F81604_PORT_OFFSET; > + return f81604_write(priv->dev, real_reg, data); > +} > + > +static int f81604_sja1000_read(struct f81604_port_priv *priv, u16 reg, > + u8 *data) > +{ > + int port = priv->netdev->dev_id; > + int real_reg; > + > + real_reg = reg + F81604_PORT_OFFSET * port + F81604_PORT_OFFSET; > + return f81604_read(priv->dev, real_reg, data); > +} > + > +static int f81604_set_reset_mode(struct f81604_port_priv *priv) > +{ > + int ret, i; > + u8 tmp; > + > + /* disable interrupts */ > + ret = f81604_sja1000_write(priv, F81604_SJA1000_IER, > + F81604_SJA1000_IRQ_OFF); > + if (ret) > + return ret; > + > + for (i = 0; i < F81604_SET_DEVICE_RETRY; i++) { > + ret = f81604_sja1000_read(priv, F81604_SJA1000_MOD, &tmp); > + if (ret) > + return ret; > + > + /* check reset bit */ > + if (tmp & F81604_SJA1000_MOD_RM) { > + priv->can.state = CAN_STATE_STOPPED; > + return 0; > + } > + > + /* reset chip */ > + ret = f81604_sja1000_write(priv, F81604_SJA1000_MOD, > + F81604_SJA1000_MOD_RM); > + if (ret) > + return ret; > + } > + > + return -EPERM; > +} > + > +static int f81604_set_normal_mode(struct f81604_port_priv *priv) > +{ > + u8 tmp, ier = 0; > + u8 mod_reg = 0; > + int ret, i; > + > + for (i = 0; i < F81604_SET_DEVICE_RETRY; i++) { > + ret = f81604_sja1000_read(priv, F81604_SJA1000_MOD, &tmp); > + if (ret) > + return ret; > + > + /* check reset bit */ > + if ((tmp & F81604_SJA1000_MOD_RM) == 0) { > + priv->can.state = CAN_STATE_ERROR_ACTIVE; > + /* enable interrupts, RI handled by bulk-in */ > + ier = F81604_SJA1000_IRQ_ALL & ~F81604_SJA1000_IRQ_RI; > + if (!(priv->can.ctrlmode & > + CAN_CTRLMODE_BERR_REPORTING)) > + ier &= ~F81604_SJA1000_IRQ_BEI; > + > + return f81604_sja1000_write(priv, F81604_SJA1000_IER, > + ier); > + } > + > + /* set chip to normal mode */ > + if (priv->can.ctrlmode & CAN_CTRLMODE_LISTENONLY) > + mod_reg |= F81604_SJA1000_MOD_LOM; > + if (priv->can.ctrlmode & CAN_CTRLMODE_PRESUME_ACK) > + mod_reg |= F81604_SJA1000_MOD_STM; > + > + ret = f81604_sja1000_write(priv, F81604_SJA1000_MOD, mod_reg); > + if (ret) > + return ret; > + } > + > + return -EPERM; > +} > + > +static int f81604_chipset_init(struct f81604_port_priv *priv) > +{ > + int i, ret; > + > + /* set clock divider and output control register */ > + ret = f81604_sja1000_write(priv, F81604_SJA1000_CDR, > + CDR_CBP | CDR_PELICAN); > + if (ret) > + return ret; > + > + /* set acceptance filter (accept all) */ > + for (i = 0; i < F81604_MAX_FILTER_CNT; ++i) { > + ret = f81604_sja1000_write(priv, F81604_SJA1000_ACCC0 + i, 0); > + if (ret) > + return ret; > + } > + > + for (i = 0; i < F81604_MAX_FILTER_CNT; ++i) { > + ret = f81604_sja1000_write(priv, F81604_SJA1000_ACCM0 + i, > + 0xFF); > + if (ret) > + return ret; > + } > + > + return f81604_sja1000_write(priv, F81604_SJA1000_OCR, > + OCR_TX0_PUSHPULL | OCR_TX1_PUSHPULL | > + OCR_MODE_NORMAL); > +} > + > +static void f81604_process_rx_packet(struct urb *urb) > +{ > + struct net_device *netdev = urb->context; > + struct net_device_stats *stats; > + struct f81604_can_frame *frame; > + struct can_frame *cf; > + struct sk_buff *skb; > + unsigned int count; > + unsigned int i; :> + u8 *data; Do not use an opaque pointer. You can directly cast to an array of struct f81604_can_frame: struct f81604_can_frame *frames = urb->transfer_buffer; > + data = urb->transfer_buffer; > + stats = &netdev->stats; > + > + if (urb->actual_length % F81604_DATA_SIZE) > + netdev_warn(netdev, "URB length %u not multiple of %u\n", > + urb->actual_length, F81604_DATA_SIZE); > + else if (!urb->actual_length) > + netdev_warn(netdev, "URB length is 0\n"); > + > + count = urb->actual_length / F81604_DATA_SIZE; It would be better to have the URB sanitization inside f81604_read_bulk_callback(). > + for (i = 0; i < count; ++i) { The loop iteration can also be in f81604_read_bulk_callback(). > + frame = (struct f81604_can_frame *)&data[i * F81604_DATA_SIZE]; > + > + if (frame->cmd != F81604_CMD_DATA) > + continue; > + > + skb = alloc_can_skb(netdev, &cf); > + if (!skb) { > + stats->rx_dropped++; > + continue; > + } > + > + cf->len = can_cc_dlc2len(frame->dlc & F81604_DLC_LEN_MASK); > + > + if (frame->dlc & F81604_DLC_EFF_BIT) { > + cf->can_id = get_unaligned_be32(&frame->eff.id) >> 3; Use a #define instead of magic number. > + cf->can_id |= CAN_EFF_FLAG; > + > + if (cf->len) No need to check if len is not zero. memcpy(cf->data, frame->eff.data, 0) works fine. However, you need to check that this is not an RTR frame: if (!(frame->dlc & F81604_DLC_RTR_BIT)) > + memcpy(cf->data, frame->eff.data, cf->len); > + } else { > + cf->can_id = get_unaligned_be16(&frame->sff.id) >> 5; Use a #define instead of magic number. > + > + if (cf->len) No need to check if len is not zero. memcpy(cf->data, frame->eff.data, 0) works fine. However, you need to check that this is not an RTR frame: if (!(frame->dlc & F81604_DLC_RTR_BIT)) > + memcpy(cf->data, frame->sff.data, cf->len); > + } > + > + if (frame->dlc & F81604_DLC_RTR_BIT) > + cf->can_id |= CAN_RTR_FLAG; > + else > + stats->rx_bytes += cf->len; > + > + stats->rx_packets++; > + netif_rx(skb); > + } > +} > + > +static void f81604_read_bulk_callback(struct urb *urb) > +{ > + struct net_device *netdev = urb->context; + struct f81604_can_frame *frames = urb->transfer_buffer; + int i; > + int ret; > + > + if (!netif_device_present(netdev)) > + return; > + > + if (urb->status) > + netdev_info(netdev, "%s: URB aborted %pe\n", __func__, > + ERR_PTR(urb->status)); > + > + switch (urb->status) { > + case 0: /* success */ > + break; > + > + case -ENOENT: > + case -EPIPE: > + case -EPROTO: > + case -ESHUTDOWN: > + return; > + > + default: > + goto resubmit_urb; > + } Something like that (c.f. above): + if (urb->actual_length % F81604_DATA_SIZE) + netdev_warn(netdev, "URB length %u not multiple of %u\n", + urb->actual_length, F81604_DATA_SIZE); + else if (!urb->actual_length) + netdev_warn(netdev, "URB length is 0\n"); + + for (i = 0; i < urb->actual_length / sizeof(f81604_can_frame[0]; i++) + f81604_process_rx_packet(netdev, &f81604_can_frame[i]); > +resubmit_urb: > + ret = usb_submit_urb(urb, GFP_ATOMIC); > + if (ret == -ENODEV) > + netif_device_detach(netdev); > + else if (ret) > + netdev_err(netdev, > + "%s: failed to resubmit read bulk urb: %pe\n", > + __func__, ERR_PTR(ret)); > +} > + > +static void f81604_handle_tx(struct f81604_port_priv *priv, > + struct f81604_int_data *data) > +{ > + struct net_device *netdev = priv->netdev; > + struct net_device_stats *stats; > + > + stats = &netdev->stats; > + > + /* transmission buffer released */ > + if (priv->can.ctrlmode & CAN_CTRLMODE_ONE_SHOT && > + !