Hi Pali,
On Thu, May 16, 2019 at 9:34 PM Pali Rohár <pali.rohar@xxxxxxxxx> wrote:
>
> Ping, can you comment anything related to hardcoded bandwidth?
>
> I would really like to take next step how to expose API for changing
> bandwidth as linux kernel currently does not allow to receive and
> transmit voice encoded by AuriStream codec.
Didn't even know such codec existed, anyway that is not using the
standard AT commands so it is kind hard to figure out how to set it up
properly, to be honest, I would rather see WBS implementation finally
reach PA before we start digging into this.
> On Monday 06 May 2019 17:16:51 Pali Rohár wrote:
> > Ccing more people...
> >
> > do you have idea why for custom SCO HFP codec is needed to change
> > Transmit and Receive bandwidth in HCI Setup Synchronous Connection
> > packet?
> >
> > And how to expose API for userspace applications so they can change
> > hardcoded kernel bandwidth? Why is there value 8000?
> >
> > Without changing hardcoded value 8000 to 4000 I'm unable to open SCO
> > socket for AuriStream codec in HFP profile.
> >
> > On Saturday 04 May 2019 19:15:50 Pali Rohár wrote:
> > > Hello,
> > >
> > > I found out that more bluetooth headsets supports AuriStream codec in
> > > bluetooth HSP/HFP profile. It is proprietary CSR codec described as some
> > > ADPCM variant with better quality as default CVSD codec.
> > >
> > > Headset announce their support by sending command AT+CSRSF, in sixth
> > > number with first or second bit set (counted from zero). E.g.:
> > >
> > > AT+CSRSF=0,0,0,0,0,7
> > >
> > > Codec is then selected by host with sending:
> > >
> > > +CSRFN: (6,4)
> > > OK
> > >
> > > And answer from headset is acknowledged by another:
> > >
> > > OK
> > >
> > >
> > > Problem is that on Linux after issuing these AT commands I cannot longer
> > > connect to SCO socket. connect() fails with Protocol Error.
> > >
> > > And in btmon is following error:
> > >
> > > > HCI Event: Synchronous Connect Complete (0x2c) plen 17
> > > Status: Invalid LMP Parameters / Invalid LL Parameters (0x1e)
> > >
> > >
> > > In some CSR SKD is example how to activate it and there is code which
> > > seems to sets following HCI connection parameters:
> > >
> > > syncPktTypes = 0x003F
> > > bandwidth = 4000
> > > max_latency = 16
> > > voice_settings = 0x63
> > > retx_effort = 2
> > >
> > > I figured out that voice_settings can be configured via setsockopt()
> > > SOL_BLUETOOTH + BT_VOICE. But for some unknown reason linux kernel
> > > accept only two whitelisted values: 0x0003 and 0x0060.
> > >
> > > So I tried to set 0x0003 value (BT_VOICE_TRANSPARENT).
> > >
> > > In btmon I saw that kernel really changed "Air Coding Format" from CVSD
> > > to Transparent, but I still got same "Invalid LMP Parameters" error.
> > >
> > > I tried to remove that whilelist from BT_VOICE option via patch below:
> > >
> > > diff --git a/net/bluetooth/sco.c b/net/bluetooth/sco.c
> > > index 9a580999ca57..06db91de4f23 100644
> > > --- a/net/bluetooth/sco.c
> > > +++ b/net/bluetooth/sco.c
> > > @@ -231,7 +231,7 @@ static int sco_connect(struct sock *sk)
> > > else
> > > type = SCO_LINK;
> > >
> > > - if (sco_pi(sk)->setting == BT_VOICE_TRANSPARENT &&
> > > + if ((sco_pi(sk)->setting & SCO_AIRMODE_MASK) == SCO_AIRMODE_TRANSP &&
> > > (!lmp_transp_capable(hdev) || !lmp_esco_capable(hdev))) {
> > > err = -EOPNOTSUPP;
> > > goto done;
> > > @@ -836,13 +836,6 @@ static int sco_sock_setsockopt(struct socket *sock, int level, int optname,
> > > break;
> > > }
> > >
> > > - /* Explicitly check for these values */
> > > - if (voice.setting != BT_VOICE_TRANSPARENT &&
> > > - voice.setting != BT_VOICE_CVSD_16BIT) {
> > > - err = -EINVAL;
> > > - break;
> > > - }
> > > -
> > > sco_pi(sk)->setting = voice.setting;
> > > break;
> > >
> > >
> > > Btmon now really showed Settings as 0x63, but still did not worked.
