On Wed, Jul 18, 2018 at 09:03:08PM +0530, Balakrishna Godavarthi wrote:
> Hi Matthias,
>
> On 2018-07-16 21:35, Matthias Kaehlcke wrote:
> > On Mon, Jul 16, 2018 at 07:21:56PM +0530, Balakrishna Godavarthi wrote:
> > > Hi Matthias,
> > >
> > > On 2018-07-07 03:51, Matthias Kaehlcke wrote:
> > > > On Thu, Jul 05, 2018 at 10:25:15PM +0530, Balakrishna Godavarthi wrote:
> > > > > Add support to set voltage/current of various regulators
> > > > > to power up/down Bluetooth chip wcn3990.
> > > > >
> > > > > Signed-off-by: Balakrishna Godavarthi <bgodavar@xxxxxxxxxxxxxx>
> > > > > ---
> > > > > changes in v9:
> > > > > * moved flow control to vendor and set_baudarte functions.
> > > > > * removed parent regs.
> > > > >
> > > > > changes in v8:
> > > > > * closing qca buffer, if qca_power_setup fails
> > > > > * chnaged ibs start timer function call location.
> > > > > * updated review comments.
> > > > >
> > > > > changes in v7:
> > > > > * addressed review comments.
> > > > >
> > > > > changes in v6:
> > > > > * Hooked up qca_power to qca_serdev.
> > > > > * renamed all the naming inconsistency functions with qca_*
> > > > > * leveraged common code of ROME for wcn3990.
> > > > > * created wrapper functions for re-usable blocks.
> > > > > * updated function of _*regulator_enable and _*regualtor_disable.
> > > > > * removed redundant comments and functions.
> > > > > * addressed review comments.
> > > > >
> > > > > Changes in v5:
> > > > > * updated regulator vddpa min_uV to 1304000.
> > > > > * addressed review comments.
> > > > >
> > > > > Changes in v4:
> > > > > * Segregated the changes of btqca from hci_qca
> > > > > * rebased all changes on top of bluetooth-next.
> > > > > * addressed review comments.
> > > > >
> > > > > ---
> > > > > drivers/bluetooth/btqca.h | 3 +
> > > > > drivers/bluetooth/hci_qca.c | 387
> > > > > +++++++++++++++++++++++++++++++-----
> > > > > 2 files changed, 345 insertions(+), 45 deletions(-)
> > > > >
> > > > > diff --git a/drivers/bluetooth/btqca.h b/drivers/bluetooth/btqca.h
> > > > > index a9c2779f3e07..0c01f375fe83 100644
> > > > > --- a/drivers/bluetooth/btqca.h
> > > > > +++ b/drivers/bluetooth/btqca.h
> > > > > @@ -37,6 +37,9 @@
> > > > > #define EDL_TAG_ID_HCI (17)
> > > > > #define EDL_TAG_ID_DEEP_SLEEP (27)
> > > > >
> > > > > +#define QCA_WCN3990_POWERON_PULSE 0xFC
> > > > > +#define QCA_WCN3990_POWEROFF_PULSE 0xC0
> > > > > +
> > > > > enum qca_bardrate {
> > > > > QCA_BAUDRATE_115200 = 0,
> > > > > QCA_BAUDRATE_57600,
> > > > > diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
> > > > > index 7ebfaa0edf3f..d62c7785a618 100644
> > > > > --- a/drivers/bluetooth/hci_qca.c
> > > > > +++ b/drivers/bluetooth/hci_qca.c
> > > > > @@ -5,7 +5,7 @@
> > > > > * protocol extension to H4.
> > > > > *
> > > > > * Copyright (C) 2007 Texas Instruments, Inc.
> > > > > - * Copyright (c) 2010, 2012 The Linux Foundation. All rights
> > > > > reserved.
> > > > > + * Copyright (c) 2010, 2012, 2018 The Linux Foundation. All rights
> > > > > reserved.
> > > > > *
> > > > > * Acknowledgements:
> > > > > * This file is based on hci_ll.c, which was...