(data->sr & F81604_SJA1000_SR_TCS)) { > + stats->tx_errors++; > + can_free_echo_skb(netdev, 0, NULL); > + } else { > + /* transmission complete */ > + stats->tx_bytes += can_get_echo_skb(netdev, 0, NULL); > + stats->tx_packets++; > + } > + > + netif_wake_queue(netdev); > +} > + > +static void f81604_handle_can_bus_errors(struct f81604_port_priv *priv, > + struct f81604_int_data *data) > +{ > + enum can_state can_state = priv->can.state; > + struct net_device *netdev = priv->netdev; > + enum can_state tx_state, rx_state; > + struct net_device_stats *stats; > + struct can_frame *cf; > + struct sk_buff *skb; > + > + stats = &netdev->stats; > + > + /* Note: ALC/ECC will not auto clear by read here, must be cleared by > + * read register (via clear_reg_work). > + */ > + > + skb = alloc_can_err_skb(netdev, &cf); > + if (skb) { > + cf->can_id |= CAN_ERR_CNT; > + cf->data[6] = data->txerr; > + cf->data[7] = data->rxerr; > + } > + > + if (data->isrc & F81604_SJA1000_IRQ_DOI) { > + /* data overrun interrupt */ > + netdev_dbg(netdev, "data overrun interrupt\n"); > + > + if (skb) { > + cf->can_id |= CAN_ERR_CRTL; > + cf->data[1] = CAN_ERR_CRTL_RX_OVERFLOW; > + } > + > + stats->rx_over_errors++; > + stats->rx_errors++; > + > + set_bit(F81604_CLEAR_OVERRUN, &priv->clear_flags); > + } > + > + if (data->isrc & F81604_SJA1000_IRQ_EI) { > + /* error warning interrupt */ > + netdev_dbg(netdev, "error warning interrupt\n"); > + > + if (data->sr & F81604_SJA1000_SR_BS) > + can_state = CAN_STATE_BUS_OFF; > + else if (data->sr & F81604_SJA1000_SR_ES) > + can_state = CAN_STATE_ERROR_WARNING; > + else > + can_state = CAN_STATE_ERROR_ACTIVE; > + } > + > + if (data->isrc & F81604_SJA1000_IRQ_BEI) { > + /* bus error interrupt */ > + netdev_dbg(netdev, "bus error interrupt\n"); > + > + priv->can.can_stats.bus_error++; > + stats->rx_errors++; > + > + if (skb) { > + cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR; > + > + /* set error type */ > + switch (data->ecc & F81604_SJA1000_ECC_MASK) { > + case F81604_SJA1000_ECC_BIT: > + cf->data[2] |= CAN_ERR_PROT_BIT; > + break; > + case F81604_SJA1000_ECC_FORM: > + cf->data[2] |= CAN_ERR_PROT_FORM; > + break; > + case F81604_SJA1000_ECC_STUFF: > + cf->data[2] |= CAN_ERR_PROT_STUFF; > + break; > + default: > + break; > + } > + > + /* set error location */ > + cf->data[3] = data->ecc & F81604_SJA1000_ECC_SEG; > + > + /* Error occurred during transmission? */ > + if ((data->ecc & F81604_SJA1000_ECC_DIR) == 0) > + cf->data[2] |= CAN_ERR_PROT_TX; > + } > + > + set_bit(F81604_CLEAR_ECC, &priv->clear_flags); > + } > + > + if (data->isrc & F81604_SJA1000_IRQ_EPI) { > + if (can_state == CAN_STATE_ERROR_PASSIVE) > + can_state = CAN_STATE_ERROR_WARNING; > + else > + can_state = CAN_STATE_ERROR_PASSIVE; > + > + /* error passive interrupt */ > + netdev_dbg(netdev, "error passive interrupt: %d\n", can_state); > + } > + > + if (data->isrc & F81604_SJA1000_IRQ_ALI) { > + /* arbitration lost interrupt */ > + netdev_dbg(netdev, "arbitration lost interrupt\n"); > + > + priv->can.can_stats.arbitration_lost++; > + > + if (skb) { > + cf->can_id |= CAN_ERR_LOSTARB; > + cf->data[0] = data->alc & F81604_SJA1000_ALC_MASK; > + } > + > + set_bit(F81604_CLEAR_ALC, &priv->clear_flags); > + } > + > + if (can_state != priv->can.state) { > + tx_state = data->txerr >= data->rxerr ? can_state : 0; > + rx_state = data->txerr <= data->rxerr ? can_state : 0; > + > + can_change_state(netdev, cf, tx_state, rx_state); > + > + if (can_state == CAN_STATE_BUS_OFF) > + can_bus_off(netdev); > + } > + > + if (priv->clear_flags) > + schedule_work(&priv->clear_reg_work); > + > + if (skb) > + netif_rx(skb); > +} > + > +static void f81604_read_int_callback(struct urb *urb) > +{ > + struct f81604_int_data *data = urb->transfer_buffer; > + struct net_device *netdev = urb->context; > + struct f81604_port_priv *priv; > + int ret; > + > + priv = netdev_priv(netdev); > + > + if (!netif_device_present(netdev)) > + return; > + > + if (urb->status) > + netdev_info(netdev, "%s: Int URB aborted: %pe\n", __func__, > + ERR_PTR(urb->status)); > + > + switch (urb->status) { > + case 0: /* success */ > + break; > + > + case -ENOENT: > + case -EPIPE: > + case -EPROTO: > + case -ESHUTDOWN: > + return; > + > + default: > + goto resubmit_urb; > + } > + > + /* handle Errors */ > + if (data->isrc & (F81604_SJA1000_IRQ_DOI | F81604_SJA1000_IRQ_EI | > + F81604_SJA1000_IRQ_BEI | F81604_SJA1000_IRQ_EPI | > + F81604_SJA1000_IRQ_ALI)) > + f81604_handle_can_bus_errors(priv, data); > + > + /* handle TX */ > + if (priv->can.state != CAN_STATE_BUS_OFF && > + (data->isrc & F81604_SJA1000_IRQ_TI)) > + f81604_handle_tx(priv, data); > + > +resubmit_urb: > + ret = usb_submit_urb(urb, GFP_ATOMIC); > + if (ret == -ENODEV) > + netif_device_detach(netdev); > + else if (ret) > + netdev_err(netdev, "%s: failed to resubmit int urb: %pe\n", > + __func__, ERR_PTR(ret)); > +} > + > +static void f81604_unregister_urbs(struct f81604_port_priv *priv) > +{ > + usb_kill_anchored_urbs(&priv->urbs_anchor); > +} > + > +static int f81604_register_urbs(struct f81604_port_priv *priv) > +{ > + struct net_device *netdev = priv->netdev; > + struct urb *rx_urb, *int_urb; > + int id = netdev->dev_id; > + u8 *rx_buf, *int_buf; No opaque buffer, please. > + int rx_urb_cnt; > + int ret; > + > + for (rx_urb_cnt = 0; rx_urb_cnt < F81604_MAX_RX_URBS; ++rx_urb_cnt) { > + rx_urb = usb_alloc_urb(0, GFP_KERNEL); > + if (!rx_urb) { > + ret = -ENOMEM; > + break; > + } > + > + rx_buf = kmalloc(F81604_BULK_SIZE, GFP_KERNEL); If I understand correctly, rx_buf contains some struct f81604_can_frame. What about: struct f81604_can_frame *frames; frames = kmalloc_array(F81604_RX_MAX_FRAMES_CNT, sizeof(*frame), GFP_KERNEL); ? With F81604_RX_MAX_FRAMES_CNT the maximum number of frames the device is capable of sending in one bulk. > + if (!rx_buf) { > + usb_free_urb(rx_urb); > + ret = -ENOMEM; > + break; > + } > + > + usb_fill_bulk_urb(rx_urb, priv->dev, > + usb_rcvbulkpipe(priv->dev, bulk_in_addr[id]), > + rx_buf, F81604_BULK_SIZE, > + f81604_read_bulk_callback, netdev); > + > + rx_urb->transfer_flags |= URB_FREE_BUFFER; > + usb_anchor_urb(rx_urb, &priv->urbs_anchor); > + > + ret = usb_submit_urb(rx_urb, GFP_KERNEL); > + if (ret) { > + usb_unanchor_urb(rx_urb); > + usb_free_urb(rx_urb); > + > + break; > + } > + > + /* Drop reference, USB core will take care of freeing it */ > + usb_free_urb(rx_urb); > + } > + > + if (rx_urb_cnt == 0) { > + netdev_warn(netdev, "%s: submit rx urb failed: %pe\n", > + __func__, ERR_PTR(ret)); > + > + goto error; > + } > + int_urb = usb_alloc_urb(0, GFP_KERNEL); > + if (!int_urb) { > + ret = -ENOMEM; > + goto error; > + } > + > + int_buf = kmalloc(F81604_BULK_SIZE, GFP_KERNEL); Why F81604_BULK_SIZE? The int_buf is a struct f81604_int_data, right? struct f81604_int_data *int_data; int_data = kmalloc(sizeof(*int_data), GFP_KERNEL); > + if (!int_buf) { > + usb_free_urb(int_urb); > + ret = -ENOMEM; > + goto error; > + } > + > + usb_fill_int_urb(int_urb, priv->dev, > + usb_rcvintpipe(priv->dev, int_in_addr[id]), int_buf, > + F81604_INT_SIZE, f81604_read_int_callback, netdev, 1); usb_fill_int_urb(int_urb, priv->dev, usb_rcvintpipe(priv->dev, int_in_addr[id]), int_data, sizeof(*int_data), f81604_read_int_callback, netdev, 1); > + > + int_urb->transfer_flags |= URB_FREE_BUFFER; > + usb_anchor_urb(int_urb, &priv->urbs_anchor); > + > + ret = usb_submit_urb(int_urb, GFP_KERNEL); > + if (ret) { > + usb_unanchor_urb(int_urb); > + usb_free_urb(int_urb); > + > + netdev_warn(netdev, "%s: submit int urb failed: %pe\n", > + __func__, ERR_PTR(ret)); > + goto error; > + } > + > + /* Drop reference, USB core will take care of freeing it */ > + usb_free_urb(int_urb); > + > + return 0; > + > +error: > + f81604_unregister_urbs(priv); > + return ret; > +} > + > +static int f81604_start(struct net_device *netdev) > +{ > + struct f81604_port_priv *priv = netdev_priv(netdev); > + int ret; > + u8 mode; > + u8 tmp; > + > + mode = F81604_RX_AUTO_RELEASE_BUF | F81604_INT_WHEN_CHANGE; > + > + /* Set TR/AT mode */ > + if (priv->can.ctrlmode & CAN_CTRLMODE_ONE_SHOT) > + mode |= F81604_TX_ONESHOT; > + else > + mode |= F81604_TX_NORMAL; > + > + ret = f81604_sja1000_write(priv, F81604_CTRL_MODE_REG, mode); > + if (ret) > + return ret; > + > + /* set reset mode */ > + ret = f81604_set_reset_mode(priv); > + if (ret) > + return ret; > + > + ret = f81604_chipset_init(priv); > + if (ret) > + return ret; > + > + /* Clear error counters and error code capture */ > + ret = f81604_sja1000_write(priv, F81604_SJA1000_TXERR, 0); > + if (ret) > + return ret; > + > + ret = f81604_sja1000_write(priv, F81604_SJA1000_RXERR, 0); > + if (ret) > + return ret; > + > + /* Read clear for ECC/ALC/IR register */ > + ret = f81604_sja1000_read(priv, F81604_SJA1000_ECC, &tmp); > + if (ret) > + return ret; > + > + ret = f81604_sja1000_read(priv, F81604_SJA1000_ALC, &tmp); > + if (ret) > + return ret; > + > + ret = f81604_sja1000_read(priv, F81604_SJA1000_IR, &tmp); > + if (ret) > + return ret; > + > + ret = f81604_register_urbs(priv); > + if (ret) > + return ret; > + > + ret = f81604_set_normal_mode(priv); > + if (ret) { > + f81604_unregister_urbs(priv); > + return ret; > + } > + > + return 0; > +} > + > +static int f81604_set_bittiming(struct net_device *dev) > +{ > + struct f81604_port_priv *priv = netdev_priv(dev); > + struct can_bittiming *bt = &priv->can.bittiming; > + u8 btr0, btr1; > + int ret; > + > + btr0 = FIELD_PREP(F81604_BRP_MASK, bt->brp - 1) | > + FIELD_PREP(F81604_SJW_MASK, bt->sjw - 1); > + > + btr1 = FIELD_PREP(F81604_SEG1_MASK, > + bt->prop_seg + bt->phase_seg1 - 1) | > + FIELD_PREP(F81604_SEG2_MASK, bt->phase_seg2 - 1); > + > + if (priv->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES) > + btr1 |= F81604_SJA1000_BTR1_SAMPLE_TRIPLE; > + > + ret = f81604_sja1000_write(priv, F81604_SJA1000_BTR0, btr0); > + if (ret) { > + netdev_warn(dev, "%s: Set BTR0 failed: %pe\n", __func__, > + ERR_PTR(ret)); > + return ret; > + } > + > + ret = f81604_sja1000_write(priv, F81604_SJA1000_BTR1, btr1); > + if (ret) { > + netdev_warn(dev, "%s: Set BTR1 failed: %pe\n", __func__, > + ERR_PTR(ret)); > + return ret; > + } > + > + return 0; > +} > + > +static int f81604_set_mode(struct net_device *netdev, enum can_mode mode) > +{ > + int ret; > + > + switch (mode) { > + case