Hi Hsin-Yu, > Bluetooth PTS test case HFP/AG/ACC/BI-12-I accepts SCO connection > with invalid parameter at the first SCO request expecting AG to > attempt another SCO request with the use of "safe settings" for > given codec, base on section 5.7.1.2 of HFP 1.7 specification. > > This patch addresses it by adding "Invalid LMP Parameters" (0x1e) > to the SCO fallback case. Verified with below log: > > < HCI Command: Setup Synchronous Connection (0x01|0x0028) plen 17 > Handle: 256 > Transmit bandwidth: 8000 > Receive bandwidth: 8000 > Max latency: 13 > Setting: 0x0003 > Input Coding: Linear > Input Data Format: 1's complement > Input Sample Size: 8-bit > # of bits padding at MSB: 0 > Air Coding Format: Transparent Data > Retransmission effort: Optimize for link quality (0x02) > Packet type: 0x0380 > 3-EV3 may not be used > 2-EV5 may not be used > 3-EV5 may not be used >> HCI Event: Command Status (0x0f) plen 4 > Setup Synchronous Connection (0x01|0x0028) ncmd 1 > Status: Success (0x00) >> HCI Event: Number of Completed Packets (0x13) plen 5 > Num handles: 1 > Handle: 256 > Count: 1 >> HCI Event: Max Slots Change (0x1b) plen 3 > Handle: 256 > Max slots: 1 >> HCI Event: Synchronous Connect Complete (0x2c) plen 17 > Status: Invalid LMP Parameters / Invalid LL Parameters (0x1e) > Handle: 0 > Address: 00:1B:DC:F2:21:59 (OUI 00-1B-DC) > Link type: eSCO (0x02) > Transmission interval: 0x00 > Retransmission window: 0x02 > RX packet length: 0 > TX packet length: 0 > Air mode: Transparent (0x03) > < HCI Command: Setup Synchronous Connection (0x01|0x0028) plen 17 > Handle: 256 > Transmit bandwidth: 8000 > Receive bandwidth: 8000 > Max latency: 8 > Setting: 0x0003 > Input Coding: Linear > Input Data Format: 1's complement > Input Sample Size: 8-bit > # of bits padding at MSB: 0 > Air Coding Format: Transparent Data > Retransmission effort: Optimize for link quality (0x02) > Packet type: 0x03c8 > EV3 may be used > 2-EV3 may not be used > 3-EV3 may not be used > 2-EV5 may not be used > 3-EV5 may not be used >> HCI Event: Command Status (0x0f) plen 4 > Setup Synchronous Connection (0x01|0x0028) ncmd 1 > Status: Success (0x00) >> HCI Event: Max Slots Change (0x1b) plen 3 > Handle: 256 > Max slots: 5 >> HCI Event: Max Slots Change (0x1b) plen 3 > Handle: 256 > Max slots: 1 >> HCI Event: Synchronous Connect Complete (0x2c) plen 17 > Status: Success (0x00) > Handle: 257 > Address: 00:1B:DC:F2:21:59 (OUI 00-1B-DC) > Link type: eSCO (0x02) > Transmission interval: 0x06 > Retransmission window: 0x04 > RX packet length: 30 > TX packet length: 30 > Air mode: Transparent (0x03) > > Signed-off-by: Hsin-Yu Chao <hychao@xxxxxxxxxxxx> > --- > net/bluetooth/hci_event.c | 1 + > 1 file changed, 1 insertion(+) patch has been applied to bluetooth-next tree. Regards Marcel
