Hi, this is your Linux kernel regression tracker speaking. To make this easy and quick to read for everyone I for once rely on top-posting: Bluetooth maintainers, what's the status here? The proposed patch is fixing a regression. It's not a recent one (it afaics was introduced in v5.11-rc1). Nevertheless it would be good to get this finally resolved. But this thread seems inactive for more than a week now. Or was progress made, but is only visible somewhere else? Ciao, Thorsten (carrying his Linux kernel regression tracker hat) P.S.: As a Linux kernel regression tracker I'm getting a lot of reports on my table. I can only look briefly into most of them. Therefore I unfortunately will get things wrong or miss something important. I hope that's not the case here; if you think it is, don't hesitate to tell me about it in a public reply. That's in everyone's interest, as what I wrote above might be misleading to everyone reading this, which is something I'd like to avoid. BTW, I have no personal interest in this issue, which is tracked using regzbot, my Linux kernel regression tracking bot (https://linux-regtracking.leemhuis.info/regzbot/). I'm only posting this mail to hopefully get things rolling again and hence don't need to be CC on all further activities wrt to this regression. Also feel free to ignore the following lines, they are meant for regzbot: #regzbot poke On 07.11.21 09:35, Greg KH wrote: > On Sat, Nov 06, 2021 at 05:27:27PM +0000, Aditya Garg wrote: >>> On 06-Nov-2021, at 5:19 PM, Greg KH <gregkh@xxxxxxxxxxxxxxxxxxx> wrote: >>> On Sat, Nov 06, 2021 at 09:41:28AM +0000, Aditya Garg wrote: >>>>> On 06-Nov-2021, at 3:17 AM, Luiz Augusto von Dentz <luiz.dentz@xxxxxxxxx> wrote: >>>>> On Fri, Oct 1, 2021 at 1:56 AM Orlando Chamberlain >>>>> <redecorating@xxxxxxxxxxxxxx> wrote: >>>>>> >>>>>> The LE Read Transmit Power command is Advertised on some Broadcom >>>>>> controlers, but not supported. Using this command breaks Bluetooth >>>>>> on the MacBookPro16,1 and iMac20,1. Added a quirk disabling LE Read >>>>>> Transmit Power for these devices, based off their common chip id 150. >>>>>> >>>>>> Link: https://lore.kernel.org/r/4970a940-211b-25d6-edab-21a815313954@xxxxxxxxxxxxxx >>>>>> Signed-off-by: Orlando Chamberlain <redecorating@xxxxxxxxxxxxxx> >>>>>> --- >>>>>> v1->v2: Clarified quirk description >>>>>> >>>>>> drivers/bluetooth/btbcm.c | 4 ++++ >>>>>> include/net/bluetooth/hci.h | 11 +++++++++++ >>>>>> net/bluetooth/hci_core.c | 3 ++- >>>>>> 3 files changed, 17 insertions(+), 1 deletion(-) >>>>>> >>>>>> diff --git a/drivers/bluetooth/btbcm.c b/drivers/bluetooth/btbcm.c >>>>>> index e4182acee488..4ecc50d93107 100644 >>>>>> --- a/drivers/bluetooth/btbcm.c >>>>>> +++ b/drivers/bluetooth/btbcm.c >>>>>> @@ -353,6 +353,10 @@ static int btbcm_read_info(struct hci_dev *hdev) >>>>>> return PTR_ERR(skb); >>>>>> >>>>>> bt_dev_info(hdev, "BCM: chip id %u", skb->data[1]); >>>>>> + >>>>>> + if (skb->data[1] == 150) >>>>>> + set_bit(HCI_QUIRK_BROKEN_READ_TRANSMIT_POWER, &hdev->quirks); >>>>>> + >>>>>> kfree_skb(skb); >>>>>> >>>>>> /* Read Controller Features */ >>>>>> diff --git a/include/net/bluetooth/hci.h b/include/net/bluetooth/hci.h >>>>>> index b80415011dcd..6da9bd6b7259 100644 >>>>>> --- a/include/net/bluetooth/hci.h >>>>>> +++ b/include/net/bluetooth/hci.h >>>>>> @@ -246,6 +246,17 @@ enum { >>>>>> * HCI after resume. >>>>>> */ >>>>>> HCI_QUIRK_NO_SUSPEND_NOTIFIER, >>>>>> + >>>>>> + /* When this quirk is set, LE Read Transmit Power is disabled. >>>>>> + * This is mainly due to the fact that the HCI LE Read Transmit >>>>>> + * Power command is advertised, but not supported; these >>>>>> + * controllers often reply with unknown command and need a hard >>>>>> + * reset. >>>>>> + * >>>>>> + * This quirk can be set before hci_register_dev is called or >>>>>> + * during the hdev->setup vendor callback. >>>>>> + */ >>>>>> + HCI_QUIRK_BROKEN_READ_TRANSMIT_POWER, >>>>>> }; >>>>>> >>>>>> /* HCI device flags */ >>>>>> diff --git a/net/bluetooth/hci_core.c b/net/bluetooth/hci_core.c >>>>>> index 8a47a3017d61..9a23fe7c8d67 100644 >>>>>> --- a/net/bluetooth/hci_core.c >>>>>> +++ b/net/bluetooth/hci_core.c >>>>>> @@ -742,7 +742,8 @@ static int hci_init3_req(struct hci_request *req, unsigned long opt) >>>>>> hci_req_add(req, HCI_OP_LE_READ_ADV_TX_POWER, 0, NULL); >>>>>> } >>>>>> >>>>>> - if (hdev->commands[38] & 0x80) { >>>>>> + if (hdev->commands[38] & 0x80 && >>>>>> + !test_bit(HCI_QUIRK_BROKEN_READ_TRANSMIT_POWER, &hdev->quirks)) { >>>>>> /* Read LE Min/Max Tx Power*/ >>>>>> hci_req_add(req, HCI_OP_LE_READ_TRANSMIT_POWER, >>>>>> 0, NULL); >>>>>> -- >>>>>> 2.33.0 >>>>> >>>>> Nowadays it is possible to treat errors such like this on a per >>>>> command basis (assuming it is not essential for the init sequence): >>>>> >>>>> diff --git a/include/net/bluetooth/hci.h b/include/net/bluetooth/hci.h >>>>> index 979da5179ff4..f244f42cc609 100644 >>>>> --- a/include/net/bluetooth/hci.h >>>>> +++ b/include/net/bluetooth/hci.h >>>>> @@ -551,6 +551,7 @@ enum { >>>>> #define HCI_LK_AUTH_COMBINATION_P256 0x08 >>>>> >>>>> /* ---- HCI Error Codes ---- */ >>>>> +#define HCI_ERROR_UNKNOWN_CMD 0x01 >>>>> #define HCI_ERROR_UNKNOWN_CONN_ID 0x02 >>>>> #define HCI_ERROR_AUTH_FAILURE 0x05 >>>>> #define HCI_ERROR_PIN_OR_KEY_MISSING 0x06 >>>>> diff --git a/net/bluetooth/hci_sync.c b/net/bluetooth/hci_sync.c >>>> This diff cannot be applied to stable 5.15. Could you provide a patch capable of being applied to stable. >>> >>> That is not needed until a patch is in Linus's tree. Why do you need it >>> earlier? >>> >> Well not an emergency, but the issue of Bluetooth not working on some Apple Macs has been there for a long time. BTW, will this patch be there in Linus’s tree in the coming days? > > That is up to the bluetooth maintainers, they have to accept it first. > > thanks, > > greg k-h > >
