This is patchset V2 which reorganises hci_uart_tty_close() to overcome a design flaw related to the proper closure of the Data Link protocol layer. In the worst case scenario a kernel crash occurs. Previous Discussions ==================== Please refer to the discussion on my RFC patchset V1 that can be found here: https://www.spinics.net/lists/linux-bluetooth/msg70077.html Changes between V1 and V2 ========================= 1. Implemented some minor code style changes that were suggested by Marcel Holtmann. 2. Reordered some of the patches to better group together related changes. Terms used ========== Data Link protocol: This refers to the serial link protocol used by the UART based Bluetooth Radio Module. h4, BCSP and h5 are examples of Data Link protocols and there are other protocols available. Data Link protocol layer: This refers to the "proto" protocols that implement the Data Link protocol on the Linux side of the UART link. These protocols are implemented with a function pointer interface and therefore a specific Data Link protocol can be bound within the UART HCI driver. Overview of Data Link protocol data flow ======================================== The Data Link protocol layer uses serial protocol frames to transport information such as HCI messages to the Bluetooth Radio Module. Internally within the Linux kernel, the Data Link protocol layer supplies protocol frames via the HCI UART LDISC and TTY layers to the UART driver. Any breakage in this data "pipe" will cause a disruption of the communications with the Bluetooth Radio Module. Overview of Design Flaw ======================= There are a number of issues relating to the implementation of hci_uart_tty_close(). The areas of concern are: a) poor locking of hu->proto->close() with respect to the other "proto" function pointers. This means hu->proto->close() can asynchronously remove resources used by the other "proto" function pointers resulting in malfunctions and kernel crashes. b) tearing down parts of the data "pipe" between the Data Link protocol layer and the UART driver despite attempting to send HCI commands and trying to handle retransmissions within hci_uart_tty_close(). This results in a loss of communications with the Bluetooth Radio Module. Note that a loss of communications can cause the Data Link protocol layer to independently attempt to retransmit such as in the case of BCSP. c) suspect HCI_QUIRK_RESET_ON_CLOSE has been broken for many years because it is not possible to get the HCI RESET command successfully ACK'ed due to the data "pipe" being cut in multiple places during the execution of tty_ldisc_close(). Please note the issue is independent of the implementation of the Data Link protocol layer. BCSP closedown scenarios have been used as an example. Test cases ========== Test 1 ------ Setup Bluetooth to use a BCSP based UART Bluetooth Radio Module. In this case use the Bluez hciattach utility. Then kill the userland hciattach program by doing killall hciattach When hciattach terminates, SIGTERM handling causes ioctl TIOCSETD to run kernel function tty_set_ldisc(). Test 2 ------ Setup Bluetooth to use a BCSP based UART Bluetooth Radio Module. In this case use the Bluez btattach utility. Note that btattach does not establish a BCSP connection due to missing some BCSP protocol implementation. However, this is ideal in exposing the design flaw. Here is an example test script that can trigger a Bluetooth kernel crash in relation to hci_uart_tty_close(). #!