On 2019-01-15 06:50, Matthias Kaehlcke wrote:
> On Mon, Jan 14, 2019 at 09:21:25PM +0530, Balakrishna Godavarthi wrote:
> > On 2019-01-12 04:42, Matthias Kaehlcke wrote:
> > > On Fri, Jan 11, 2019 at 07:53:43PM +0530, Balakrishna Godavarthi wrote:
> > > > Hi Matthias,
> > > >
> > > > On 2019-01-11 02:13, Matthias Kaehlcke wrote:
> > > > > Hi Balakrishna,
> > > > >
> > > > > On Thu, Jan 10, 2019 at 08:30:43PM +0530, Balakrishna Godavarthi wrote:
> > > > > > Hi Matthias,
> > > > > >
> > > > > > On 2019-01-03 03:45, Matthias Kaehlcke wrote:
> > > > > > > On Mon, Dec 31, 2018 at 11:34:46AM +0530, Balakrishna Godavarthi wrote:
> > > > > > > > Hi Marcel,
> > > > > > > >
> > > > > > > > On 2018-12-30 13:40, Marcel Holtmann wrote:
> > > > > > > > > Hi Balakrishna,
> > > > > > > > >
> > > > > > > > > > > > Latest qualcomm chips are not sending an command complete event for
> > > > > > > > > > > > every firmware packet sent to chip. They only respond with a vendor
> > > > > > > > > > > > specific event for the last firmware packet. This optimization will
> > > > > > > > > > > > decrease the BT ON time. Due to this we are seeing a timeout error
> > > > > > > > > > > > message logs on the console during firmware download. Now we are
> > > > > > > > > > > > injecting a command complete event once we receive an vendor
> > > > > > > > > > > > specific
> > > > > > > > > > > > event for the last RAM firmware packet.
> > > > > > > > > > > > Signed-off-by: Balakrishna Godavarthi <bgodavar@xxxxxxxxxxxxxx>
> > > > > > > > > > > > ---
> > > > > > > > > > > > drivers/bluetooth/btqca.c | 39
> > > > > > > > > > > > ++++++++++++++++++++++++++++++++++++++-
> > > > > > > > > > > > drivers/bluetooth/btqca.h | 3 +++
> > > > > > > > > > > > 2 files changed, 41 insertions(+), 1 deletion(-)
> > > > > > > > > > > > diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
> > > > > > > > > > > > index ec9e03a6b778..0b533f65f652 100644
> > > > > > > > > > > > --- a/drivers/bluetooth/btqca.c
> > > > > > > > > > > > +++ b/drivers/bluetooth/btqca.c
> > > > > > > > > > > > @@ -144,6 +144,7 @@ static void qca_tlv_check_data(struct
> > > > > > > > > > > > rome_config *config,
> > > > > > > > > > > > * In case VSE is skipped, only the last segment is acked.
> > > > > > > > > > > > */
> > > > > > > > > > > > config->dnld_mode = tlv_patch->download_mode;
> > > > > > > > > > > > + config->dnld_type = config->dnld_mode;
> > > > > > > > > > > > BT_DBG("Total Length : %d bytes",
> > > > > > > > > > > > le32_to_cpu(tlv_patch->total_size));
> > > > > > > > > > > > @@ -264,6 +265,31 @@ static int qca_tlv_send_segment(struct
> > > > > > > > > > > > hci_dev *hdev, int seg_size,
> > > > > > > > > > > > return err;
> > > > > > > > > > > > }
> > > > > > > > > > > > +static int qca_inject_cmd_complete_event(struct hci_dev *hdev)
> > > > > > > > > > > > +{
> > > > > > > > > > > > + struct hci_event_hdr *hdr;
> > > > > > > > > > > > + struct hci_ev_cmd_complete *evt;
> > > > > > > > > > > > + struct sk_buff *skb;
> > > > > > > > > > > > +
> > > > > > > > > > > > + skb = bt_skb_alloc(sizeof(*hdr) + sizeof(*evt) + 1, GFP_KERNEL);
> > > > > > > > > > > > + if (!skb)
> > > > > > > > > > > > + return -ENOMEM;
> > > > > > > > > > > > +
> > > > > > > > > > > > + hdr = skb_put(skb, sizeof(*hdr));
> > > > > > > > > > > > + hdr->evt = HCI_EV_CMD_COMPLETE;
> > > > > > > > > > > > + hdr->plen = sizeof(*evt) + 1;
> > > > > > > > > > > > +
> > > > > > > > > > > > + evt = skb_put(skb, sizeof(*evt));
> > > > > > > > > > > > + evt->ncmd = 1;
> > > > > > > > > > > > + evt->opcode = HCI_OP_NOP;
> > > > > > >
> > > > > > > After looking a bit more at it I realize HCI_OP_NOP is not a good
> > > > > > > value in this case:
> > > > > > >
> > > > > > > static void hci_cmd_complete_evt(...)
