Hi Tedd,
> This patch fixes the broken LED quirk for Intel legacy ROM devices.
> To fix the LED issue that doesn't turn off immediately, the host sends
> the SW RFKILL command while shutting down the interface and it puts the
> devices in an asserted state.
>
> Once the device is in SW RFKILL state, it can only accept HCI_Reset to
> exit from the SW RFKILL state. This patch checks the quirk and sends the
> HCI_Reset before sending the HCI_Intel_Read_Version command.
>
> The affected legacy ROM devices are
> - 8087:0a2a
> - 8087:0aa7
>
> fixes: ffcba827c0a1d ("Bluetooth: btintel: Fix the LED is not turning off immediately")
>
> Signed-off-by: Tedd Ho-Jeong An <tedd.an@xxxxxxxxx>
> ---
> drivers/bluetooth/btintel.c | 13 ++++++-------
> drivers/bluetooth/btusb.c | 10 ++++++++--
> 2 files changed, 14 insertions(+), 9 deletions(-)
>
> diff --git a/drivers/bluetooth/btintel.c b/drivers/bluetooth/btintel.c
> index e1f96df847b8..75f8d7aceb35 100644
> --- a/drivers/bluetooth/btintel.c
> +++ b/drivers/bluetooth/btintel.c
> @@ -2355,8 +2355,13 @@ static int btintel_setup_combined(struct hci_dev *hdev)
> * As a workaround, send HCI Reset command first which will reset the
> * number of completed commands and allow normal command processing
> * from now on.
> + *
> + * For INTEL_BROKEN_LED, these devices have an issue with LED which
> + * doesn't go off immediately during shutdown. Set the flag here to send
> + * the LED OFF command during shutdown.
> */
> - if (btintel_test_flag(hdev, INTEL_BROKEN_INITIAL_NCMD)) {
> + if (btintel_test_flag(hdev, INTEL_BROKEN_INITIAL_NCMD) ||
> + btintel_test_flag(hdev, INTEL_BROKEN_LED)) {
make sure to indent this as this:
if (btintel_test..(..) ||
btintel_test..(..)) {
And rename this into INTEL_BROKEN_SHUTDOWN_LED
> skb = __hci_cmd_sync(hdev, HCI_OP_RESET, 0, NULL,
> HCI_INIT_TIMEOUT);
> if (IS_ERR(skb)) {
> @@ -2428,12 +2433,6 @@ static int btintel_setup_combined(struct hci_dev *hdev)
> set_bit(HCI_QUIRK_WIDEBAND_SPEECH_SUPPORTED,
> &hdev->quirks);
>
> - /* These devices have an issue with LED which doesn't
> - * go off immediately during shutdown. Set the flag
> - * here to send the LED OFF command during shutdown.
> - */
> - btintel_set_flag(hdev, INTEL_BROKEN_LED);
> -
> err = btintel_legacy_rom_setup(hdev, &ver);
> break;
> case 0x0b: /* SfP */
> diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
> index d1bd9ee0a6ab..c6a070d5284f 100644
> --- a/drivers/bluetooth/btusb.c
> +++ b/drivers/bluetooth/btusb.c
> @@ -60,6 +60,7 @@ static struct usb_driver btusb_driver;
> #define BTUSB_WIDEBAND_SPEECH 0x400000
> #define BTUSB_VALID_LE_STATES 0x800000
> #define BTUSB_QCA_WCN6855 0x1000000
> +#define BTUSB_INTEL_BROKEN_LED 0x2000000
Use BTUSB_INTEL_BROKEN_SHUTDOWN_LED here.
> #define BTUSB_INTEL_BROKEN_INITIAL_NCMD 0x4000000
>
> static const struct usb_device_id btusb_table[] = {
> @@ -382,9 +383,11 @@ static const struct usb_device_id blacklist_table[] = {
> { USB_DEVICE(0x8087, 0x07da), .driver_info = BTUSB_CSR },
> { USB_DEVICE(0x8087, 0x07dc), .driver_info = BTUSB_INTEL_COMBINED |
> BTUSB_INTEL_BROKEN_INITIAL_NCMD },
This one needs both. I know it is just going to work, but for simplicity set it both so that WP2 uses this quirk in shutdown as well. So when you remove the set_flag from setup, you fail to run ->shutdown on WP2.
I know the BROKEN_INITIAL_NCMD is now pointless, but lets keep it for documentation sake.
> - { USB_DEVICE(0x8087, 0x0a2a), .driver_info = BTUSB_INTEL_COMBINED },
> + { USB_DEVICE(0x8087, 0x0a2a), .driver_info = BTUSB_INTEL_COMBINED |
> + BTUSB_INTEL_BROKEN_LED },
> { USB_DEVICE(0x8087, 0x0a2b), .driver_info = BTUSB_INTEL_COMBINED },
> - { USB_DEVICE(0x8087, 0x0aa7), .driver_info = BTUSB_INTEL_COMBINED },
> + { USB_DEVICE(0x8087, 0x0aa7), .driver_info = BTUSB_INTEL_COMBINED |
> + BTUSB_INTEL_BROKEN_LED },
> { USB_DEVICE(0x8087, 0x0aaa), .driver_info = BTUSB_INTEL_COMBINED },
>
> /* Other Intel Bluetooth devices */
> @@ -3724,6 +3727,9 @@ static int btusb_probe(struct usb_interface *intf,
>
> if (id->driver_info & BTUSB_INTEL_BROKEN_INITIAL_NCMD)
> btintel_set_flag(hdev, INTEL_BROKEN_INITIAL_NCMD);
> +
> + if (id->driver_info & BTUSB_INTEL_BROKEN_LED)
> + btintel_set_flag(hdev, INTEL_BROKEN_LED);
> }
Regards
Marcel