> > > Again exactly same HCI error.
> > >
> > > Next I tried hacking linux kernel to customize packet type and max
> > > latency. But even I changed these values I still got that HCI error.
> > >
> > > After I changed tx_bandwidth and rx_bandwidth to 4000 (as described in
> > > above connection parameters), connect() syscall for that SCO socket
> > > succeeded and I started getting voice microphone data on that socket.
> > >
> > > And it worked also with voice settings 0x0003 with active in-kernel
> > > whitelist.
> > >
> > > Patch which is needed is following: Change bandwidth to 4000:
> > >
> > > diff --git a/net/bluetooth/hci_conn.c b/net/bluetooth/hci_conn.c
> > > index bd4978ce8c45..2dd4d0412971 100644
> > > --- a/net/bluetooth/hci_conn.c
> > > +++ b/net/bluetooth/hci_conn.c
> > > @@ -283,8 +283,8 @@ bool hci_setup_sync(struct hci_conn *conn, __u16 handle)
> > >
> > > cp.handle = cpu_to_le16(handle);
> > >
> > > - cp.tx_bandwidth = cpu_to_le32(0x00001f40);
> > > - cp.rx_bandwidth = cpu_to_le32(0x00001f40);
> > > + cp.tx_bandwidth = cpu_to_le32(4000);
> > > + cp.rx_bandwidth = cpu_to_le32(4000);
> > > cp.voice_setting = cpu_to_le16(conn->setting);
> > >
> > > switch (conn->setting & SCO_AIRMODE_MASK) {
> > >
> > > I have really no idea what it does with headset. But without this patch
> > > I'm not able to switch HSP codec from CVSD to AuriStream.
> > >
> > > Is somebody able to explain how above change can allow opening SCO
> > > socket?
> > >
> > > Because without it I'm not able to activate AuriStream codec, could you
> > > consider allowing userspace (via some setsockoptň to change bandwidth?
> > > Because now it is hardcoded in kernel source code.
> > >
> > > For more details here is btmon output with default bandwidth which is
> > > failing:
> > >
> > > $ sudo ./monitor/btmon
> > > Bluetooth monitor ver 5.50
> > > = Note: Linux version 4.9.0-9-amd64 (x86_64)
> > > = Note: Bluetooth subsystem version 2.22
> > > = New Index: XX:XX:XX:XX:XX:XX (Primary,USB,hci0)
> > > = Open Index: XX:XX:XX:XX:XX:XX
> > > = Index Info: XX:XX:XX:XX:XX:XX (Intel Corp.)
> > > @ MGMT Open: bluetoothd (privileged) version 1.14
> > > @ MGMT Open: btmon (privileged) version 1.14
> > > < HCI Command: Setup Synchronous Connection (0x01|0x0028) plen 17
> > > Handle: 34
> > > Transmit bandwidth: 8000
> > > Receive bandwidth: 8000
> > > Max latency: 13
> > > Setting: 0x0003
> > > Input Coding: Linear
> > > Input Data Format: 1's complement
> > > Input Sample Size: 8-bit
> > > # of bits padding at MSB: 0
> > > Air Coding Format: Transparent Data
> > > Retransmission effort: Optimize for link quality (0x02)
> > > Packet type: 0x0380
> > > 3-EV3 may not be used
> > > 2-EV5 may not be used
> > > 3-EV5 may not be used
> > > > HCI Event: Command Status (0x0f) plen 4
> > > Setup Synchronous Connection (0x01|0x0028) ncmd 1
> > > Status: Success (0x00)
> > > > HCI Event: Max Slots Change (0x1b) plen 3
> > > Handle: 34
> > > Max slots: 1
> > > > HCI Event: Synchronous Connect Complete (0x2c) plen 17
> > > Status: Invalid LMP Parameters / Invalid LL Parameters (0x1e)
> > > Handle: 34
> > > Address: XX:XX:XX:XX:XX:XX (Creative Technology, Ltd.)