> > > > > @@ -31,9 +31,14 @@
> > > > > #include <linux/kernel.h>
> > > > > #include <linux/clk.h>
> > > > > #include <linux/debugfs.h>
> > > > > +#include <linux/delay.h>
> > > > > +#include <linux/device.h>
> > > > > #include <linux/gpio/consumer.h>
> > > > > #include <linux/mod_devicetable.h>
> > > > > #include <linux/module.h>
> > > > > +#include <linux/of_device.h>
> > > > > +#include <linux/platform_device.h>
> > > > > +#include <linux/regulator/consumer.h>
> > > > > #include <linux/serdev.h>
> > > > >
> > > > > #include <net/bluetooth/bluetooth.h>
> > > > > @@ -124,12 +129,46 @@ enum qca_speed_type {
> > > > > QCA_OPER_SPEED
> > > > > };
> > > > >
> > > > > +/*
> > > > > + * Voltage regulator information required for configuring the
> > > > > + * QCA Bluetooth chipset
> > > > > + */
> > > > > +struct qca_vreg {
> > > > > + const char *name;
> > > > > + unsigned int min_uV;
> > > > > + unsigned int max_uV;
> > > > > + unsigned int load_uA;
> > > > > +};
> > > > > +
> > > > > +struct qca_vreg_data {
> > > > > + enum qca_btsoc_type soc_type;
> > > > > + struct qca_vreg *vregs;
> > > > > + size_t num_vregs;
> > > > > +};
> > > > > +
> > > > > +/*
> > > > > + * Platform data for the QCA Bluetooth power driver.
> > > > > + */
> > > > > +struct qca_power {
> > > > > + struct device *dev;
> > > > > + const struct qca_vreg_data *vreg_data;
> > > > > + struct regulator_bulk_data *vreg_bulk;
> > > > > + bool vregs_on;
> > > > > +};
> > > > > +
> > > > > struct qca_serdev {
> > > > > struct hci_uart serdev_hu;
> > > > > struct gpio_desc *bt_en;
> > > > > struct clk *susclk;
> > > > > + enum qca_btsoc_type btsoc_type;
> > > > > + struct qca_power *bt_power;
> > > > > + u32 init_speed;
> > > > > + u32 oper_speed;
> > > > > };
> > > > >
> > > > > +static int qca_power_setup(struct hci_uart *hu, bool on);
> > > > > +static void qca_power_shutdown(struct hci_uart *hu);
> > > > > +
> > > > > static void __serial_clock_on(struct tty_struct *tty)
> > > > > {
> > > > > /* TODO: Some chipset requires to enable UART clock on client
> > > > > @@ -407,6 +446,7 @@ static int qca_open(struct hci_uart *hu)
> > > > > {
> > > > > struct qca_serdev *qcadev;
> > > > > struct qca_data *qca;
> > > > > + int ret;
> > > > >
> > > > > BT_DBG("hu %p qca_open", hu);
> > > > >
> > > > > @@ -458,19 +498,32 @@ static int qca_open(struct hci_uart *hu)
> > > > >
> > > > > hu->priv = qca;
> > > > >
> > > > > - timer_setup(&qca->wake_retrans_timer,
> > > > > hci_ibs_wake_retrans_timeout, 0);
> > > > > - qca->wake_retrans = IBS_WAKE_RETRANS_TIMEOUT_MS;
> > > > > -
> > > > > - timer_setup(&qca->tx_idle_timer, hci_ibs_tx_idle_timeout, 0);
> > > > > - qca->tx_idle_delay = IBS_TX_IDLE_TIMEOUT_MS;
> > > > > -
> > > > > if (hu->serdev) {
> > > > > serdev_device_open(hu->serdev);
> > > > >
> > > > > qcadev = serdev_device_get_drvdata(hu->serdev);
> > > > > - gpiod_set_value_cansleep(qcadev->bt_en, 1);
> > > > > + if (qcadev->btsoc_type != QCA_WCN3990) {
> > > > > + gpiod_set_value_cansleep(qcadev->bt_en, 1);
> > > > > + } else {
> > > > > + hu->init_speed = qcadev->init_speed;
> > > > > + hu->oper_speed = qcadev->oper_speed;
> > > > > + ret = qca_power_setup(hu, true);
> > > > > + if (ret) {
> > > > > + destroy_workqueue(qca->workqueue);
> > > > > + kfree_skb(qca->rx_skb);
> > > > > + hu->priv = NULL;
> > > > > + kfree(qca);
> > > > > + return ret;
> > > > > + }
> > > > > + }
> > > > > }
> > > > >
> > > > > + timer_setup(&qca->wake_retrans_timer,
