Hi Luiz, There are some headsets that configure the MTU to 850(3M PHY) and then under some situation(noisy), it switches to 2M PHY packets for A2DP playback. The reason behind this is their receiver's capability for better demodulation with QDPSK(2M PHY) when compared to 8DPSK(3M PHY). >From Bluetooth specification, the remote device can request the LMP_preferred_rate with the LMP command to switch to 2M. When Baseband PHY is 2M, the maximum possible packet type is 2DH5 which can hold 679 bytes ( 672 bytes of L2CAP MTU excluding the baseband headers). When L2CAP MTU for an A2DP packet is larger than 672 bytes, it happens to use 2 Baseband packets to deliver the L2CAP packet ie., like 1 2DH5(679 bytes) and 1 2DH3(171 bytes) packet to deliver 850 bytes of AVDTP Media. The is not efficient baseband utilization when the number of baseband ACL buffers used 2 no.s or even less that may lead to the delivery of one L2CAP packet that may take 4 slots more ( 2.5 ms more). When the remote device ( headset) has less number of baseband ACL buffers and Host(source) is aggressively delivering the audio data to render, it shall end up in a condition where the remote device does Flow OFF that shall make the Source device to wait until next FLOW ON send from the headset device. This kind of situation shall end up accumulating more buffers and FLOW ON/OFF become cyclic and leads to an audio break. Is there a better solution to overcome this issue? We considered changing the HOST MTU to 672bytes to overcome this issue that makes the remote headset device to use 2M. And found that the test results are positive. On Wed, Dec 18, 2019 at 5:49 AM Luiz Augusto von Dentz <luiz.dentz@xxxxxxxxx> wrote: > > Hi Chethan, > > On Mon, Dec 16, 2019 at 10:40 PM chethan tn <chethantn@xxxxxxxxx> wrote: > > > > Hi, > > > > I would like to understand why the Source device L2CAP mtu is always > > set to the remote device mtu during L2CAP connection? > > > > https://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth.git/tree/net/bluetooth/l2cap_core.c#n3370 > > https://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth.git/tree/net/bluetooth/l2cap_core.c#n3474 > > > > > > > > I tried to set the specific MTU for specific profile connection( For > > Ex: A2DP connection - PSM 25) patch mentioned below, but the same is > > not reflected because of the below code. > > > > https://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth.git/tree/net/bluetooth/l2cap_core.c#n3474 > > The answer is pretty simple, we don't control the remote/output MTU, > so we cannot force the remote to use some arbitrary MTU if it doesn't > agree with. > > > Here the patch to set the MTU from the use space bluez. > > > > diff --git a/profiles/audio/a2dp.c b/profiles/audio/a2dp.c > > index 58e1534a4..7d8a718c0 100644 > > --- a/profiles/audio/a2dp.c > > +++ b/profiles/audio/a2dp.c > > @@ -1573,6 +1573,7 @@ static bool a2dp_server_listen(struct a2dp_server *server) > > BT_IO_OPT_SOURCE_BDADDR, > > btd_adapter_get_address(server->adapter), > > BT_IO_OPT_PSM, AVDTP_PSM, > > + BT_IO_OPT_OMTU, AVDTP_MTU, > > BT_IO_OPT_SEC_LEVEL, BT_IO_SEC_MEDIUM, > > BT_IO_OPT_MASTER, true, > > BT_IO_OPT_INVALID); > > diff --git a/profiles/audio/avdtp.c b/profiles/audio/avdtp.c > > index 51ead684a..786702cec 100644 > > --- a/profiles/audio/avdtp.c > > +++ b/profiles/audio/avdtp.c > > @@ -2394,6 +2394,7 @@ static GIOChannel *l2cap_connect(struct avdtp *session) > > BT_IO_OPT_DEST_BDADDR, > > device_get_address(session->device), > > BT_IO_OPT_PSM, AVDTP_PSM, > > + BT_IO_OPT_OMTU, AVDTP_MTU, > > BT_IO_OPT_SEC_LEVEL, BT_IO_SEC_MEDIUM, > > BT_IO_OPT_INVALID); > > if (!io) { > > diff --git a/profiles/audio/avdtp.h b/profiles/audio/avdtp.h > > index 621a6e3cf..372b2579d 100644 > > --- a/profiles/audio/avdtp.h > > +++ b/profiles/audio/avdtp.h > > > > > > > > Can you please suggest what is the best way to set the L2CAP mtu as > > user defined. > > > > > > Thanks > > > > Chethan > > > > -- > Luiz Augusto von Dentz Regards Sathish N
