Hi Kiran,
On Thu, Oct 1, 2020 at 11:58 PM Kiran K <kiraank@xxxxxxxxx> wrote:
>
> From: Kiran K <kiraank@xxxxxxxxx>
>
> 1) add a helper function to download firmware
>
> 2) add a function to construct firmware / ddc file name
>
> 3) add a flag to identify new geneeration Intel controllers
>
> 4) define *setup* and hook it up for new genertion Intel controllers
>
> 5) map Typhoon Peak controller (PID:0x0032) to new generation controller
Instead of enumerating the changes here it would probably make more
sense to have them as separate patches.
> Signed-off-by: Kiran K <kiran.k@xxxxxxxxx>
> Signed-off-by: Amit K Bag <amit.k.bag@xxxxxxxxx>
> Signed-off-by: Raghuram Hegde <raghuram.hegde@xxxxxxxxx>
> Reviewed-by: Sathish Narasimman <Sathish.Narasimman@xxxxxxxxx>
> Reviewed-by: Chethan T N <chethan.tumkur.narayan@xxxxxxxxx>
> Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@xxxxxxxxx>
> ---
> drivers/bluetooth/btintel.h | 6 +
> drivers/bluetooth/btusb.c | 324 +++++++++++++++++++++++++++++++++++++++++++-
> 2 files changed, 328 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/bluetooth/btintel.h b/drivers/bluetooth/btintel.h
> index 09346ae..c4e28a8 100644
> --- a/drivers/bluetooth/btintel.h
> +++ b/drivers/bluetooth/btintel.h
> @@ -132,6 +132,12 @@ struct intel_debug_features {
> __u8 page1[16];
> } __packed;
>
> +#define INTEL_HW_PLATFORM(cnvx_bt) ((u8)(((cnvx_bt) & 0x0000ff00) >> 8))
> +#define INTEL_HW_VARIANT(cnvx_bt) ((u8)(((cnvx_bt) & 0x003f0000) >> 16))
> +#define INTEL_CNVX_TOP_TYPE(cnvx_top) ((cnvx_top) & 0x00000fff)
> +#define INTEL_CNVX_TOP_STEP(cnvx_top) (((cnvx_top) & 0x0f000000) >> 24)
> +#define INTEL_CNVX_TOP_PACK_SWAB(t, s) __swab16(((__u16)(((t) << 4) | (s))))
> +
> #if IS_ENABLED(CONFIG_BT_INTEL)
>
> int btintel_check_bdaddr(struct hci_dev *hdev);
> diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
> index 1005b6e..5e51749 100644
> --- a/drivers/bluetooth/btusb.c
> +++ b/drivers/bluetooth/btusb.c
> @@ -60,6 +60,7 @@ static struct usb_driver btusb_driver;
> #define BTUSB_WIDEBAND_SPEECH 0x400000
> #define BTUSB_VALID_LE_STATES 0x800000
> #define BTUSB_QCA_WCN6855 0x1000000
> +#define BTUSB_INTEL_NEWGEN 0x2000000
I wonder if it is a good idea to keep adding such flags per model
here, it should be possible to pass the pid/vid so we don't have to
add generation after generation here.
>
> static const struct usb_device_id btusb_table[] = {
> /* Generic Bluetooth USB device */
> @@ -365,7 +366,7 @@ static const struct usb_device_id blacklist_table[] = {
> BTUSB_WIDEBAND_SPEECH },
> { USB_DEVICE(0x8087, 0x0029), .driver_info = BTUSB_INTEL_NEW |
> BTUSB_WIDEBAND_SPEECH },
> - { USB_DEVICE(0x8087, 0x0032), .driver_info = BTUSB_INTEL_NEW |
> + { USB_DEVICE(0x8087, 0x0032), .driver_info = BTUSB_INTEL_NEWGEN |
> BTUSB_WIDEBAND_SPEECH},
> { USB_DEVICE(0x8087, 0x07da), .driver_info = BTUSB_CSR },
> { USB_DEVICE(0x8087, 0x07dc), .driver_info = BTUSB_INTEL },
> @@ -2359,6 +2360,181 @@ static bool btusb_setup_intel_new_get_fw_name(struct intel_version *ver,
> return true;
> }
>
> +static void btusb_setup_intel_newgen_get_fw_name(const struct intel_version_tlv *ver_tlv,
> + char *fw_name, size_t len,
> + const char *suffix)
> +{
> + /* The firmware file name for new generation controllers will be
> + * ibt-<cnvi_top type+cnvi_top step>-<cnvr_top type+cnvr_top step>
> + */
> + snprintf(fw_name, len, "intel/ibt-%04x-%04x.%s",
> + INTEL_CNVX_TOP_PACK_SWAB(INTEL_CNVX_TOP_TYPE(ver_tlv->cnvi_top),
> + INTEL_CNVX_TOP_STEP(ver_tlv->cnvi_top)),
> + INTEL_CNVX_TOP_PACK_SWAB(INTEL_CNVX_TOP_TYPE(ver_tlv->cnvr_top),
> + INTEL_CNVX_TOP_STEP(ver_tlv->cnvr_top)),
> + suffix);
> +}
> +
> +static int btusb_intel_download_firmware_newgen(struct hci_dev *hdev,
> + struct intel_version_tlv *ver,
> + u32 *boot_param)
> +{
> + const struct firmware *fw;
> + char fwname[64];
> + int err;
> + struct btusb_data *data = hci_get_drvdata(hdev);
> +
> + if (!ver || !boot_param)
> + return -EINVAL;
> +
> + /* The hardware platform number has a fixed value of 0x37 and
> + * for now only accept this single value.
