From: Max Chou <max.chou@xxxxxxxxxxx>
For the commit of 9e45524a011107a73bc2cdde8370c61e82e93a4d, wakeup is
always disabled for Realtek devices. However, there's the capability
for Realtek devices to apply USB wake-up.
In this commit, remove WAKEUP_DISABLE feature for Realtek devices.
If users would switch wake-up, they should access
"/sys/bus/usb/.../power/wakeup"
In this commit, it also adds the feature as WAKEUP_AUTOSUSPEND
for Realtek devices because it should set do_remote_wakeup on autosuspend.
Signed-off-by: Max Chou <max.chou@xxxxxxxxxxx>
Tested-by: Hilda Wu <hildawu@xxxxxxxxxxx>
Reviewed-by: Archie Pusaka <apusaka@xxxxxxxxxxxx>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@xxxxxxxxxxxx>
---
drivers/bluetooth/btusb.c | 25 +++++++++----------------
1 file changed, 9 insertions(+), 16 deletions(-)
diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index 488f110e17e2..73a835bf37f7 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -527,7 +527,7 @@ static const struct dmi_system_id btusb_needs_reset_resume_table[] = {
#define BTUSB_OOB_WAKE_ENABLED 11
#define BTUSB_HW_RESET_ACTIVE 12
#define BTUSB_TX_WAIT_VND_EVT 13
-#define BTUSB_WAKEUP_DISABLE 14
+#define BTUSB_WAKEUP_AUTOSUSPEND 14
struct btusb_data {
struct hci_dev *hdev;
@@ -1349,13 +1349,6 @@ static int btusb_open(struct hci_dev *hdev)
data->intf->needs_remote_wakeup = 1;
- /* Disable device remote wakeup when host is suspended
- * For Realtek chips, global suspend without
- * SET_FEATURE (DEVICE_REMOTE_WAKEUP) can save more power in device.
- */
- if (test_bit(BTUSB_WAKEUP_DISABLE, &data->flags))
- device_wakeup_disable(&data->udev->dev);
-
if (test_and_set_bit(BTUSB_INTR_RUNNING, &data->flags))
goto done;
@@ -1422,7 +1415,7 @@ static int btusb_close(struct hci_dev *hdev)
data->intf->needs_remote_wakeup = 0;
/* Enable remote wake up for auto-suspend */
- if (test_bit(BTUSB_WAKEUP_DISABLE, &data->flags))
+ if (test_bit(BTUSB_WAKEUP_AUTOSUSPEND, &data->flags))
data->intf->needs_remote_wakeup = 1;
usb_autopm_put_interface(data->intf);
@@ -3877,11 +3870,8 @@ static int btusb_probe(struct usb_interface *intf,
hdev->shutdown = btrtl_shutdown_realtek;
hdev->cmd_timeout = btusb_rtl_cmd_timeout;
- /* Realtek devices lose their updated firmware over global
- * suspend that means host doesn't send SET_FEATURE
- * (DEVICE_REMOTE_WAKEUP)
- */
- set_bit(BTUSB_WAKEUP_DISABLE, &data->flags);
+ /* Realtek devices need to set remote wakeup on auto-suspend */
+ set_bit(BTUSB_WAKEUP_AUTOSUSPEND, &data->flags);
}
if (!reset)
@@ -4056,12 +4046,15 @@ static int btusb_suspend(struct usb_interface *intf, pm_message_t message)
* Actually, it depends on whether the usb host sends
* set feature (enable wakeup) or not.
*/
- if (test_bit(BTUSB_WAKEUP_DISABLE, &data->flags)) {
+ if (test_bit(BTUSB_WAKEUP_AUTOSUSPEND, &data->flags)) {
if (PMSG_IS_AUTO(message) &&
device_can_wakeup(&data->udev->dev))
data->udev->do_remote_wakeup = 1;
- else if (!PMSG_IS_AUTO(message))
+ else if (!PMSG_IS_AUTO(message) &&
+ !device_may_wakeup(&data->udev->dev)) {
+ data->udev->do_remote_wakeup = 0;
data->udev->reset_resume = 1;
+ }
}
return 0;
--
2.17.1
