On Tue, Sep 19, 2017 at 10:44 AM, Marcel Holtmann <marcel@xxxxxxxxxxxx> wrote: > Hi Peter, > >>>>> the latest Fedora 27 kernel which has all the RPi3 patches applied doesn’t actually work. It provides this backlog. >>>>> >>>>> [ 229.162921] CPU: 1 PID: 582 Comm: kworker/u9:1 Not tainted 4.13.2-300.fc27.armv7hl #1 >>>>> [ 229.171285] Hardware name: Generic DT based system >>>>> [ 229.176774] Workqueue: hci0 hci_cmd_work [bluetooth] >>>>> [ 229.176774] Workqueue: hci0 hci_cmd_work [bluetooth] >>>>> [ 229.182117] [<c0312af4>] (unwind_backtrace) from [<c030d264>] (show_stack+0x18/0x1c) >>>>> [ 229.190374] [<c030d264>] (show_stack) from [<c0b66174>] (dump_stack+0xa0/0xd8) >>>>> [ 229.198122] [<c0b66174>] (dump_stack) from [<c03aeaec>] (register_lock_class+0x298/0x514) >>>>> [ 229.206835] [<c03aeaec>] (register_lock_class) from [<c03b1f9c>] (__lock_acquire+0xe4/0x1608) >>>>> [ 229.215952] [<c03b1f9c>] (__lock_acquire) from [<c03b3fd0>] (lock_acquire+0x280/0x2dc) >>>>> [ 229.224386] [<c03b3fd0>] (lock_acquire) from [<c0b80ba4>] (_raw_read_lock+0x4c/0x5c) >>>>> [ 229.232740] [<c0b80ba4>] (_raw_read_lock) from [<bf47903c>] (hci_uart_tx_wakeup+0x1c/0x98 [hci_uart]) >>>>> [ 229.242725] [<bf47903c>] (hci_uart_tx_wakeup [hci_uart]) from [<bf47a0e0>] (hci_uart_send_frame+0x54/0x6c [hci_uart]) >>>>> [ 229.254485] [<bf47a0e0>] (hci_uart_send_frame [hci_uart]) from [<bf3cb260>] (hci_send_frame+0xc8/0xf4 [bluetooth]) >>>>> [ 229.266157] [<bf3cb260>] (hci_send_frame [bluetooth]) from [<bf3cb334>] (hci_cmd_work+0xa8/0x124 [bluetooth]) >>>>> [ 229.277005] [<bf3cb334>] (hci_cmd_work [bluetooth]) from [<c036f154>] (process_one_work+0x43c/0x83c) >>>>> [ 229.286689] [<c036f154>] (process_one_work) from [<c0370934>] (worker_thread+0x290/0x40c) >>>>> [ 229.295355] [<c0370934>] (worker_thread) from [<c0376784>] (kthread+0x14c/0x168) >>>>> [ 229.303195] [<c0376784>] (kthread) from [<c03080d0>] (ret_from_fork+0x14/0x24) >>>>> >>>>> It results in the first HCI command going through and then every other failing. >>>>> >>>>> = Index Info: 00:00:00:00:00:00 (Broadcom Corporation) >>>>> < HCI Command: Broadcom Update UART Baud Rate (0x3f|0x0018) plen 6 >>>>> Encoded baud rate: Not used (0x0000) >>>>> Explicit baud rate: 2000000 Mbps >>>>>> HCI Event: Command Complete (0x0e) plen 4 >>>>> Broadcom Update UART Baud Rate (0x3f|0x0018) ncmd 1 >>>>> Status: Success (0x00) >>>>> < HCI Command: Reset (0x03|0x0003) plen 0 >>>>> >>>>> The HCI Reset command actually times out. >>>>> >>>>> [ 231.349802] Bluetooth: hci0 command 0x0c03 tx timeout >>>>> >>>>> What we really need is some kernel specific debug tracing when driver change baud rate etc. to show up in btmon. Drivers need the capability to insert HCI transport level specifics into monitoring interface. >>>> >>>> Thanks for noticing this, I've have that exact backlog sitting there >>>> to send out but I'd just not got to it yet, let me know if there's >>>> anything that needs tweaking on the Fedora side or patch. >>> >>> does it actually work for you? I didn’t get it running with the F27 kernel. I had issues with the initial baud rate using btattach in some cases. Does this go away if you use 115200 as max baud rate? >> >> No, not yet, I got to the point it would see an interface but that >> didn't have a MAC address, the patch series has also done something >> weird with serial consoles that I need to debug. I was wondering if it >> still needs the newer firmware rev that various distros have pulled >> in. > > is that the AA:AA:AA.. address? If so, we really need to blacklist that one and mark it with quirk for invalid BD_ADDR. However I am not even getting that far since the command above is the first command send to the hardware. No, it's all zeros, I'll try and spend some time on it this afternoon to reproduce what I was getting. Peter -- To unsubscribe from this list: send the line "unsubscribe linux-bluetooth" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
