Re: [PATCH v2 1/2] dt-bindings: net: broadcom-bluetooth: Add property for autobaud mode

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Krzysztof,

Thanks for responding.

On 5/22/2022 10:14 AM, Krzysztof Kozlowski wrote:
Some devices (e.g. CYW5557x) require autobaud mode to enable FW loading.
Which devices support this? You probably need allOf:if:then.

Most devices _support_ autobaud mode but I don't have a definitive list. The CYW5557x is the first device family to _require_ autobaud mode for FW loading as far as I know.

Autobaud mode can also be required on some boards where the controller
device is using a non-standard baud rate when first powered on.

This patch adds a property, "brcm,uses-autobaud-mode", to enable autobaud
mode selection.
Don't use "This patch":
https://elixir.bootlin.com/linux/v5.17.1/source/Documentation/process/submitting-patches.rst#L95

Sorry, will change in next rev.

Signed-off-by: Hakan Jansson <hakan.jansson@xxxxxxxxxxxx>
---
V1 -> V2: Modify property description

  .../devicetree/bindings/net/broadcom-bluetooth.yaml      | 9 +++++++++
  1 file changed, 9 insertions(+)

diff --git a/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml b/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml
index 5aac094fd217..a29f059c21cc 100644
--- a/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml
+++ b/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml
@@ -92,6 +92,15 @@ properties:
         pcm-sync-mode: slave, master
         pcm-clock-mode: slave, master

+  brcm,uses-autobaud-mode:
Based on description, I understand the host triggers using autobaud.

Correct, the host triggers using autobaud.

However here you word it as "uses", so it is independent of host, it
looks like property of a device.

I've been thinking of it as a a property of a specific board HW, inherited either from a property of the device being used or from a property of the HW design (e.g. a PCB using an alternate crystal frequency yielding a non-standard baud rate).

  The commit msg describes it even
different - "require autobaud".

Yes, the commit message describes two separate reasons why autobaud mode would be required:

1. Requirement coming from Device: "Some devices (e.g. CYW5557x) require autobaud mode to enable FW loading."

2. Requirement coming from HW design: "Autobaud mode can also be required on some boards where the controller device is using a non-standard baud rate when first powered on."

This leads to second issue - it looks like there is some hardware
property (requiring to use autobaud) which should be described by
bindings. But instead you describe desired operational feature.

Sorry about that. I've really been struggling with what should go into the description. Any suggestions or hints would be much appreciated.

How about, changing the property name to "brcm,requires-autobaud-mode" and the description to: "Set this property if autobaud mode is required. Autobaud mode is required if the device's baud rate in normal mode is not supported by the host or if the device requires autobaud mode startup before loading FW."

Would that be an appropriate name and description?

+    type: boolean
+    description: >
No need for '>'.

Ok, will remove in next rev.

+      Setting this property will make the host (driver) assert the controller
+      chip's BT_UART_CTS_N prior to asserting BT_REG_ON. This will make the
+      controller start up in autobaud mode. The controller will then detect the
+      baud rate of the first incoming (HCI Reset) command from the host and
+      subsequently use that baud rate.
+
    interrupts:
      items:
        - description: Handle to the line HOST_WAKE used to wake


Thanks,
Håkan



[Index of Archives]     [Bluez Devel]     [Linux Wireless Networking]     [Linux Wireless Personal Area Networking]     [Linux ATH6KL]     [Linux USB Devel]     [Linux Media Drivers]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Big List of Linux Books]

  Powered by Linux