> > > > > > > {
> > > > > > > ...
> > > > > > >
> > > > > > > if (*opcode != HCI_OP_NOP)
> > > > > > > cancel_delayed_work(&hdev->cmd_timer);
> > > > > > >
> > > > > > > ...
> > > > > > > }
> > > > > > >
> > > > > > > https://elixir.bootlin.com/linux/v4.19/source/net/bluetooth/hci_event.c#L3351
> > > > > > >
> > > > > > > Cancelling the command timeout is precisely what we want. Not sure why
> > > > > > > the patch with HCI_OP_NOP makes the timeouts go away in most cases
> > > > > > > (but not e.g. when inserting an msleep(1000) after downloading the
> > > > > > > NVM.
> > > > > > >
> > > > > > > I suggest to pass the opcode of the command to be completed.
> > > > > > >
> > > > > > > > > > > > +
> > > > > > > > > > > > + skb_put_u8(skb, QCA_HCI_CC_SUCCESS);
> > > > > > > > > > > > +
> > > > > > > > > > > > + hci_skb_pkt_type(skb) = HCI_EVENT_PKT;
> > > > > > > > > > > > +
> > > > > > > > > > > > + return hci_recv_frame(hdev, skb);
> > > > > > > > > > > > +}
> > > > > > > > > > > > +
> > > > > > > > > > > > static int qca_download_firmware(struct hci_dev *hdev,
> > > > > > > > > > > > struct rome_config *config)
> > > > > > > > > > > > {
> > > > > > > > > > > > @@ -297,11 +323,22 @@ static int
> > > > > > > > > > > > qca_download_firmware(struct hci_dev *hdev,
> > > > > > > > > > > > ret = qca_tlv_send_segment(hdev, segsize, segment,
> > > > > > > > > > > > config->dnld_mode);
> > > > > > > > > > > > if (ret)
> > > > > > > > > > > > - break;
> > > > > > > > > > > > + goto out;
> > > > > > > > > > > > segment += segsize;
> > > > > > > > > > > > }
> > > > > > > > > > > > + /* Latest qualcomm chipsets are not sending a command
> > > > > > > > > > > > complete event
> > > > > > > > > > > > + * for every fw packet sent. They only respond with a
> > > > > > > > > > > > vendor specific
> > > > > > > > > > > > + * event for the last packet. This optimization in the chip will
> > > > > > > > > > > > + * decrease the BT in initialization time. Here we will
> > > > > > > > > > > > inject a command
> > > > > > > > > > > > + * complete event to avoid a command timeout error message.
> > > > > > > > > > > > + */
> > > > > > > > > > > > + if ((config->dnld_type == ROME_SKIP_EVT_VSE_CC ||
> > > > > > > > > > > > + config->dnld_type == ROME_SKIP_EVT_VSE))
> > > > > > > > > > > > + return qca_inject_cmd_complete_event(hdev);
> > > > > > > > > > > > +
> > > > > > > > > > > have you actually considered using __hci_cmd_send in that case. It is
> > > > > > > > > > > allowed for vendor OGF to use that command. I see you actually do use
> > > > > > > > > > > it and now I am failing to understand what this is for.
> > > > > > > > > > [Bala]: thanks for reviewing the change.
> > > > > > > > > >
> > > > > > > > > > __hci_cmd_send() can be used only to send the command to the chip.
> > > > > > > > > > it will not wait for the response for the command sent.
> > > > > > > > > >
> > > > > > > > > > as you know that every vendor command sent to chip will respond with
> > > > > > > > > > vendor specific event and command complete event.
> > > > > > > > > > but in our case chip will only respond with vendor specific event
> > > > > > > > > > only. so we are injecting command complete event.