/bin/bash let i=1 while [ true ] do echo "loop $i" ./btattach -A /dev/ttyUSB0 -P bcsp & sleep 5 echo "now killing..." killall btattach i=$(($i + 1)) done Kernel crashes within 10 minutes of starting the script. h4 can also be shown to fail by using ./btattach -A /dev/ttyUSB0 -P h4 & Note that in my test run, h4 was communicating with a BCSP enabled Bluetooth Radio Module. The probability of a crash is increased when poor communications occur. When btattach gets a SIGTERM, the program terminates with a group_exit() system call which causes tty_set_ldisc() to run to perform clean-up. Analysis of hci_uart_tty_close() callstack ========================================== Crash 1 - Sending HCI RESET command due to HCI_QUIRK_RESET_ON_CLOSE ------- >From tests 1 and 2 the callstack can be: tty_set_ldisc() takes a tty ref lock via tty_ldisc_lock tty_ldisc_close() hci_uart_tty_close() hci_unregister_dev() hci_dev_do_close() __hci_req_sync() which tries to send a HCI RESET command which depends on HCI_QUIRK_RESET_ON_CLOSE being enabled and that is the default condition. This is done by queueing up the HCI RESET command which adds a work-item to the hdev->workqueue and waits 2 seconds for a response Subsequently in a parallel thread to hci_uart_tty_close() hdev->workqueue runs and processes the work-item by calling hci_cmd_work() hci_send_frame() hci_uart_send_frame() hci_uart_tx_wakeup() to schedule hci_uart_write_work() via the work queue hu->write_work Subsequently in a parallel thread to hci_uart_tty_close() hci_uart_write_work() hci_uart_dequeue() hu->proto->dequeue() bcsp_dequeue() tty->ops->write() to write the BCSP frame to the UART driver via TTY layer Subsequently in a parallel thread to hci_uart_tty_close() BCSP re-transmission timer expires after 250ms due to no ACK from the Bluetooth Radio Module. bcsp_timed_event() hci_uart_tx_wakeup() to schedule hci_uart_write_work() via the work queue hu->write_work Subsequently in a parallel thread to hci_uart_tty_close() hci_uart_write_work() hci_uart_dequeue() hu->proto->dequeue() bcsp_dequeue() tty->ops->write() to write the BCSP frame to the UART driver via TTY layer Subsequently in a parallel thread to hci_uart_tty_close() BCSP re-transmission timer expires after 250ms due to no ACK from the Bluetooth Radio Module. bcsp_timed_event() hci_uart_tx_wakeup() to schedule hci_uart_write_work() via the work queue hu->write_work Subsequently in a parallel thread to hci_uart_tty_close() hci_uart_write_work() hci_uart_dequeue() hu->proto->dequeue() bcsp_dequeue() tty->ops->write() to write the BCSP frame to the UART driver via TTY layer etc. BCSP attempts to retransmit every 250ms during the execution of hci_uart_tty_close() until bcsp_close() is called via hu->proto->close(). Here is an example kernel crash log for kernel 4.10.5 + debug (sorry for the bad kernel version string 4.10.54.10.5_debug+) [ 1561.709737] BUG: unable to handle kernel NULL pointer dereference at 0000000000000044 [ 1561.709829] IP: _raw_spin_lock_irqsave+0x22/0x40 [ 1561.709862] PGD 0 [ 1561.709889] Oops: 