> + */
> + if (INTEL_HW_PLATFORM(ver->cnvi_bt) != 0x37) {
> + bt_dev_err(hdev, "Unsupported Intel hardware platform (0x%2x)",
> + INTEL_HW_PLATFORM(ver->cnvi_bt));
> + return -EINVAL;
> + }
> +
> + /* The firmware variant determines if the device is in bootloader
> + * mode or is running operational firmware. The value 0x03 identifies
> + * the bootloader and the value 0x23 identifies the operational
> + * firmware.
> + *
> + * When the operational firmware is already present, then only
> + * the check for valid Bluetooth device address is needed. This
> + * determines if the device will be added as configured or
> + * unconfigured controller.
> + *
> + * It is not possible to use the Secure Boot Parameters in this
> + * case since that command is only available in bootloader mode.
> + */
> + if (ver->img_type == 0x03) {
> + clear_bit(BTUSB_BOOTLOADER, &data->flags);
> + btintel_check_bdaddr(hdev);
> + return 0;
> + }
> +
> + /* Check for supported iBT hardware variants of this firmware
> + * loading method.
> + *
> + * This check has been put in place to ensure correct forward
> + * compatibility options when newer hardware variants come along.
> + */
> + switch (INTEL_HW_VARIANT(ver->cnvi_bt)) {
> + case 0x17: /* TyP */
> + case 0x18: /* Slr */
> + case 0x19: /* Slr-F */
> + break;
> + default:
> + bt_dev_err(hdev, "Unsupported Intel hardware variant (0x%x)",
> + INTEL_HW_VARIANT(ver->cnvi_bt));
> + return -EINVAL;
> + }
> +
> + /* If the device is not in bootloader mode, then the only possible
> + * choice is to return an error and abort the device initialization.
> + */
> + if (ver->img_type != 0x01) {
> + bt_dev_err(hdev, "Unsupported Intel firmware variant (0x%x)",
> + ver->img_type);
> + return -ENODEV;
> + }
> +
> + /* It is required that every single firmware fragment is acknowledged
> + * with a command complete event. If the boot parameters indicate
> + * that this bootloader does not send them, then abort the setup.
> + */
> + if (ver->limited_cce != 0x00) {
> + bt_dev_err(hdev, "Unsupported Intel firmware loading method (0x%x)",
> + ver->limited_cce);
> + return -EINVAL;
> + }
> +
> + /* Secure boot engine type should be either 1 (ECDSA) or 0 (RSA) */
> + if (ver->sbe_type > 0x01) {
> + bt_dev_err(hdev, "Unsupported Intel secure boot engine type (0x%x)",
> + ver->sbe_type);
> + return -EINVAL;
> + }
> +
> + /* If the OTP has no valid Bluetooth device address, then there will
> + * also be no valid address for the operational firmware.
