Hi Marcel, I don't think this solves the original problem we were talking about: the driver should replace the runtime firmware on reload if it doesn't match what's on disk. Some background for the mailing list: - On a ChromeOS laptop, we discovered that the Bluetooth controller wasn't being fully powered down in some reboots. As a result, a new firmware wasn't being applied after an update. - The kernel driver was checking if the bluetooth controller had loaded some firmware already. If it was in bootloader mode, it would download new firmware. If it was not, it would skip downloading new firmware. The useful part of this mgmt command is to force the driver to reset to bootloader (Action = 0 in Set Runtime Firmware). However, without being able to compare the firmware version loaded on the controller, there's no clear signal for when this should be called. Loading the firmware through mgmt may be useful for debugging but you could also just replace the firmware on disk and "reset to bootloader" to achieve the same effect. I would actually expect unloading and reloading the module should do that. Also, moving the firmware loading from the driver to the userspace seems odd to me. Since the comparison is between the controller firmware and disk firmware, there's not much extra that the userspace knows that the kernel does not. ---- Coming back to the original problem of when to reload runtime firmware, here are the conditions under which we do and don't want a reload. Do want a reload: - Reboot - Module is unloaded and reloaded Don't want a reload: - Transport disconnection (i.e. usb disconnect; some laptops will power down USB during suspend to save additional power but BT will stay powered up) - Power toggle (bluetooth power off -> power on) - HCI reset Letting the kernel driver maintain some sort of table of previously configured devices might be a better option. We can put that table in the module's static memory space so that it doesn't get cleared on device disconnects. These should be useful for internally connected Bluetooth (which may not always power cycle between resets) and for which you may want to force reloads around reboot or module reload. Externally connected Bluetooth will power cycle once disconnected anyway so this is moot for them. Thanks, Abhishek On Tue, Dec 22, 2020 at 4:47 AM Marcel Holtmann <marcel@xxxxxxxxxxxx> wrote: > > --- > doc/mgmt-api.txt | 86 ++++++++++++++++++++++++++++++++++++++++++++++++ > 1 file changed, 86 insertions(+) > > diff --git a/doc/mgmt-api.txt b/doc/mgmt-api.txt > index 1736ef009e75..47686ae32629 100644 > --- a/doc/mgmt-api.txt > +++ b/doc/mgmt-api.txt > @@ -2187,6 +2187,7 @@ Read Controller Configuration Information Command > > 0 External configuration > 1 Bluetooth public address configuration > + 2 Runtime firmware configuration > > It is valid to call this command on controllers that do not > require any configuration. It is possible that a fully configured > @@ -3132,6 +3133,10 @@ Read Controller Capabilities Command > 0x02 Max Encryption Key Size (BR/EDR) > 0x03 Max Encryption Key Size (LE) > 0x04 Supported Tx Power (LE) > + 0x05 Complete firmware name > + 0x06 Shortened firmware name > + 0x07 Firmware info string > + 0x08 Hardware info string > > Flags (data type 0x01) > > @@ -3155,6 +3160,23 @@ Read Controller Capabilities Command > field is not available, it indicates that the LE Read > Transmit Power HCI command was not available. > > + Firmware name (date types 0x05 and 0x06) > + > + Only one of these will be present if the device is loading > + some sort of runtime firmware. Only in the firwmare name > + happens to exceed the 255 charaters, the shortened type > + shall be used. > + > + This value represents the driver chosen default firmware > + for a controller. In case it is changed via Set Runtime > + Firmware command that change will not be reflected here. > + > + Firmware and hardware info (data types 0x07 and 0x08) > + > + When provided by the hardware and the driver, these fields > + will contain string of the firmware or the hardware for > + debug or indentification purposes. > + > This command generates a Command Complete event on success or > a Command Status event on failure. > > @@ -3852,6 +3874,70 @@ Add Advertisement Patterns Monitor With RSSI Threshold Command > Invalid Parameters > > > +Set Runtime Firmware Command > +============================ > + > + Command Code: 0x0057 > + Controller Index: <controller id> > + Command Parameters: Action (1 Octet) > + Firmware_Length (2 Octets) > + Firmware (0-65535 Octets) > + Return Parameters: Missing_Options (4 Octets) > + > + This command allows configuration of runtime firmware or patch > + download setting. Since a vendor specific procedure is required, > + this command might not be supported by all controllers. > + > + Possible values for the Action parameter: > + 0 Reset to default driver firmware > + 1 Reset to current or configure new firmware > + > + When resetting to the default firmware, Firmware_Length shall be > + set to 0. The system will go back to the original firmware selected > + by the driver. When resetting to current firmware, Firmware_Length > + shall also be set to 0. If there has been never specified a new > + firmware, then a reset to default or current is not different. > + > + Loading a new firmware can be triggered with the Action 1 and a > + Firmware specified. The Firmware is a string that would also be > + used in request_firmware() and has to be NUL terminated. The > + Firmware_Length field shall include the string length plus the > + additional NUL byte. > + > + In the case a driver has no default driver firmware, then an > + Action 0 will fully reset the device into an unconfigured state. > + > + When the support for runtime firwmare configuration is indicated > + in the supported options mask, then this command can be used to > + set the runtime firmware. > + > + It is only possible to configure the runtime firmware when the > + controller is powered off. > + > + For an unconfigured controller and when Missing_Options returns > + an empty mask, this means that a Index Added event for the now > + fully configured controller can be expected. > + > + For a fully configured controller, the current controller index > + will become invalid and an Unconfigured Index Removed event will > + be sent. Once the firmware has been successfully loaded an Index > + Added event will be sent. There is no guarantee that the controller > + index stays the same. > + > + All previous configured parameters and settings are lost when > + this command succeeds. The controller has to be treated as new > + one. Use this command for a fully configured controller only when > + you really know what you are doing. > + > + This command generates a Command Complete event on success or a > + Command Status event on failure. > + > + Possible errors: Rejected > + Not Supported > + Invalid Parameters > + Invalid Index > + > + > Command Complete Event > ====================== > > -- > 2.29.2 >