0002 1 SMP [ 1561.709911] Modules linked in: ftdi_sio rfcomm hci_uart btqca xt_set ip_set_hash_ip nf_log_ipv6 ip_set nf_log_ipv4 nf_log_common xt_LOG ip6table_nat nf_nat_ipv6 xt_recent iptable_nat nf_nat_ipv4 ipt_REJECT nf_reject_ipv4 iptable_mangle iptable_raw nf_conntrack_ipv4 nf_defrag_ipv4 xt_comment ip6t_REJECT nf_reject_ipv6 xt_addrtype bridge stp llc xt_mark ip6table_mangle nf_nat_tftp nf_nat_snmp_basic nf_conntrack_snmp xt_tcpudp nf_nat_sip xt_CT nf_nat_pptp nf_nat_proto_gre nf_nat_irc ip6table_raw nf_nat_h323 xt_multiport nf_nat_ftp nf_nat_amanda nf_conntrack_ipv6 nf_defrag_ipv6 xt_conntrack nf_nat nf_conntrack_tftp nf_conntrack_sip nf_conntrack_sane nf_conntrack_pptp nf_conntrack_proto_gre nf_conntrack_netlink nfnetlink nf_conntrack_netbios_ns nf_conntrack_broadcast nf_conntrack_irc nf_conntrack_h323 [ 1561.710172] nf_conntrack_ftp ts_kmp nf_conntrack_amanda nf_conntrack iptable_filter ip_tables ip6table_filter ip6_tables x_tables lockd grace ctr ccm af_packet bnep msr usbserial uvcvideo btusb btrtl arc4 brcmsmac btbcm videobuf2_vmalloc btintel cordic videobuf2_memops bluetooth intel_powerclamp brcmutil videobuf2_v4l2 videobuf2_core mac80211 videodev coretemp kvm_intel kvm joydev media cfg80211 iTCO_wdt iTCO_vendor_support snd_hda_codec_hdmi snd_hda_codec_realtek psmouse snd_hda_codec_generic toshiba_acpi input_leds bcma snd_hda_intel irqbypass snd_hda_codec toshiba_bluetooth cpufreq_ondemand sparse_keymap crc32c_intel cpufreq_conservative industrialio snd_hda_core serio_raw wmi rfkill thermal cpufreq_powersave battery ac snd_hwdep snd_pcm acpi_cpufreq snd_timer snd toshiba_haps mei_me mei e1000e [ 1561.718028] fjes soundcore evdev ptp lpc_ich shpchp pps_core intel_ips tpm_tis tpm_tis_core nvram tpm sch_fq_codel sunrpc ipv6 crc_ccitt autofs4 hid_generic usbhid hid sdhci_pci mmc_block sdhci sr_mod ehci_pci ehci_hcd mmc_core usbcore usb_common i915 video button i2c_algo_bit drm_kms_helper drm [last unloaded: ftdi_sio] [ 1561.721317] CPU: 1 PID: 4473 Comm: kworker/1:0 Not tainted 4.10.54.10.5_debug+ #12 [ 1561.722981] Hardware name: TOSHIBA Satellite R630/Portable PC, BIOS Version 1.40 07/20/2010 [ 1561.724660] Workqueue: events hci_uart_write_work [hci_uart] [ 1561.726377] task: ffff98d9b4f15100 task.stack: ffffa868c1178000 [ 1561.728568] RIP: 0010:_raw_spin_lock_irqsave+0x22/0x40 [ 1561.730355] RSP: 0000:ffffa868c117bda8 EFLAGS: 00010046 [ 1561.731993] RAX: 0000000000000000 RBX: 0000000000000296 RCX: 0000000000079ad6 [ 1561.733646] RDX: 0000000000000001 RSI: ffff98da77c5c580 RDI: 0000000000000044 [ 1561.735314] RBP: ffffa868c117bdb0 R08: 000000000001c5a0 R09: ffffffff9965a54a [ 1561.736991] R10: fffff48441dc9a80 R11: ffff98da73403700 R12: 0000000000000030 [ 1561.738641] R13: 0000000000000044 R14: 0000000000000030 R15: ffff98d9b4e50000 [ 1561.740288] FS: 0000000000000000(0000) GS:ffff98da77c40000(0000) knlGS:0000000000000000 [ 1561.741940] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1561.743585] CR2: 0000000000000044 CR3: 0000000128d1a000 CR4: 00000000000006e0 [ 1561.745238] Call Trace: [ 1561.746882] skb_dequeue+0x1d/0x70 [ 1561.748512] bcsp_dequeue+0x27/0x180 [hci_uart] [ 1561.750130] ? kfree_skbmem+0x5a/0x60 [ 1561.751742] hci_uart_write_work+0xc4/0x100 [hci_uart] [ 1561.753356] process_one_work+0x151/0x410 [ 1561.754930] worker_thread+0x69/0x4b0 [ 1561.756507] kthread+0x114/0x150 [ 1561.758076] ? rescuer_thread+0x340/0x340 [ 1561.759636] ? kthread_park+0x90/0x90 [ 1561.761191] ret_from_fork+0x2c/0x40 [ 1561.762693] Code: 89 e5 e8 82 96 98 ff 5d c3 66 66 66 66 90 55 48 89 e5 53 9c 58 66 66 90 66 90 48 89 c3 fa 66 66 90 66 66 90 31 c0 ba 01 00 00 00 <f0> 0f b1 17 85 c0 75 06 48 89 d8 5b 5d c3 89 c6 e8 29 83 98 ff [ 1561.766034] RIP: _raw_spin_lock_irqsave+0x22/0x40 RSP: ffffa868c117bda8 [ 1561.768033] CR2: 0000000000000044 [ 1561.774555] --[ end trace 51cc1d3575c0e559 ]-- Crash 2 - Sending HCI commands but get no ACKs ------- Using test 2 and h4, a similar crash could be triggered for h4_dequeue(). In this case HCI is attempting to send multiple HCI commands. tty_set_ldisc() takes a tty ref lock via tty_ldisc_lock tty_ldisc_close() hci_uart_tty_close() hci_unregister_dev() hci_dev_do_close() HCI commands become queued up by adding work-items to the hdev->workqueue. Subsequently in a parallel thread to hci_uart_tty_close() hdev->workqueue runs and processes a work-item by calling hci_cmd_work() hci_send_frame() hci_uart_send_frame() hci_uart_tx_wakeup() to schedule hci_uart_write_work() via the work queue hu->write_work Subsequently in a parallel thread to hci_uart_tty_close() hci_uart_write_work() hci_uart_dequeue() hu->proto->dequeue() tty->ops->write() to write the h4 frame to the UART driver via TTY layer Subsequently in a parallel thread to hci_uart_tty_close() hdev->workqueue runs and processes a work-item by calling hci_cmd_work() hci_send_frame() hci_uart_send_frame() hci_uart_tx_wakeup() to schedule hci_uart_write_work() via the work queue hu->write_work Subsequently in a parallel thread to hci_uart_tty_close() hci_uart_write_work() hci_uart_dequeue() hu->proto->dequeue() tty->ops->write() to write the h4 frame to the UART driver via TTY layer etc. Note that HCI TX timeouts occur. Here is an example kernel crash log for kernel 4.10.5 + debug (sorry for the bad kernel version string 4.10.54.10.5_debug+) [ 563.702430] BUG: unable to handle kernel NULL pointer dereference at 000000000000001c [ 563.702491] IP: _raw_spin_lock_irqsave+0x22/0x40 [ 563.702520] PGD 13230e067 [ 563.702521] PUD 1238d6067 [ 563.702540] PMD 0 [ 563.704521] Oops: 0002 1 SMP [ 563.706215] Modules linked in: hci_uart btqca nf_log_ipv6 ip6table_nat nf_nat_ipv6 ip6t_REJECT nf_reject_ipv6 ip6table_mangle xt_set ip_set_hash_ip ip_set nf_log_ipv4 nf_log_common xt_LOG xt_recent iptable_nat nf_nat_ipv4 xt_comment ipt_REJECT nf_reject_ipv4 xt_addrtype bridge stp llc xt_mark iptable_mangle xt_tcpudp iptable_raw nf_conntrack_ipv4 nf_defrag_ipv4 xt_CT nf_nat_tftp nf_nat_snmp_basic nf_conntrack_snmp ip6table_raw nf_nat_sip xt_multiport nf_nat_pptp nf_nat_proto_gre nf_nat_irc nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_h323 nf_nat_ftp xt_conntrack nf_nat_amanda nf_nat nf_conntrack_tftp nf_conntrack_sip nf_conntrack_sane nf_conntrack_pptp nf_conntrack_proto_gre nf_conntrack_netlink nfnetlink nf_conntrack_netbios_ns nf_conntrack_broadcast nf_conntrack_irc nf_conntrack_h323 nf_conntrack_ftp [ 563.715634] ts_kmp nf_conntrack_amanda nf_conntrack iptable_filter ip_tables ip6table_filter ip6_tables x_tables lockd grace ctr ccm af_packet bnep msr