> + */
> + if (!bacmp(&ver->otp_bd_addr, BDADDR_ANY)) {
> + bt_dev_info(hdev, "No device address configured");
> + set_bit(HCI_QUIRK_INVALID_BDADDR, &hdev->quirks);
> + }
> +
> + btusb_setup_intel_newgen_get_fw_name(ver, fwname, sizeof(fwname), "sfi");
> + err = request_firmware(&fw, fwname, &hdev->dev);
> + if (err < 0) {
> + bt_dev_err(hdev, "Failed to load Intel firmware file (%d)", err);
> + return err;
> + }
> +
> + bt_dev_info(hdev, "Found device firmware: %s", fwname);
> +
> + if (fw->size < 644) {
> + bt_dev_err(hdev, "Invalid size of firmware file (%zu)",
> + fw->size);
> + err = -EBADF;
> + goto done;
> + }
> +
> + set_bit(BTUSB_DOWNLOADING, &data->flags);
> +
> + /* Start firmware downloading and get boot parameter */
> + err = btintel_download_firmware_newgen(hdev, fw, boot_param,
> + INTEL_HW_VARIANT(ver->cnvi_bt),
> + ver->sbe_type);
> + if (err < 0) {
> + /* When FW download fails, send Intel Reset to retry
> + * FW download.
> + */
> + btintel_reset_to_bootloader(hdev);
> + goto done;
> + }
> + set_bit(BTUSB_FIRMWARE_LOADED, &data->flags);
> +
> + bt_dev_info(hdev, "Waiting for firmware download to complete");
> +
> + /* Before switching the device into operational mode and with that
> + * booting the loaded firmware, wait for the bootloader notification
> + * that all fragments have been successfully received.
> + *
> + * When the event processing receives the notification, then the
> + * BTUSB_DOWNLOADING flag will be cleared.
> + *
> + * The firmware loading should not take longer than 5 seconds
> + * and thus just timeout if that happens and fail the setup
> + * of this device.
> + */
> + err = wait_on_bit_timeout(&data->flags, BTUSB_DOWNLOADING,
> + TASK_INTERRUPTIBLE,
> + msecs_to_jiffies(5000));
> + if (err == -EINTR) {
> + bt_dev_err(hdev, "Firmware loading interrupted");
> + goto done;
> + }
> +
> + if (err) {
> + bt_dev_err(hdev, "Firmware loading timeout");
> + err = -ETIMEDOUT;
> + btintel_reset_to_bootloader(hdev);
> + goto done;
> + }
> +
> + if (test_bit(BTUSB_FIRMWARE_FAILED, &data->flags)) {
> + bt_dev_err(hdev, "Firmware loading failed");
> + err = -ENOEXEC;
> + goto done;
> + }
> +
> +done:
> + release_firmware(fw);
> + return err;
> +}
> static int btusb_intel_download_firmware(struct hci_dev *hdev,
> struct intel_version *ver,
> struct intel_boot_params *params,
> @@ -2693,6 +2869,135 @@ static int btusb_setup_intel_new(struct hci_dev *hdev)
> return 0;
> }
>
> +static int btusb_setup_intel_newgen(struct hci_dev *hdev)
> +{
> + struct btusb_data *data = hci_get_drvdata(hdev);
> + u32 boot_param;
> + char ddcname[64];
> + ktime_t calltime, delta, rettime;
> + unsigned long long duration;
> + int err;
> + struct intel_debug_features features;
> + struct intel_version_tlv version;
> +
> + BT_DBG("%s", hdev->name);
> +
> + /* Set the default boot parameter to 0x0 and it is updated to
> + * SKU specific boot parameter after reading Intel_Write_Boot_Params
> + * command while downloading the firmware.
> + */
> + boot_param = 0x00000000;
> +
> + calltime = ktime_get();
> +
> + /* Read the Intel version information to determine if the device
> + * is in bootloader mode or if it already has operational firmware
> + * loaded.
> + */
> + err = btintel_read_version_tlv(hdev, &version);
> + if (err) {
> + bt_dev_err(hdev, "Intel Read version failed (%d)", err);
> + btintel_reset_to_bootloader(hdev);
> + return err;
> + }
> +
> + btintel_version_info_tlv(hdev, &version);
> +
> + err = btusb_intel_download_firmware_newgen(hdev, &version, &boot_param);
> + if (err)
> + return err;
> +
> + /* check if controller is already having an operational firmware */
> + if (version.img_type == 0x03)
> + goto finish;
> +
> + rettime = ktime_get();
> + delta = ktime_sub(rettime, calltime);
> + duration = (unsigned long long)ktime_to_ns(delta) >> 10;
> +
> + bt_dev_info(hdev, "Firmware loaded in %llu usecs", duration);
> +
> + calltime = ktime_get();
> +
> + set_bit(BTUSB_BOOTING, &data->flags);
> +
> + err = btintel_send_intel_reset(hdev, boot_param);
> + if (err) {
> + bt_dev_err(hdev, "Intel Soft Reset failed (%d)", err);
> + btintel_reset_to_bootloader(hdev);
> + return err;
> + }
> +
> + /* The bootloader will not indicate when the device is ready. This
> + * is done by the operational firmware sending bootup notification.
