Re: [v5 PATCH 2/3] doc/mgmt-api: Add support for Set Phy Configuration command

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Jaganath,

On 02/28/2018 04:49 PM, Jaganath Kanakkassery wrote:
> This also adds PHY Configuration Changed Event.
> ---
>  doc/mgmt-api.txt | 52 ++++++++++++++++++++++++++++++++++++++++++++++++++++
>  1 file changed, 52 insertions(+)
> 
> diff --git a/doc/mgmt-api.txt b/doc/mgmt-api.txt
> index c07c48c..628ff18 100644
> --- a/doc/mgmt-api.txt
> +++ b/doc/mgmt-api.txt
> @@ -2940,9 +2940,46 @@ Get PHY Configuration Command
>  	LE 1M TX and LE 1M RX would be supported by default.
>  
>  	This command is only available for LE capable controllers.
> +        It will return Not Supported otherwise.
> +
> +        Possible errors:        Not Supported

nitpick: better to use tab instead of whitespaces


> +				Invalid Index
> +
> +Set PHY Configuration Command
> +=============================
> +
> +	Command Code:		0x0044
> +	Controller Index:	<controller id>
> +	Command Parameters: 	Default_phys (2 Octet)
> +	Return Parameters:
> +
> +	This command is used to set the default phy to the controller.
> +
> +	This will be stored and used for all the subsequent scanning
> +	and connection initiation.
> +
> +	The list of supported PHYs can be retrieved via the
> +	Get PHY Configuration command. Selecting unsupported PHYs will
> +	result in an Invalid Parameters	error.
> +
> +	This can be called at any point to change the preferred PHYs.
> +
> +	Default_phy is a bitmask with the following bits.

s/Default_phy/Default_phys/


Regards,
Eramoto


> +		0	LE 1M TX
> +		1	LE 1M RX
> +		2	LE 2M TX
> +		3	LE 2M RX
> +		4	LE CODED TX
> +		5	LE CODED RX
> +
> +	This command generates a Command Complete event on success
> +	or a Command Status event on failure.
> +
> +	This command is only available for LE capable controllers.
>  	It will return Not Supported otherwise.
>  
>  	Possible errors:	Not Supported
> +				Invalid Parameters
>  				Invalid Index
>  
>  Command Complete Event
> @@ -3810,3 +3847,18 @@ Extended Controller Information Changed Event
>  
>  	The event will only be sent to management sockets other than the
>  	one through which the change was triggered.
> +
> +PHY Configuration Changed Event
> +===============================
> +
> +	Event Code:		0x0026
> +	Controller Index:	<controller id>
> +	Event Parameters:	Selected_phys (2 Octets)
> +
> +	This event indicates that default PHYs have been updated.
> +
> +	This event will only be used after Set PHY Configuration
> +	command has been used at least once.
> +
> +	The event will only be sent to management sockets other than the
> +	one through which the change was triggered.
> 

--
To unsubscribe from this list: send the line "unsubscribe linux-bluetooth" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Bluez Devel]     [Linux Wireless Networking]     [Linux Wireless Personal Area Networking]     [Linux ATH6KL]     [Linux USB Devel]     [Linux Media Drivers]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Big List of Linux Books]

  Powered by Linux