Re: [PATCH] Bluetooth: hci_bcm: Configure SCO routing automatically

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Rob,

>>>> Added support to automatically configure the SCO packet routing at the
>>>> device setup. The SCO packets are used with the HSP / HFP profiles, but in
>>>> some devices (ex. CYW43438) they are routed to a PCM output by default. This
>>>> change allows sending the vendor specific HCI command to configure the SCO
>>>> routing. The parameters of the command are loaded from the device tree.
>>> 
>>> Please wrap your commit msg.
>> 
>> 
>> Sure.
>>> 
>>> 
>>>> 
>>>> Signed-off-by: Attila Tőkés <attitokes@xxxxxxxxx>
>>>> ---
>>>> .../bindings/net/broadcom-bluetooth.txt       |  7 ++
>>> 
>>> Please split bindings to separate patch.
>> 
>> 
>> Ok, I will split this in two.
>>> 
>>> 
>>> 
>>> 
>>>> drivers/bluetooth/hci_bcm.c                   | 72 +++++++++++++++++++
>>>> 2 files changed, 79 insertions(+)
>>>> 
>>>> diff --git
>>>> a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
>>>> b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
>>>> index 4194ff7e..aea3a094 100644
>>>> --- a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
>>>> +++ b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
>>>> @@ -21,6 +21,12 @@ Optional properties:
>>>>  - clocks: clock specifier if external clock provided to the controller
>>>>  - clock-names: should be "extclk"
>>>> 
>>>> + SCO routing parameters:
>>>> + - sco-routing: 0-3 (PCM, Transport, Codec, I2S)
>>>> + - pcm-interface-rate: 0-4 (128 Kbps - 2048 Kbps)
>>>> + - pcm-frame-type: 0 (short), 1 (long)
>>>> + - pcm-sync-mode: 0 (slave), 1 (master)
>>>> + - pcm-clock-mode: 0 (slave), 1 (master)
>>> 
>>> Are these Broadcom specific? Properties need either vendor prefix or
>>> to be documented in a common location. I think these look like the
>>> latter.
>> 
>> 
>> These will be used as parameters of a vendor specific (Broadcom/Cypress)
>> command configuring the SCO packet routing. See the Write_SCO_PCM_Int_Param
>> command from: http://www.cypress.com/file/298311/download.
> 
> The DT should just describe how the h/w is hooked-up. What the s/w has
> to do based on that is the driver's problem which is certainly
> vendor/chip specific, but that is all irrelevant to the binding.
> 
>> What would be the property names with a Broadcom / Cypress vendor prefix?
>> 
>>    brcm,sco-routing
>>    brcm,pcm-interface-rate
>>    brcm,pcm-frame-type
>>    brcm,pcm-sync-mode
>>    brcm,pcm-clock-mode
>> 
>> ?
> 
> Yes.

we can do this. However all pcm-* are optional if you switch the HCI transport. And sco-routing should default to HCI if that is not present. Meaning a driver should actively trying to change this. Nevertheless, it would be good if a driver reads the current settings.

In theory we could make sco-routing generic, but so many vendors have different modes, that we better keep this vendor specific.

Regards

Marcel

--
To unsubscribe from this list: send the line "unsubscribe linux-bluetooth" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Bluez Devel]     [Linux Wireless Networking]     [Linux Wireless Personal Area Networking]     [Linux ATH6KL]     [Linux USB Devel]     [Linux Media Drivers]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Big List of Linux Books]

  Powered by Linux