arc4 brcmsmac uvcvideo cordic brcmutil ftdi_sio videobuf2_vmalloc usbserial intel_powerclamp mac80211 videobuf2_memops btusb videobuf2_v4l2 btrtl coretemp snd_hda_codec_hdmi btbcm videobuf2_core btintel kvm_intel snd_hda_codec_realtek bluetooth kvm videodev joydev cfg80211 snd_hda_codec_generic media snd_hda_intel snd_hda_codec psmouse snd_hda_core irqbypass e1000e snd_hwdep input_leds snd_pcm iTCO_wdt iTCO_vendor_support serio_raw crc32c_intel toshiba_acpi snd_timer ptp mei_me fjes bcma snd mei thermal sparse_keymap toshiba_haps industrialio lpc_ich soundcore battery ac pps_core shpchp intel_ips toshiba_bluetooth wmi rfkill tpm_tis tpm_tis_core [ 563.726159] tpm cpufreq_ondemand cpufreq_conservative cpufreq_powersave acpi_cpufreq evdev nvram sunrpc sch_fq_codel ipv6 crc_ccitt autofs4 hid_generic usbhid hid sdhci_pci mmc_block sdhci sr_mod ehci_pci ehci_hcd mmc_core usbcore usb_common i915 video button i2c_algo_bit drm_kms_helper drm [ 563.730623] CPU: 0 PID: 29 Comm: kworker/0:1 Not tainted 4.10.54.10.5_debug+ #13 [ 563.732862] Hardware name: TOSHIBA Satellite R630/Portable PC, BIOS Version 1.40 07/20/2010 [ 563.735127] Workqueue: events hci_uart_write_work [hci_uart] [ 563.737376] task: ffffa03f32951b00 task.stack: ffffbc4ec0768000 [ 563.739620] RIP: 0010:_raw_spin_lock_irqsave+0x22/0x40 [ 563.741839] RSP: 0018:ffffbc4ec076bdd8 EFLAGS: 00010046 [ 563.744059] RAX: 0000000000000000 RBX: 0000000000000202 RCX: ffffa03f37c1cd60 [ 563.746286] RDX: 0000000000000001 RSI: ffffa03f37c18ae0 RDI: 000000000000001c [ 563.748493] RBP: ffffbc4ec076bde0 R08: ffffa03f32332380 R09: 0000000000000001 [ 563.750690] R10: ffffe9de427ce800 R11: ffffa03f33498600 R12: 0000000000000008 [ 563.752884] R13: 000000000000001c R14: ffffa03e79b1ad38 R15: ffffa03e79b1a240 [ 563.755075] FS: 0000000000000000(0000) GS:ffffa03f37c00000(0000) knlGS:0000000000000000 [ 563.757260] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 563.759426] CR2: 000000000000001c CR3: 000000011d7a3000 CR4: 00000000000006f0 [ 563.761610] Call Trace: [ 563.763798] skb_dequeue+0x1d/0x70 [ 563.765975] h4_dequeue+0x16/0x20 [hci_uart] [ 563.768128] hci_uart_write_work+0xc4/0x100 [hci_uart] [ 563.770262] process_one_work+0x151/0x410 [ 563.772368] worker_thread+0x69/0x4b0 [ 563.774466] kthread+0x114/0x150 [ 563.776519] ? rescuer_thread+0x340/0x340 [ 563.778546] ? kthread_park+0x90/0x90 [ 563.780566] ret_from_fork+0x2c/0x40 [ 563.782559] Code: 89 e5 e8 82 96 98 ff 5d c3 66 66 66 66 90 55 48 89 e5 53 9c 58 66 66 90 66 90 48 89 c3 fa 66 66 90 66 66 90 31 c0 ba 01 00 00 00 <f0> 0f b1 17 85 c0 75 06 48 89 d8 5b 5d c3 89 c6 e8 29 83 98 ff [ 563.786800] RIP: _raw_spin_lock_irqsave+0x22/0x40 RSP: ffffbc4ec076bdd8 [ 563.788940] CR2: 000000000000001c [ 563.798389] --[ end trace 326429e7baa9f359 ]-- Detailed analysis ================= The failure can be rare due to the following mitigations: a) the Data Link protocol layer might be idle when hci_uart_tty_close() runs. b) the system never shuts down Bluetooth so hci_uart_tty_close() does not run. c) HCI_QUIRK_RESET_ON_CLOSE is disabled so the HCI RESET command is not sent. Please note that disabling HCI_QUIRK_RESET_ON_CLOSE helps to reduce the probability that a crash occurs. However, it is not a fix. It can be seen that the following threads