> > > > > > > > >
> > > > > > > > > and __hci_cmd_sync_ev is also not working for you? However since you
> > > > > > > > > are not waiting for the vendor event anyway and just injecting
> > > > > > > > > cmd_complete, I wonder what’s the difference in just using
> > > > > > > > > __hci_cmd_send and not bothering to wait or inject at all. I am
> > > > > > > > > failing to see where this injection makes a difference.
> > > > > > > > >
> > > > > > > > > For me it is a big difference if we are injecting one event like in
> > > > > > > > > the case of Intel compared to injecting one for every command. It will
> > > > > > > > > show a wrong picture in btmon and that is a bad idea.
> > > > > > > > >
> > > > > > > > > Regards
> > > > > > > > >
> > > > > > > > > Marcel
> > > > > > > >
> > > > > > > > [Bala]: here is the use case, when ever we download the fw packets
> > > > > > > > i.e. RAM
> > > > > > > > image, for every command sent(i.e. fw packet) from
> > > > > > > > the host chip will respond with an vendor specific event and command
> > > > > > > > complete event.
> > > > > > > >
> > > > > > > > the above is taking more time to setup the BT device. then we came
> > > > > > > > up with
> > > > > > > > solution where we enable flags in fw file (i.e. RAM image header)
> > > > > > > > whether to wait for event to be received or sent the total packets
> > > > > > > > and wait
> > > > > > > > for the events for the last packet.
> > > > > > > >
> > > > > > > > So currently we are handling both the cases in the code. i.e wait
> > > > > > > > for event
> > > > > > > > for all packet or wait for an event for the last packet.
> > > > > > > >
> > > > > > > > but in the second case i.e. wait for event for the last packet sent,
> > > > > > > > we are
> > > > > > > > only receiving an vendor specific event from chip which holds the
> > > > > > > > status of
> > > > > > > > fw download.
> > > > > > > >
> > > > > > > > so as __hci_cmd_sync_ev() requires an command complete event. so we
> > > > > > > > are
> > > > > > > > injecting it after the vendor specific event received for the last
> > > > > > > > packet.
> > > > > > > >
> > > > > > > > This helps to overcome 0xfc00 timeout error logging on console.
> > > > > > >
> > > > > > > Some more details:
> > > > > > >
> > > > > > > The timeout error is actually from reading the 'SoC version', which
> > > > > > > uses the same command code as the firmware download
> > > > > > > (EDL_PATCH_CMD_OPCODE). Without reading the 'SoC version' it would be
> > > > > > > from the command to write the first firmware segment.
> > > > > > >
> > > > > > > If the download of a firmware binary takes >= 2s (HCI_CMD_TIMEOUT) the
> > > > > > > timeout would still occur. If necessary this could be mitigated by
> > > > > > > injecting some command complete events during the firmware download,
> > > > > > > though I expect Marcel wouldn't be overly happy with that, since it
> > > > > > > would affect btmon even more.
> > > > > > >
> > > > > > > Regards
> > > > > > >
> > > > > > > Matthias
> > > > > >
> > > > > > [Bala]: Basically every vendor specific command we sent to chip,
> > > > > > chip should respond with an vendor specific event followed by an
> > > > > > command
> > > > > > complete event
> > > > > > or some times it will only respond with an command complete event.
> > > > > > but in any case command complete event is mandatory to all the
> > > > > > command we
> > > > > > sent to the chip.
> > > > >
> > > > > Is this ("command complete event is mandatory to all the command we
> > > > > sent to the chip") a description of what the chip actually does, or
> > > > > what it should be doing according to the spec?
> > > > >
> > > > > As mentioned earlier, the timeout we see originates from reading the
> > > > > SoC version:
> > > > >
> > > > > diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
> > > > > index 0b533f65f652fc..1e484e61799571 100644
> > > > > --- a/drivers/bluetooth/btqca.c
> > > > > +++ b/drivers/bluetooth/btqca.c
> > > > > @@ -400,6 +400,10 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t
> > > > > baudrate,
> > > > > return err;
> > > > > }
> > > > >
> > > > > + printk("DBG: ZZZzzzzzzz\n");
> > > > > + msleep(2500);
> > > > > + printk("DBG: good morning!\n");
> > > > > +
> > > > > /* Download NVM configuration */
> > > > > config.type = TLV_TYPE_NVM;
> > > > > if (soc_type == QCA_WCN3990)
> > > > >
> > > > > When you boot with this patch you'll see something like this:
> > > > >
> > > > > [ 15.531365] DBG: reading SoC version
> > > > > [ 15.544963] DBG: ZZZzzzzzzz
> > > > > [ 17.590282] Bluetooth: hci0: command 0xfc00 tx timeout
> > > > > [ 18.099110] DBG: good morning!