> > > Link type: eSCO (0x02)
> > > Transmission interval: 0x00
> > > Retransmission window: 0x00
> > > RX packet length: 0
> > > TX packet length: 0
> > > Air mode: u-law log (0x00)
> > > > HCI Event: Max Slots Change (0x1b) plen 3
> > > Handle: 34
> > > Max slots: 5
> > >
> > > And here is btmon output with above kernel patch which changes bandwidth to 4000:
> > >
> > > $ sudo ./monitor/btmon
> > > Bluetooth monitor ver 5.50
> > > = Note: Linux version 4.9.0-9-amd64 (x86_64)
> > > = Note: Bluetooth subsystem version 2.22
> > > = New Index: XX:XX:XX:XX:XX:XX (Primary,USB,hci0)
> > > = Open Index: XX:XX:XX:XX:XX:XX
> > > = Index Info: XX:XX:XX:XX:XX:XX (Intel Corp.)
> > > @ MGMT Open: bluetoothd (privileged) version 1.14
> > > @ MGMT Open: btmon (privileged) version 1.14
> > > < HCI Command: Setup Synchronous Connection (0x01|0x0028) plen 17
> > > Handle: 34
> > > Transmit bandwidth: 4000
> > > Receive bandwidth: 4000
> > > Max latency: 13
> > > Setting: 0x0003
> > > Input Coding: Linear
> > > Input Data Format: 1's complement
> > > Input Sample Size: 8-bit
> > > # of bits padding at MSB: 0
> > > Air Coding Format: Transparent Data
> > > Retransmission effort: Optimize for link quality (0x02)
> > > Packet type: 0x0380
> > > 3-EV3 may not be used
> > > 2-EV5 may not be used
> > > 3-EV5 may not be used
> > > > HCI Event: Command Status (0x0f) plen 4
> > > Setup Synchronous Connection (0x01|0x0028) ncmd 1
> > > Status: Success (0x00)
> > > > HCI Event: Max Slots Change (0x1b) plen 3
> > > Handle: 34
> > > Max slots: 1
> > > > HCI Event: Synchronous Connect Complete (0x2c) plen 17
> > > Status: Success (0x00)
> > > Handle: 38
> > > Address: XX:XX:XX:XX:XX:XX (Creative Technology, Ltd.)
> > > Link type: eSCO (0x02)
> > > Transmission interval: 0x10
> > > Retransmission window: 0x02
> > > RX packet length: 40
> > > TX packet length: 40
> > > Air mode: Transparent (0x03)
> > > < SCO Data TX: Handle 38 flags 0x00 dlen 48
> > > < ACL Data TX: Handle 34 flags 0x00 dlen 18
> > > Channel: 105 len 14 [PSM 0 mode 0] {chan 0}
> > > 61 ef 15 0d 0a 2b 56 47 4d 3d 34 0d 0a d4 a....+VGM=4...
> > > > HCI Event: Number of Completed Packets (0x13) plen 5
> > > Num handles: 1
> > > Handle: 34
> > > Count: 1
> > > > SCO Data RX: Handle 38 flags 0x00 dlen 24
> > > > SCO Data RX: Handle 38 flags 0x00 dlen 24
> > > > SCO Data RX: Handle 38 flags 0x00 dlen 24
> > > < SCO Data TX: Handle 38 flags 0x00 dlen 48
> > > > HCI Event: Max Slots Change (0x1b) plen 3
> > > Handle: 34
> > > Max slots: 5
> > >
> > > ... and SCO data are coming on SCO socket.
> > >
> >
>
> --
> Pali Rohár
> pali.rohar@xxxxxxxxx
--
Luiz Augusto von Dentz
