Hi Ilya,
>> Device Tree bindings to configure the Broadcom Bluetooth UART device.
>>
>> Signed-off-by: Ilya Faenson <ifaenson@xxxxxxxxxxxx>
>> ---
>> .../devicetree/bindings/net/bluetooth/btbcm.txt | 82 ++++++++++++++++++++++
>> 1 file changed, 82 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/net/bluetooth/btbcm.txt
>>
>> diff --git a/Documentation/devicetree/bindings/net/bluetooth/btbcm.txt b/Documentation/devicetree/bindings/net/bluetooth/btbcm.txt
>> new file mode 100644
>> index 0000000..2679819
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/net/bluetooth/btbcm.txt
>> @@ -0,0 +1,82 @@
>> +btbcm
>> +------
>> +
>> +Required properties:
>> +
>> + - compatible : must be "brcm,brcm-bt-uart".
>> + - tty : tty device connected to this Bluetooth device.
>> +
>> +Optional properties:
>> +
>> + - bt-host-wake-gpios : bt-host-wake input GPIO to be used as an interrupt.
>> +
>> + - bt-wake-gpios : bt-wake output GPIO to be used to suspend / resume device.
>> +
>> + - bt-reg-on-gpios : reg-on output GPIO to be used to power device on/off.
>> +
>> + - oper-speed : Bluetooth device operational baud rate.
>> + Default: 3000000.
>> +
>> + - manual-fc : flow control UART in suspend / resume scenarios.
>> + Default: 0.
>> +
>> + - configure-sleep : configure suspend / resume flag.
>> + Default: false.
>> +
>> + - configure-audio : configure platform PCM SCO flag.
>> + Default: false.
>> +
>> + - pcm-clockmode : PCM clock mode. 0-slave, 1-master.
>> + Default: 0.
>> +
>> + - pcm-fillmethod : PCM fill method. 0 to 3.
>> + Default: 2.
>> +
>> + - pcm-fillnum : PCM number of fill bits. 0 to 3.
>> + Default: 0.
>> +
>> + - pcm-fillvalue : PCM fill value. 0 to 7.
>> + Default: 3.
>> +
>> + - pcm-incallbitclock : PCM interface rate. 0-128Kbps, 1-256Kbps, 2-512Kbps,
>> + 3-1024Kbps, 4-2048Kbps.
>> + Default: 0.
>> +
>> + - pcm-lsbfirst : PCM LSB first. 0 or 1.
>> + Default: 0.
>> +
>> + - pcm-rightjustify : PCM Justify. 0-left, 1-right.
>> + Default: 0.
>> +
>> + - pcm-routing : PCM routing. 0-PCM, 1-SCO over HCI.
>> + Default: 0.
>> +
>> + - pcm-shortframesync : PCM sync. 0-short, 1-long.
>> + Default: 0.
>> +
>> + - pcmsyncmode : PCM sync mode. 0-slave, 1-master.
>> + Default: 0.
>
> I think you meant pcm-syncmode here.
>
> IF: That's right, will change.
>> +
>> +
>> +Example:
>> +
>> + brcm4354_bt_uart: brcm4354-bt-uart {
>
> Since in general the chips and firmware name refer to BCM4354, it might be a really good idea to use bcm4354 here and not confuse people further. I am just trying to avoid confusion here.
>
> IF: You're right, the chip name is BCM4354 but we must use the "brcm" prefix in the device tree bindings. Alright, I will change these to start from the "bcm" but will keep the "brcm" in the "compatible" strings. That would also be somewhat confusing but possibly not as confusing as now.
I think Arend had a good proposal there. If I remember correctly then when it refers to Broadcom as generic DT identifier, then it is brcm. If it is device specific use the actual name bcm1234. SO things like brcm,bcm1234 made sense to at least me.
Regards
Marcel
--
To unsubscribe from this list: send the line "unsubscribe linux-bluetooth" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