> > > > >
> > > >
> > > > [Bala]: my previous analysis were wrong. thanks for pointing me to the
> > > > correct issue.
> > > > i am able to see timeout after version command.(used some
> > > > sleep)
> > > > here is the reason for it.
> > > >
> > > > 01 00 fc 01 19 (we send the command to chip to request
> > > > version)
> > > > 04 ff 0e 00 02 0a 00 00 00 01 00 01 02 14 02 01 40(chip will
> > > > respond
> > > > with the vendor specific event payload will be chip version)
> > > > 04 0e 04 01 00 00 00(command complete event)
> > > >
> > > > issue is with command complete event. ideally command
> > > > complete event
> > > > payload holds the command for which chip sends command complete event.
> > > >
> > > > breaking the command
> > > >
> > > > 04 : event packet (fixed)
> > > > 0e : command complete event(fixed)
> > > > 04 : size of the payload,
> > > >
> > > > 01 : no of commands in the payload
> > > > 00 : OCF (opocde lsb)
> > > > 00 : OGF (opcode msb)
> > > > 00 : status of command executed,
> > > >
> > > > payload is form byte 4 to byte 7. which hold the command i.e
> > > > opcode
> > > > form the above response opcode is 0x0000. ideally this should be
> > > > 0xfc00
> > > > because the command complete response from the chip is for the
> > > > command
> > > > 0xfc00.
> > > >
> > > > Checked with Chip firmware dev team for the reason, it was an
> > > > limitation or an bug in the chip ROM firmware
> > > > in the current chipset, which is fixed in the coming chipset.
> > > >
> > > > so we expect the command 0xfc00 but recevuies 0x00. so that is
> > > > the
> > > > reason we see an timeouts.
> > > > for all the vendor commands we receive 0x0000 in the command
> > > > complete
> > > > event.
> > >
> > > Thanks for your analysis.
> > >
> > > It is unfortunate (though not unexpected) that this is a problem in
> > > the ROM were we can't fix it, but at least the FW team is aware of it
> > > and fixed it for future hardware.
> > >
> > > > if comes a new question how are we not seeing an 0xfc00 when
> > > > we inject
> > > > an command complete event.
> > > > i experimented this patch, when i inject the command complete
> > > > event
> > > > from the soc version still i can see the command timeouts.
> > >
> > > I don't see command timeouts when injecting a command complete event
> > > after reading the SoC version. I suspect you still use patch which
> > > injects a command complete event with HCI_OP_NOP, which is precisely
> > > what the chip does ...
> > >
> > [Bala]: i am seeing command timeout after injecting cc event after
> > read
> > version request.
> >
> > > > The reason for no timeouts error, we are injecting an command
> > > > complete
> > > > after last packet sent out, so this injection helps
> > > > .bin file to speed out it download part, so as the bin is dumped
> > > > fastly we send an HCI RESET Comamnd where we recevie an command
> > > > complete
> > > > event
> > > > with non zero opcode which is cancelling the command timeout
> > > > timer.
> > > >
> > > > when we inject command complete event, in short we are
> > > > completing
> > > > setup process in less than 2 seconds(command timeout timer value),
> > > > so before 2 seconds we are sending an HCI RESET command whose
> > > > command
> > > > complete event opcode value is an non zero (which cancels the command
> > > > timeout timer)
> > >
> > > I agree that HCI_RESET cancels the command timeout timer if it is sent
> > > before the 2s timout expires, but I have doubts on the part about
> > > command complete events.
> > >
> > > In my observations there are no command timeouts if a command complete
> > > (with opcode != HCI_OP_NOP) is injected after the firmware download,
> > > even if a 3s sleep is added before sending the HCI_RESET.
> > >
> >
> > [Bala]: add sleep before sending HCI reset, oxfc00 timeout observed.
>
> Please double check your setup. Are you 100% sure you are not still
> sending HCI_OP_NOP as opcode?
>
[Bala]: sorry i am injecting the HCI_OP_NOP, so that is the reason we
have
an timeouts.
yes if the opcode 0x42 injected, no timeouts are observed.