can be running concurrently with hci_uart_tty_close(): a) hci_cmd_work() via the work queue hdev->workqueue b) hci_uart_write_work() via the work queue hu->write_work c) Data Link protocol layer retransmission timer such as bcsp_timed_event() In order to send a HCI command the Data Link protocol layer must be able to send and receive frames from the UART port that is physically connected to the UART based Bluetooth Radio Module. If this data "pipe" is broken then the Data Link protocol layer may perform retransmissions such as in the case of BCSP. In addition, a loss of communications causes the HCI command to not be ACK'ed so causes a HCI command timeout to occur. In the case of HCI_QUIRK_RESET_ON_CLOSE, the sending of the HCI RESET command has a 2 second timeout which will block __hci_req_sync() for up to 2 seconds. The hu->proto->dequeue() kernel crash occurs because hu->proto->close() was called which removes the resources needed by hu->proto->dequeue(). This causes a NULL pointer dereference kernel crash to occur when hu->proto->dequeue() executes. The reason why hu->proto->close() can run before or during hu->proto->dequeue() is because the call to cancel_work_sync(&hu->write_work) is ineffective. This is because hci_cmd_work() and BCSP bcsp_timed_event() can schedule work-items after the cancel_work_sync() completed. Note that flushing can corrupt any protocol serial frames being sent from the Data Link protocol layer to the UART driver and this is undesirable. Solution ======== Reorganise hci_uart_tty_close() so that hci_unregister_dev() can run with no interference to the data "pipe" between the Data Link protocol layer such as BCSP and the UART driver. The patchset cleans up the HCI_UART_REGISTERED and HCI_UART_PROTO_READY flag handling so that: a) hdev is only valid when HCI_UART_REGISTERED is in the set state. b) the "proto" Data Link function pointers can only be used when HCI_UART_PROTO_READY is in the set state. The most important patch is "Bluetooth: hci_ldisc: Use rwlocking to avoid closing proto races" This patch adds rwlocking around the clearing of the flag HCI_UART_PROTO_READY. This is because the atomic flag HCI_UART_PROTO_READY cannot always prevent a thread using a Data Link protocol layer function pointer during or after closure of the Data Link protocol layer. This can result in a kernel crash. Remember that the BCSP retransmission handling runs in a separate thread and tries to send a new frame. Therefore there is a small window of a race condition for the flag HCI_UART_PROTO_READY to be seen in the set state and then calls the "proto" function pointer after the Data Link protocol layer has been closed, resulting in a kernel crash. Overview of patches ------------------- The patches were rebased onto the bluetooth-next/master branch commit: 3eed895 Bluetooth: L2CAP: Don't return -EAGAIN if out of credits Tidy-up patches (mainly for h5 binding error handling) Bluetooth: hci_ldisc: Add missing return in hci_uart_init_work() Bluetooth: hci_ldisc: Ensure hu->hdev set to NULL before freeing hdev Bluetooth: hci_ldisc: Add missing clear HCI_UART_PROTO_READY Adds a comment to warn that hci_unregister_dev() may send a HCI RESET command Bluetooth: hci_ldisc: Add HCI RESET comment to hci_unregister_dev() call