> > > > > hci_ibs_wake_retrans_timeout, 0);
> > > > > + qca->wake_retrans = IBS_WAKE_RETRANS_TIMEOUT_MS;
> > > > > +
> > > > > + timer_setup(&qca->tx_idle_timer, hci_ibs_tx_idle_timeout, 0);
> > > > > + qca->tx_idle_delay = IBS_TX_IDLE_TIMEOUT_MS;
> > > > > +
> > > > > BT_DBG("HCI_UART_QCA open, tx_idle_delay=%u, wake_retrans=%u",
> > > > > qca->tx_idle_delay, qca->wake_retrans);
> > > > >
> > > > > @@ -554,10 +607,13 @@ static int qca_close(struct hci_uart *hu)
> > > > > qca->hu = NULL;
> > > > >
> > > > > if (hu->serdev) {
> > > > > - serdev_device_close(hu->serdev);
> > > > > -
> > > > > qcadev = serdev_device_get_drvdata(hu->serdev);
> > > > > - gpiod_set_value_cansleep(qcadev->bt_en, 0);
> > > > > + if (qcadev->btsoc_type == QCA_WCN3990)
> > > > > + qca_power_shutdown(hu);
> > > > > + else
> > > > > + gpiod_set_value_cansleep(qcadev->bt_en, 0);
> > > > > +
> > > > > + serdev_device_close(hu->serdev);
> > > > > }
> > > > >
> > > > > kfree_skb(qca->rx_skb);
> > > > > @@ -891,6 +947,7 @@ static int qca_set_baudrate(struct hci_dev
> > > > > *hdev, uint8_t baudrate)
> > > > > struct hci_uart *hu = hci_get_drvdata(hdev);
> > > > > struct qca_data *qca = hu->priv;
> > > > > struct sk_buff *skb;
> > > > > + struct qca_serdev *qcadev;
> > > > > u8 cmd[] = { 0x01, 0x48, 0xFC, 0x01, 0x00 };
> > > > >
> > > > > if (baudrate > QCA_BAUDRATE_3200000)
> > > > > @@ -904,6 +961,13 @@ static int qca_set_baudrate(struct hci_dev
> > > > > *hdev, uint8_t baudrate)
> > > > > return -ENOMEM;
> > > > > }
> > > > >
> > > > > + /* Disabling hardware flow control is mandate while
> > > >
> > > > nit: s/mandate/mandatory|required/
> > > >
> > > > > + * sending change baudrate request to wcn3990 SoC.
> > > > > + */
> > > > > + qcadev = serdev_device_get_drvdata(hu->serdev);
> > > > > + if (qcadev->btsoc_type == QCA_WCN3990)
> > > > > + hci_uart_set_flow_control(hu, true);
> > > > > +
> > > > > /* Assign commands to change baudrate and packet type. */
> > > > > skb_put_data(skb, cmd, sizeof(cmd));
> > > > > hci_skb_pkt_type(skb) = HCI_COMMAND_PKT;
> > > > > @@ -919,6 +983,9 @@ static int qca_set_baudrate(struct hci_dev
> > > > > *hdev, uint8_t baudrate)
> > > > > schedule_timeout(msecs_to_jiffies(BAUDRATE_SETTLE_TIMEOUT_MS));
> > > > > set_current_state(TASK_RUNNING);
> > > > >
> > > > > + if (qcadev->btsoc_type == QCA_WCN3990)
> > > > > + hci_uart_set_flow_control(hu, false);
> > > > > +
> > > > > return 0;
> > > > > }
> > > > >
> > > > > @@ -930,6 +997,36 @@ static inline void host_set_baudrate(struct
> > > > > hci_uart *hu, unsigned int speed)
> > > > > hci_uart_set_baudrate(hu, speed);
> > > > > }
> > > > >
> > > > > +static int qca_send_vendor_cmd(struct hci_dev *hdev, u8 cmd)
> > > > > +{
> > > > > + struct hci_uart *hu = hci_get_drvdata(hdev);
> > > > > + struct qca_data *qca = hu->priv;
> > > > > + struct sk_buff *skb;
> > > > > +
> > > > > + bt_dev_dbg(hdev, "sending command %02x to SoC", cmd);
> > > > > +
> > > > > + skb = bt_skb_alloc(sizeof(cmd), GFP_KERNEL);
> > > > > + if (!skb)
> > > > > + return -ENOMEM;
> > > > > +
> > > > > + /* Disabling hardware flow control is mandate while
> > > >
> > > > Same nit as above
> > > >
> > > > > + * sending vendor power on and off pulse to SoC.
> > > > > + */
> > > >
> > > > The function is called qca_send_vendor_cmd(), the comment about power
> > > > on/off pulses seems misplaced here. Are there other 'vendor commands'
> > > > that require a different flow control behavior?