CAN_MODE_START: > + ret = f81604_start(netdev); > + if (!ret && netif_queue_stopped(netdev)) > + netif_wake_queue(netdev); > + break; > + > + default: > + ret = -EOPNOTSUPP; > + } > + > + return ret; > +} > + > +static void f81604_write_bulk_callback(struct urb *urb) > +{ > + struct net_device *netdev = urb->context; > + > + if (!netif_device_present(netdev)) > + return; > + > + if (urb->status) > + netdev_info(netdev, "%s: Tx URB error: %pe\n", __func__, > + ERR_PTR(urb->status)); > +} > + > +static void f81604_clear_reg_work(struct work_struct *work) > +{ > + struct f81604_port_priv *priv; > + struct net_device *netdev; > + u8 tmp; > + > + priv = container_of(work, struct f81604_port_priv, clear_reg_work); > + netdev = priv->netdev; > + > + /* dummy read for clear Arbitration lost capture(ALC) register. */ > + if (test_and_clear_bit(F81604_CLEAR_ALC, &priv->clear_flags)) > + f81604_sja1000_read(priv, F81604_SJA1000_ALC, &tmp); > + > + /* dummy read for clear Error code capture(ECC) register. */ > + if (test_and_clear_bit(F81604_CLEAR_ECC, &priv->clear_flags)) > + f81604_sja1000_read(priv, F81604_SJA1000_ECC, &tmp); > + > + /* dummy write for clear data overrun flag. */ > + if (test_and_clear_bit(F81604_CLEAR_OVERRUN, &priv->clear_flags)) > + f81604_sja1000_write(priv, F81604_SJA1000_CMR, > + F81604_SJA1000_CMD_CDO); > +} > + > +static netdev_tx_t f81604_start_xmit(struct sk_buff *skb, > + struct net_device *netdev) > +{ > + struct can_frame *cf = (struct can_frame *)skb->data; > + struct f81604_port_priv *priv = netdev_priv(netdev); > + struct net_device_stats *stats = &netdev->stats; > + struct f81604_can_frame *frame; > + u32 id = priv->netdev->dev_id; > + struct urb *write_urb; > + u8 *bulk_write_buffer; Do not use an opaque buffer. Instead, directly use struct f81604_can_frame. > + int ret; > + > + if (can_dev_dropped_skb(netdev, skb)) > + return NETDEV_TX_OK; > + > + netif_stop_queue(netdev); > + > + write_urb = usb_alloc_urb(0, GFP_ATOMIC); > + if (!write_urb) > + goto nomem_urb; > + > + bulk_write_buffer = kzalloc(F81604_DATA_SIZE, GFP_ATOMIC); frame = kzalloc(sizeof(*frame), GFP_ATOMIC); > + if (!bulk_write_buffer) > + goto nomem_buf; > + > + usb_fill_bulk_urb(write_urb, priv->dev, > + usb_sndbulkpipe(priv->dev, bulk_out_addr[id]), > + bulk_write_buffer, F81604_DATA_SIZE, > + f81604_write_bulk_callback, priv->netdev); usb_fill_bulk_urb(write_urb, priv->dev, usb_sndbulkpipe(priv->dev, bulk_out_addr[id]), frame, sizeof(*frame), f81604_write_bulk_callback, priv->netdev); > + > + write_urb->transfer_flags |= URB_FREE_BUFFER; > + > + frame = (struct f81604_can_frame *)bulk_write_buffer; > + frame->cmd = F81604_CMD_DATA; > + frame->dlc = cf->len; > + > + if (cf->can_id & CAN_RTR_FLAG) > + frame->dlc |= F81604_DLC_RTR_BIT; > + > + if (cf->can_id & CAN_EFF_FLAG) { > + id = (cf->can_id & CAN_EFF_MASK) << 3; Same as above: use a define instead of magic number. > + put_unaligned_be32(id, &frame->eff.id); > + > + frame->dlc |= F81604_DLC_EFF_BIT; > + > + if (!(cf->can_id & CAN_RTR_FLAG)) > + memcpy(&frame->eff.data, cf->data, cf->len); > + } else { > + id = (cf->can_id & CAN_SFF_MASK) << 5; Same as above: use a define instead of magic number. > + put_unaligned_be16(id, &frame->sff.id); > + > + if (!