Re: [PATCH v5 1/2] can: tcan4x5x: reset device before register access

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Sean

On 12/11/19 7:39 AM, Sean Nyekjaer wrote:
It's a good idea to reset a ip-block/spi device before using it, this
patch will reset the device.

And a generic reset function if needed elsewhere.

Signed-off-by: Sean Nyekjaer <sean@xxxxxxxxxx>
Signed-off-by: Marc Kleine-Budde <mkl@xxxxxxxxxxxxxx>
---
Changes since v3:
  - added reset if the reset_gpio is not avaliable

Changes since v4:
  - added error handling for the SPI I/O

  drivers/net/can/m_can/tcan4x5x.c | 29 +++++++++++++++++++++++++++--
  1 file changed, 27 insertions(+), 2 deletions(-)

diff --git a/drivers/net/can/m_can/tcan4x5x.c b/drivers/net/can/m_can/tcan4x5x.c
index b6b2feca9e8f..032d110e0870 100644
--- a/drivers/net/can/m_can/tcan4x5x.c
+++ b/drivers/net/can/m_can/tcan4x5x.c
@@ -166,6 +166,27 @@ static void tcan4x5x_check_wake(struct tcan4x5x_priv *priv)
  	}
  }
+static int tcan4x5x_reset(struct tcan4x5x_priv *priv)
+{
+	int ret = 0;
+
+	if (priv->reset_gpio) {
+		gpiod_set_value(priv->reset_gpio, 1);
+
+		/* tpulse_width minimum 30us */
+		usleep_range(30, 100);
+		gpiod_set_value(priv->reset_gpio, 0);
+	} else {
+		ret = regmap_write(priv->regmap, TCAN4X5X_CONFIG, TCAN4X5X_SW_RESET);
+		if (ret)
+			return ret;
+	}
+
+	usleep_range(700, 1000);
+
+	return ret;
+}
+
  static int regmap_spi_gather_write(void *context, const void *reg,
  				   size_t reg_len, const void *val,
  				   size_t val_len)
@@ -351,6 +372,7 @@ static int tcan4x5x_disable_wake(struct m_can_classdev *cdev)
  static int tcan4x5x_parse_config(struct m_can_classdev *cdev)
  {
  	struct tcan4x5x_priv *tcan4x5x = cdev->device_data;
+	int ret;
tcan4x5x->device_wake_gpio = devm_gpiod_get(cdev->dev, "device-wake",
  						    GPIOD_OUT_HIGH);
@@ -363,10 +385,13 @@ static int tcan4x5x_parse_config(struct m_can_classdev *cdev)
tcan4x5x->reset_gpio = devm_gpiod_get_optional(cdev->dev, "reset",
  						       GPIOD_OUT_LOW);
-	if (IS_ERR(tcan4x5x->reset_gpio))
+	if (IS_ERR(tcan4x5x->reset_gpio)) {
  		tcan4x5x->reset_gpio = NULL;
+	}

Why did you add brackets?

This is not needed for single statement if's

Dan



[Index of Archives]     [Automotive Discussions]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux]     [Linux OMAP]     [Linux MIPS]     [eCos]     [Asterisk Internet PBX]     [Linux API]     [CAN Bus]

  Powered by Linux