> > > >
> > > > Perhaps the function should have a different name or we need another
> > > > wrapper.
> > > >
> > > > > + hci_uart_set_flow_control(hu, true);
> > > >
> > > > Should the changing of the flow control be limited to wcn3990? As of
> > > > now the function is only called for wcn3990, however this is not
> > > > stated as a requirement and might change in the future.
> > > >
> > > > > + skb_put_u8(skb, cmd);
> > > > > + hci_skb_pkt_type(skb) = HCI_COMMAND_PKT;
> > > > > +
> > > > > + skb_queue_tail(&qca->txq, skb);
> > > > > + hci_uart_tx_wakeup(hu);
> > > > > +
> > > > > + /* Wait for 100 uS for SoC to settle down */
> > > > > + usleep_range(100, 200);
> > > >
> > > > Is this needed for any 'vendor command' or directly related with the
> > > > power on/off pulses?
> > > >
> > > > > + hci_uart_set_flow_control(hu, false);
> > > > > +
> > > > > + return 0;
> > > > > +}
> > > > > +
> > > > > static unsigned int qca_get_speed(struct hci_uart *hu,
> > > > > enum qca_speed_type speed_type)
> > > > > {
> > > > > @@ -952,10 +1049,19 @@ static unsigned int qca_get_speed(struct
> > > > > hci_uart *hu,
> > > > >
> > > > > static int qca_check_speeds(struct hci_uart *hu)
> > > > > {
> > > > > - /* One or the other speeds should be non zero. */
> > > > > - if (!qca_get_speed(hu, QCA_INIT_SPEED) &&
> > > > > - !qca_get_speed(hu, QCA_OPER_SPEED))
> > > > > + struct qca_serdev *qcadev;
> > > > > +
> > > > > + qcadev = serdev_device_get_drvdata(hu->serdev);
> > > > > + if ((qcadev->btsoc_type == QCA_WCN3990 &&
> > > > > + !qca_get_speed(hu, QCA_INIT_SPEED)) ||
> > > > > + !qca_get_speed(hu, QCA_OPER_SPEED)) {
> > > > > + /* Both INIT and OPER speed should be non zero. */
> > > > > return -EINVAL;
> > > > > + } else if (!qca_get_speed(hu, QCA_INIT_SPEED) &&
> > > > > + !qca_get_speed(hu, QCA_OPER_SPEED)) {
> > > > > + /* One or the other speeds should be non zero. */
> > > > > + return -EINVAL;
> > > > > + }
> > > >
> > > > It is questionable if the comments are useful, they are basically
> > > > stating the same as the conditions.
> > > >
> > > > if-else statements with a single statement in all branches shouldn't
> > > > use curly braces. Personally I don't dislike them in this case with
> > > > the multi-line conditions, but in principle they shoulnd't be there.
> > > >
> > > > nit: this would be easier to read with nested if statements:
> > > >
> > > > if (qcadev->btsoc_type == QCA_WCN3990)
> > > > if (!qca_get_speed(hu, QCA_INIT_SPEED)) ||
> > > > !qca_get_speed(hu, QCA_OPER_SPEED))
> > > > return -EINVAL;
> > > > else
> > > > if (!qca_get_speed(hu, QCA_INIT_SPEED) &&
> > > > !qca_get_speed(hu, QCA_OPER_SPEED)) {
> > > > return -EINVAL;
> > > >
> > > > > return 0;
> > > > > }
> > > > > @@ -986,15 +1092,40 @@ static int qca_set_speed(struct hci_uart *hu,
> > > > > enum qca_speed_type speed_type)
> > > > > return 0;
> > > > > }
> > > > >
> > > > > +static int qca_wcn3990_init(struct hci_uart *hu)
> > > > > +{
> > > > > + int ret;
> > > > > +
> > > > > + ret = qca_send_vendor_cmd(hu->hdev, QCA_WCN3990_POWERON_PULSE);
> > > > > + if (ret)
> > > > > + return ret;
> > > > > +
> > > > > + /* Wait for 100 ms for SoC to boot up */
> > > > > + msleep(100);
> > > > > + serdev_device_close(hu->serdev);
> > > > > + ret = serdev_device_open(hu->serdev);
> > > > > + if (ret) {
> > > > > + bt_dev_err(hu->hdev, "failed to open port");
> > > > > + return ret;
> > > > > + }
> > > > > +
> > > > > + /* Setup initial baudrate */
> > > > > + qca_set_speed(hu, QCA_INIT_SPEED);
> > > >
> > > > The comment is a bit redundant.