Simplifies the relationship between HCI_UART_REGISTERED and HCI_UART_PROTO_READY Bluetooth: hci_ldisc: Separate flag handling in hci_uart_tty_close() Prevents "proto" functions being used immediately before and after hu->proto->close() Bluetooth: hci_ldisc: Add protocol check to hci_uart_send_frame() Bluetooth: hci_ldisc: Add protocol check to hci_uart_dequeue() Bluetooth: hci_ldisc: Add protocol check to hci_uart_tx_wakeup() Bluetooth: hci_ldisc: Use rwlocking to avoid closing proto races Prevents the "data" pipe being cut too early inside hci_uart_tty_close() Bluetooth: hci_ldisc: Tidy-up HCI_UART_REGISTERED in hci_uart_tty_close() Bluetooth: hci_ldisc: hci_uart_tty_close() move hci_uart_close() Bluetooth: hci_ldisc: hci_uart_tty_close() detach tty after last msg Bluetooth: hci_ldisc: hci_uart_tty_close() move cancel_work_sync() Bluetooth: hci_ldisc: hci_uart_tty_close() free hu->tx_skb Bluetooth: hci_ldisc: Simplify flushing Prevent concurrency of hci_uart_tty_ioctl() with hci_uart_tty_close() Bluetooth: hci_ldisc: Add ioctl_mutex avoiding concurrency Further work ============ This patchset tackles the issues of hci_uart_tty_close(). However, the TTY layer needs investigation because tty_set_ldisc() has a tty ref lock during the execution of hci_uart_tty_close() which: a) prevents flush_to_ldisc() from passing the received UART data to the Data Link protocol layer. b) prevents hci_uart_tty_wakeup() from passing the Data Link protocol layer's transmission data to the UART driver. Therefore, the TTY layer cuts the data "pipe" during the execution of hci_uart_tty_close() causing a loss of communications with the Bluetooth Radio Module. This patchset does not attempt to fix the TTY layer. This means that the HCI_QUIRK_RESET_ON_CLOSE will remain being unsuccessful in sending the HCI RESET command. In fact, all attempts at sending an HCI command during hci_uart_tty_close() will still fail. Dean Jenkins (16): Bluetooth: hci_ldisc: Add missing return in hci_uart_init_work() Bluetooth: hci_ldisc: Ensure hu->hdev set to NULL before freeing hdev Bluetooth: hci_ldisc: Add missing clear HCI_UART_PROTO_READY Bluetooth: hci_ldisc: Add HCI RESET comment to hci_unregister_dev() call Bluetooth: hci_ldisc: Separate flag handling in hci_uart_tty_close() Bluetooth: hci_ldisc: Add protocol check to hci_uart_send_frame() Bluetooth: hci_ldisc: Add protocol check to hci_uart_dequeue() Bluetooth: hci_ldisc: Add protocol check to hci_uart_tx_wakeup() Bluetooth: hci_ldisc: Use rwlocking to avoid closing proto races Bluetooth: hci_ldisc: Tidy-up HCI_UART_REGISTERED in hci_uart_tty_close() Bluetooth: hci_ldisc: hci_uart_tty_close() move hci_uart_close() Bluetooth: hci_ldisc: hci_uart_tty_close() detach tty after last msg Bluetooth: hci_ldisc: hci_uart_tty_close() move cancel_work_sync() Bluetooth: hci_ldisc: hci_uart_tty_close() free hu->tx_skb Bluetooth: hci_ldisc: Simplify flushing Bluetooth: hci_ldisc: Add ioctl_mutex avoiding concurrency drivers/bluetooth/hci_ldisc.c | 105 ++++++++++++++++++++++++++++++++---------- drivers/bluetooth/hci_uart.h | 3 ++ 2 files changed, 84 insertions(+), 24 deletions(-) -- 2.7.4 -- To unsubscribe from this list: send the line "unsubscribe linux-bluetooth" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
