Hi Johan,
On 2019-01-09 20:08, Johan Hovold wrote:
> On Fri, Dec 21, 2018 at 05:59:47PM -0800, Matthias Kaehlcke wrote:
> > On Thu, Dec 20, 2018 at 08:16:35PM +0530, Balakrishna Godavarthi
> > wrote:
> > > wcn3990 requires a power pulse to turn ON/OFF along with
> > > regulators. Sometimes we are observing the power pulses are sent
> > > out with some time delay, due to queuing these commands. This is
> > > causing synchronization issues with chip, which intern delay the
> > > chip setup or may end up with communication issues.
> > >
> > > Signed-off-by: Balakrishna Godavarthi <bgodavar@xxxxxxxxxxxxxx>
> > > ---
> > > drivers/bluetooth/hci_qca.c | 38 ++++++++++++++-----------------------
> > > 1 file changed, 14 insertions(+), 24 deletions(-)
> > >
> > > diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
> > > index f036c8f98ea3..5a07c2370289 100644
> > > --- a/drivers/bluetooth/hci_qca.c
> > > +++ b/drivers/bluetooth/hci_qca.c
> > > @@ -1013,11 +1013,9 @@ static inline void host_set_baudrate(struct hci_uart *hu, unsigned int speed)
> > > hci_uart_set_baudrate(hu, speed);
> > > }
> > >
> > > -static int qca_send_power_pulse(struct hci_dev *hdev, u8 cmd)
> > > +static int qca_send_power_pulse(struct hci_uart *hu, u8 cmd)
> > > {
> > > - struct hci_uart *hu = hci_get_drvdata(hdev);
> > > - struct qca_data *qca = hu->priv;
> > > - struct sk_buff *skb;
> > > + int ret;
> > >
> > > /* These power pulses are single byte command which are sent
> > > * at required baudrate to wcn3990. On wcn3990, we have an external
> > > @@ -1029,19 +1027,16 @@ static int qca_send_power_pulse(struct hci_dev *hdev, u8 cmd)
> > > * save power. Disabling hardware flow control is mandatory while
> > > * sending power pulses to SoC.
> > > */
> > > - bt_dev_dbg(hdev, "sending power pulse %02x to SoC", cmd);
> > > -
> > > - skb = bt_skb_alloc(sizeof(cmd), GFP_KERNEL);
> > > - if (!skb)
> > > - return -ENOMEM;
> > > -
> > > + bt_dev_dbg(hu->hdev, "sending power pulse %02x to SoC", cmd);
> > > hci_uart_set_flow_control(hu, true);
> > > + ret = serdev_device_write_buf(hu->serdev, &cmd, sizeof(cmd));
> > > + if (ret < 0) {
> > > + bt_dev_err(hu->hdev, "failed to send power pulse %02x to SoC",
> > > + cmd);
> > > + return ret;
> > > + }
> > >
> > > - skb_put_u8(skb, cmd);
> > > - hci_skb_pkt_type(skb) = HCI_COMMAND_PKT;
> > > -
> > > - skb_queue_tail(&qca->txq, skb);
> > > - hci_uart_tx_wakeup(hu);
> > > + serdev_device_wait_until_sent(hu->serdev, 0);
>
> Again, do you really want to wait indefinitely here?
>
[Bala]: these commands are mandatory to turn ON or OFF the chip.
so blocking to the max time is required.
these commands are sent during the BT chip ON & OFF.
in the latest series, i have flushed the uart before sending
this
commands
so the uart FIFO(as just opened the port before calling this
function) or the circular
buffer will be empty and also i am disabling the flow control
too.
https://patchwork.kernel.org/patch/10744435/