> > > >
> > > > > + hci_uart_set_flow_control(hu, false);
> > > > > +
> > > > > + return 0;
> > > > > +}
> > > > > +
> > > > > static int qca_setup(struct hci_uart *hu)
> > > > > {
> > > > > struct hci_dev *hdev = hu->hdev;
> > > > > struct qca_data *qca = hu->priv;
> > > > > unsigned int speed, qca_baudrate = QCA_BAUDRATE_115200;
> > > > > + struct qca_serdev *qcadev;
> > > > > int ret;
> > > > > int soc_ver = 0;
> > > > >
> > > > > - bt_dev_info(hdev, "ROME setup");
> > > > > + qcadev = serdev_device_get_drvdata(hu->serdev);
> > > > >
> > > > > ret = qca_check_speeds(hu);
> > > > > if (ret)
> > > > > @@ -1006,6 +1137,21 @@ static int qca_setup(struct hci_uart *hu)
> > > > > /* Setup initial baudrate */
> > > > > qca_set_speed(hu, QCA_INIT_SPEED);
> > > > >
> > > > > + if (qcadev->btsoc_type == QCA_WCN3990) {
> > > > > + bt_dev_dbg(hdev, "setting up wcn3990");
> > > >
> > > > Seems like this should be bt_dev_info() for consistency with Rome.
> > > >
> > > > > + ret = qca_wcn3990_init(hu);
> > > > > + if (ret)
> > > > > + return ret;
> > > > > +
> > > > > + ret = qca_read_soc_version(hdev, &soc_ver);
> > > > > + if (ret < 0 || soc_ver == 0) {
> > > > > + bt_dev_err(hdev, "Failed to get version %d", ret);
> > > > > + return ret;
> > > > > + }
> > > > > + } else {
> > > > > + bt_dev_info(hdev, "ROME setup");
> > > > > + }
> > > > > +
> > > > > /* Setup user speed if needed */
> > > > > speed = qca_get_speed(hu, QCA_OPER_SPEED);
> > > > > if (speed) {
> > > > > @@ -1016,16 +1162,18 @@ static int qca_setup(struct hci_uart *hu)
> > > > > qca_baudrate = qca_get_baudrate_value(speed);
> > > > > }
> > > > >
> > > > > - /* Get QCA version information */
> > > > > - ret = qca_read_soc_version(hdev, &soc_ver);
> > > > > - if (ret < 0 || soc_ver == 0) {
> > > > > - bt_dev_err(hdev, "QCA Failed to get version (%d)", ret);
> > > > > - return ret;
> > > > > + if (!soc_ver) {
> > > >
> > > >
> > > > The following would probably be clearer:
> > > >
> > > > if (qcadev->btsoc_type != QCA_WCN3990) {
> > > >
> > > > > + /* Get QCA version information */
> > > > > + ret = qca_read_soc_version(hdev, &soc_ver);
> > > > > + if (ret < 0 || soc_ver == 0) {
> > > > > + bt_dev_err(hdev, "QCA Failed to get version (%d)", ret);
> > > > > + return ret;
> > > > > + }
> > > > > + bt_dev_info(hdev, "QCA controller version 0x%08x", soc_ver);
> > > >
> > > > Couldn't we hide some of this in qca_read_soc_version()?
> > > >
> > > > qca_read_soc_version() could at least do the logging in the error case
> > > > (the 'soc_ver == 0' case could be handled there as well), which would
> > > > leave us with:
> > > >
> > > >
> > > > ret = qca_read_soc_version(hdev, &soc_ver);
> > > > if (ret)
> > > > return ret;
> > > >
> > > > And the same above.
> > > >
> > > > The controller version can be logged outside of the branch for both
> > > > wcn3990 and Rome.