> + *
> + * Booting into operational firmware should not take longer than
> + * 1 second. However if that happens, then just fail the setup
> + * since something went wrong.
> + */
> + bt_dev_info(hdev, "Waiting for device to boot");
> +
> + err = wait_on_bit_timeout(&data->flags, BTUSB_BOOTING,
> + TASK_INTERRUPTIBLE,
> + msecs_to_jiffies(1000));
> +
> + if (err == -EINTR) {
> + bt_dev_err(hdev, "Device boot interrupted");
> + return -EINTR;
> + }
> +
> + if (err) {
> + bt_dev_err(hdev, "Device boot timeout");
> + btintel_reset_to_bootloader(hdev);
> + return -ETIMEDOUT;
> + }
> +
> + rettime = ktime_get();
> + delta = ktime_sub(rettime, calltime);
> + duration = (unsigned long long)ktime_to_ns(delta) >> 10;
> +
> + bt_dev_info(hdev, "Device booted in %llu usecs", duration);
> +
> + clear_bit(BTUSB_BOOTLOADER, &data->flags);
> +
> + btusb_setup_intel_newgen_get_fw_name(&version, ddcname, sizeof(ddcname),
> + "ddc");
> +
> + /* Once the device is running in operational mode, it needs to
> + * apply the device configuration (DDC) parameters.
> + *
> + * The device can work without DDC parameters, so even if it
> + * fails to load the file, no need to fail the setup.
> + */
> + btintel_load_ddc_config(hdev, ddcname);
> +
> + /* Read the Intel supported features and if new exception formats
> + * supported, need to load the additional DDC config to enable.
> + */
> + btintel_read_debug_features(hdev, &features);
> +
> + /* Set DDC mask for available debug features */
> + btintel_set_debug_features(hdev, &features);
> +
> + /* Read the Intel version information after loading the FW */
> + err = btintel_read_version_tlv(hdev, &version);
> + if (err)
> + return err;
> +
> + btintel_version_info_tlv(hdev, &version);
> +
> +finish:
> + /* Set the event mask for Intel specific vendor events. This enables
> + * a few extra events that are useful during general operation. It
> + * does not enable any debugging related events.
> + *
> + * The device will function correctly without these events enabled
> + * and thus no need to fail the setup.
> + */
> + btintel_set_event_mask(hdev, false);
> +
> + return 0;
> +}
> static int btusb_shutdown_intel(struct hci_dev *hdev)
> {
> struct sk_buff *skb;
> @@ -3969,7 +4274,8 @@ static int btusb_probe(struct usb_interface *intf,
> init_usb_anchor(&data->ctrl_anchor);
> spin_lock_init(&data->rxlock);
>
> - if (id->driver_info & BTUSB_INTEL_NEW) {
> + if ((id->driver_info & BTUSB_INTEL_NEW) ||
> + (id->driver_info & BTUSB_INTEL_NEWGEN)) {
> data->recv_event = btusb_recv_event_intel;
> data->recv_bulk = btusb_recv_bulk_intel;
> set_bit(BTUSB_BOOTLOADER, &data->flags);
> @@ -4078,6 +4384,20 @@ static int btusb_probe(struct usb_interface *intf,
> set_bit(HCI_QUIRK_NON_PERSISTENT_DIAG, &hdev->quirks);
> }
>
> + if (id->driver_info & BTUSB_INTEL_NEWGEN) {
> + hdev->manufacturer = 2;
> + hdev->send = btusb_send_frame_intel;
> + hdev->setup = btusb_setup_intel_newgen;
> + hdev->shutdown = btusb_shutdown_intel_new;
> + hdev->hw_error = btintel_hw_error;
> + hdev->set_diag = btintel_set_diag;
> + hdev->set_bdaddr = btintel_set_bdaddr;
> + hdev->cmd_timeout = btusb_intel_cmd_timeout;
> + set_bit(HCI_QUIRK_STRICT_DUPLICATE_FILTER, &hdev->quirks);
> + set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
> + set_bit(HCI_QUIRK_NON_PERSISTENT_DIAG, &hdev->quirks);
> + }
> +
> if (id->driver_info & BTUSB_MARVELL)
> hdev->set_bdaddr = btusb_set_bdaddr_marvell;
>
> --
> 2.7.4
>
--
Luiz Augusto von Dentz
