Re: [Bluez PATCH v2] doc: Add Suspend and Resume events

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Marcel,

Please take a look at this v2 patch.

Thanks
Abhishek

On Tue, Jul 14, 2020 at 12:51 PM Abhishek Pandit-Subedi
<abhishekpandit@xxxxxxxxxxxx> wrote:
>
> Add Controller Suspend Event and Controller Resume Event to identify
> suspend or resume of the Bluetooth stack has occurred.
>
> Also update Device Disconnected Event to indicate a new disconnect
> reason: "Connection terminated by local host for suspend"
>
> Reviewed-by: Alain Michaud <alainm@xxxxxxxxxxxx>
> Reviewed-by: Miao-chen Chou <mcchou@xxxxxxxxxxxx>
> ---
>
> Changes in v2:
> - Moved Wake_Reason to first value
> - Reduced Wake_Reason to not Bluetooth, unexpected event and remote wake
>
>  doc/mgmt-api.txt | 48 ++++++++++++++++++++++++++++++++++++++++++++++++
>  1 file changed, 48 insertions(+)
>
> diff --git a/doc/mgmt-api.txt b/doc/mgmt-api.txt
> index ca0d38469..e7a713824 100644
> --- a/doc/mgmt-api.txt
> +++ b/doc/mgmt-api.txt
> @@ -3834,6 +3834,7 @@ Device Disconnected Event
>                 2       Connection terminated by local host
>                 3       Connection terminated by remote host
>                 4       Connection terminated due to authentication failure
> +               5       Connection terminated by local host for suspend
>
>         Note that the local/remote distinction just determines which side
>         terminated the low-level connection, regardless of the
> @@ -4577,3 +4578,50 @@ Advertisement Monitor Removed Event
>
>         The event will only be sent to management sockets other than the
>         one through which the command was sent.
> +
> +
> +Controller Suspend Event
> +========================
> +
> +       Event code:             0x002d
> +       Controller Index:       <controller_id>
> +       Event Parameters:       Suspend_State (1 octet)
> +
> +       This event indicates that the controller is suspended for host suspend.
> +
> +       Possible values for the Suspend_State parameter:
> +               0       Running (not disconnected)
> +               1       Disconnected and not scanning
> +               2       Page scanning and/or passive scanning.
> +
> +       The value 0 is used for the running state and may be sent if the
> +       controller could not be configured to suspend properly.
> +
> +       This event will be sent to all management sockets.
> +
> +
> +Controller Resume Event
> +=======================
> +
> +       Event code:             0x002e
> +       Controller Index:       <controller_id>
> +       Event Parameters:       Wake_Reason (1 octet)
> +                               Address (6 octets)
> +                               Address_Type (1 octet)
> +
> +       This event indicates that the controller has resumed from suspend.
> +
> +       Possible values for the Wake_Reason parameter:
> +               0       Resume from non-Bluetooth wake source
> +               1       Wake due to unexpected event
> +               2       Remote wake due to peer device connection
> +
> +       Currently, we expect that only peer reconnections should wake us from
> +       the suspended state. Any other events that occurred while the system
> +       should have been suspended results in wake due to unexpected event.
> +
> +       If the Wake_Reason is Remote wake due to connection, the address of the
> +       peer device that caused the event will be shared in Address and
> +       Address_Type. Otherwise, Address and Address_Type will both be zero.
> +
> +       This event will be sent to all management sockets.
> --
> 2.27.0.389.gc38d7665816-goog
>



[Index of Archives]     [Bluez Devel]     [Linux Wireless Networking]     [Linux Wireless Personal Area Networking]     [Linux ATH6KL]     [Linux USB Devel]     [Linux Media Drivers]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Big List of Linux Books]

  Powered by Linux