> > > >
> > > > > }
> > > > > - bt_dev_info(hdev, "QCA controller version 0x%08x", soc_ver);
> > > > >
> > > > > /* Setup patch / NVM configurations */
> > > > > - ret = qca_uart_setup(hdev, qca_baudrate, QCA_ROME, soc_ver);
> > > > > + ret = qca_uart_setup(hdev, qca_baudrate, qcadev->btsoc_type,
> > > > > soc_ver);
> > > > > if (!ret) {
> > > > > set_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags);
> > > > > qca_debugfs_init(hdev);
> > > > > @@ -1061,9 +1209,123 @@ static struct hci_uart_proto qca_proto = {
> > > > > .dequeue = qca_dequeue,
> > > > > };
> > > > >
> > > > > +static const struct qca_vreg_data qca_soc_data = {
> > > > > + .soc_type = QCA_WCN3990,
> > > > > + .vregs = (struct qca_vreg []) {
> > > > > + { "vddio", 1800000, 1800000, 0 },
> > > > > + { "vddxo", 1800000, 1800000, 1 },
> > > > > + { "vddrf", 1304000, 1304000, 1 },
> > > > > + { "vddch0", 3000000, 3312000, 1 },
> > > > > + },
> > > > > + .num_vregs = 4,
> > > > > +};
> > > >
> > > > I didn't chime in earlier in the discussion with Stephen on the
> > > > regulators (https://patchwork.kernel.org/patch/10467911/), however I
> > > > agree with him that specifying at load of 1uA doesn't seem to make
> > > > much sense. What would happen if the load remained unspecified (or 0)?
> > >
> > > [Bala]: On RPMh based designs, calling a regulator_set_load with a
> > > non-zero
> > > value moves the regulator to NPM (high power mode) which is required
> > > for BT
> > > communication.
> > > and call with 0uA moves it to low-power-mode (vote from
> > > APPS).
> > > Basically whenever BT wants these in NPM it calls set-load with 1.
> >
> > This assumes that the chip is powered by RPMh regulators, which
> > depending on the system may or may not be true. On systems with other
> > regulators you are telling the regulator that the max load is 1uA, and
> > the regulator might comply, going in a low power mode that does not
> > provide enough current for the chip to operate properly.
> >
> > Doesn't the datasheet of the chip specify actual max currents for
> > these consumers that could be used instead of the bogus 1uA? If not
> > you could ask the designers of the chip for an approximate number
> > (preferably erring on the upper side).
>
> [Bala]: yes your true, now current values are aligned according to the RPMH
> regs packages.
> this is not our goal. what ever the package we use wcn3990 should be
> platform independent.
> I propose an idea that, we will have default current value in driver
> i.e current required by regs to turn on wcn3990 and also we will provide
> interface in driver
> to read current from dts tree.
>
> i.e. if we have prop for current to the reg in the dts, we will read
> the value assigned to prop else we will take default current
>
> <code snippets>
>
> qca->vreg_data->vregs[i].name = current; // holds the default current
I suppose this should be 'qca->vreg_data->vregs[i].load_uA'
> value taken from data provided from deb. this will value remains unchanged.
> if (device_property_read_bool(dev, prop_name)) // if we have prop
> name enabled then read the value.
> device_property_read_u32(dev, prop_name, &vregs->load_uA);
It's still not clear why this would be needed. Is 1uA a magic value
that is somehow used by RPMh regulators?
Earlier you said:
> > > [Bala]: On RPMh based designs, calling a regulator_set_load with a
> > > non-zero
> > > value moves the regulator to NPM (high power mode) which is required
> > > for BT
> > > communication.
> > > and call with 0uA moves it to low-power-mode (vote from
> > > APPS).
> > > Basically whenever BT wants these in NPM it calls set-load with 1.
This is the ->set_load function of the RPMh regulator:
static int rpmh_regulator_vrm_set_load(struct regulator_dev *rdev, int load_uA)
{
struct rpmh_vreg *vreg = rdev_get_drvdata(rdev);
unsigned int mode;
if (load_uA >= vreg->hw_data->hpm_min_load_uA)
mode = REGULATOR_MODE_NORMAL;
else
mode = REGULATOR_MODE_IDLE;
return rpmh_regulator_vrm_set_mode(rdev, mode);
}
and REGULATOR_MODE_NORMAL translates to HPM for PMIC4 LDOs:
static const int pmic_mode_map_pmic4_ldo[REGULATOR_MODE_STANDBY + 1] = {
[REGULATOR_MODE_INVALID] = -EINVAL,
[REGULATOR_MODE_STANDBY] = PMIC4_LDO_MODE_RETENTION,
[REGULATOR_MODE_IDLE] = PMIC4_LDO_MODE_LPM,
[REGULATOR_MODE_NORMAL] = PMIC4_LDO_MODE_HPM,
[REGULATOR_MODE_FAST] = -EINVAL,
};
https://patchwork.kernel.org/patch/10524299/
I don't see how a load value of 1uA would cause the regulator to enter
HPM and another higher value wouldn't. HPM is entered as long as
'load_uA >= vreg->hw_data->hpm_min_load_uA', or am I missing
something here?
--
To unsubscribe from this list: send the line "unsubscribe linux-bluetooth" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