(cf->can_id & CAN_RTR_FLAG)) > + memcpy(&frame->sff.data, cf->data, cf->len); > + } > + > + can_put_echo_skb(skb, netdev, 0, 0); > + > + ret = usb_submit_urb(write_urb, GFP_ATOMIC); > + if (ret) { > + netdev_err(netdev, "%s: failed to resubmit tx bulk urb: %pe\n", > + __func__, ERR_PTR(ret)); > + > + can_free_echo_skb(netdev, 0, NULL); > + stats->tx_dropped++; > + > + if (ret == -ENODEV) > + netif_device_detach(netdev); > + else > + netif_wake_queue(netdev); > + } > + > + /* let usb core take care of this urb */ > + usb_free_urb(write_urb); > + > + return NETDEV_TX_OK; > + > +nomem_buf: > + usb_free_urb(write_urb); > + > +nomem_urb: > + dev_kfree_skb(skb); > + stats->tx_dropped++; > + netif_wake_queue(netdev); > + > + return NETDEV_TX_OK; > +} > + > +static int f81604_get_berr_counter(const struct net_device *netdev, > + struct can_berr_counter *bec) > +{ > + struct f81604_port_priv *priv = netdev_priv(netdev); > + u8 txerr, rxerr; > + int ret; > + > + ret = f81604_sja1000_read(priv, F81604_SJA1000_TXERR, &txerr); > + if (ret) > + return ret; > + > + ret = f81604_sja1000_read(priv, F81604_SJA1000_RXERR, &rxerr); > + if (ret) > + return ret; > + > + bec->txerr = txerr; > + bec->rxerr = rxerr; > + > + return 0; > +} > + > +/* Open USB device */ > +static int f81604_open(struct net_device *netdev) > +{ > + int ret; > + > + ret = open_candev(netdev); > + if (ret) > + return ret; > + > + ret = f81604_start(netdev); > + if (ret) > + goto start_failed; > + > + netif_start_queue(netdev); > + return 0; > + > +start_failed: > + if (ret == -ENODEV) > + netif_device_detach(netdev); > + > + close_candev(netdev); > + > + return ret; > +} > + > +/* Close USB device */ > +static int f81604_close(struct net_device *netdev) > +{ > + struct f81604_port_priv *priv = netdev_priv(netdev); > + > + f81604_set_reset_mode(priv); > + > + netif_stop_queue(netdev); > + cancel_work_sync(&priv->clear_reg_work); > + close_candev(netdev); > + > + f81604_unregister_urbs(priv); > + > + return 0; > +} > + > +static const struct net_device_ops f81604_netdev_ops = { > + .ndo_open = f81604_open, > + .ndo_stop = f81604_close, > + .ndo_start_xmit = f81604_start_xmit, > + .ndo_change_mtu = can_change_mtu, > +}; > + > +static const struct can_bittiming_const f81604_bittiming_const = { > + .name = KBUILD_MODNAME, > + .tseg1_min = 1, > + .tseg1_max = 16, > + .tseg2_min = 1, > + .tseg2_max = 8, > + .sjw_max = 4, > + .brp_min = 1, > + .brp_max = 64, > + .brp_inc = 1, > +}; > + > +/* Called by the usb core when driver is unloaded or device is removed */ > +static void f81604_disconnect(struct usb_interface *intf) > +{ > + struct f81604_priv *priv = usb_get_intfdata(intf); > + struct f81604_port_priv *port_priv; > + int i; > + > + for (i = 0; i < ARRAY_SIZE(priv->netdev); ++i) { > + if (!priv->netdev[i]) > + continue; > + > + port_priv = netdev_priv(priv->netdev[i]); > + > + unregister_netdev(priv->netdev[i]); > + free_candev(priv->netdev[i]); > + } > +} > + > +static int __f81604_set_termination(struct usb_device *dev, int idx, u16 term) > +{ > + u8 mask, data = 0; > + > + if (idx == 0) > + mask = F81604_CAN0_TERM; > + else > + mask = F81604_CAN1_TERM; > + > + if (term) > + data = mask; > + > + return f81604_update_bits(dev, F81604_TERMINATOR_REG, mask, data); > +} > + > +static int f81604_set_termination(struct net_device *netdev, u16 term) > +{ > + struct f81604_port_priv *port_priv = netdev_priv(netdev); > + > + ASSERT_RTNL(); > + > + return __f81604_set_termination(port_priv->dev, netdev->dev_id, term); > +} > + > +static int f81604_probe(struct usb_interface *intf, > + const struct usb_device_id *id) > +{ > + struct usb_device *dev = interface_to_usbdev(intf); > + struct f81604_port_priv *port_priv; > + struct net_device *netdev; > + struct f81604_priv *priv; > + int i, ret; > + > + priv = devm_kzalloc(&intf->dev, sizeof(*priv), GFP_KERNEL); > + if (!priv) > + return -ENOMEM; > + > + usb_set_intfdata(intf, priv); > + > + for (i = 0; i < ARRAY_SIZE(priv->netdev); ++i) { > + ret = __f81604_set_termination(dev, i, 0); > + if (ret) { > + dev_err(&intf->dev, > + "Set can%d termination failed: %pe\n", i, That would print: Set can0 termination failed or: Set can1 termination failed But can0 and can1 could be already use if there are other can devices connected to the host. You should use a less ambiguous notation. e.g. "Setting termination of channel #%d failed: %pe" > + ERR_PTR(ret)); > + return ret; > + } > + } > + > + for (i = 0; i < ARRAY_SIZE(priv->netdev); ++i) { > + netdev = alloc_candev(sizeof(*port_priv), 1); > + if (!netdev) { > + dev_err(&intf->dev, "Couldn't alloc candev: %d\n", i); > + ret = -ENOMEM; > + > + goto failure_cleanup; > + } > + > + port_priv = netdev_priv(netdev); > + netdev->dev_id = i; I think that dev_port is more appropriated than dev_id here. c.f.: https://www.kernel.org/doc/Documentation/ABI/testing/sysfs-class-net > + INIT_WORK(&port_priv->clear_reg_work, f81604_clear_reg_work); > + init_usb_anchor(&port_priv->urbs_anchor); > + > + port_priv->intf = intf; > + port_priv->dev = dev; > + port_priv->netdev = netdev; > + port_priv->can.clock.freq = F81604_CAN_CLOCK; > + > + port_priv->can.termination_const = f81604_termination; > + port_priv->can.termination_const_cnt = > + ARRAY_SIZE(f81604_termination); > + port_priv->can.bittiming_const = &f81604_bittiming_const; > + port_priv->can.do_set_bittiming = f81604_set_bittiming; > + port_priv->can.do_set_mode = f81604_set_mode; > + port_priv->can.do_set_termination = f81604_set_termination; > + port_priv->can.do_get_berr_counter = f81604_get_berr_counter; > + port_priv->can.ctrlmode_supported = > + CAN_CTRLMODE_LISTENONLY | CAN_CTRLMODE_3_SAMPLES | > + CAN_CTRLMODE_ONE_SHOT | CAN_CTRLMODE_BERR_REPORTING | > + CAN_CTRLMODE_PRESUME_ACK; > + > + netdev->ethtool_ops = &f81604_ethtool_ops; > + netdev->netdev_ops = &f81604_netdev_ops; > + netdev->flags |= IFF_ECHO; > + > + SET_NETDEV_DEV(netdev, &intf->dev); > + > + ret = register_candev(netdev); > + if (ret) { > + netdev_err(netdev, "register CAN device failed: %pe\n", > + ERR_PTR(ret)); > + free_candev(netdev); > + > + goto failure_cleanup; > + } > + > + priv->netdev[i] = netdev; > + > + dev_info(&intf->dev, "Channel #%d registered as %s\n", i, > + netdev->name); Do not print this message. Instead do: netdev->dev_port = i; With this, you can then confirm the mapping using: udevadm info --attribute-walk /sys/class/net/canX | grep dev_port > + } > + > + return 0; > + > +failure_cleanup: > + f81604_disconnect(intf); > + return ret; > +} > + > +static struct usb_driver f81604_driver = { > + .name = KBUILD_MODNAME, > + .probe = f81604_probe, > + .disconnect = f81604_disconnect, > + .id_table = f81604_table, > +}; > + > +module_usb_driver(f81604_driver); > + > +MODULE_AUTHOR("Ji-Ze Hong (Peter Hong) <peter_hong@xxxxxxxxxxxxx>"); > +MODULE_DESCRIPTION("Fintek F81604 USB to 2xCANBUS"); > +MODULE_LICENSE("GPL"); > -- > 2.17.1 >
