Hi Szymon, > This command should only be used if remote device reports that it > supports extended features. Otherwise command will fail and connection > will be dropped. > > Some devices support SSP but don't support extended features so > current check for SSP support is not enought. > > Instead of checking for SSP support just check if both ends support > Extended Feature. > > < HCI Command: Create Connection (0x01|0x0005) plen 13 > Address: D0:9C:30:00:19:6F (Foster Electric Company, Limited) > Packet type: 0xcc18 > DM1 may be used > DH1 may be used > DM3 may be used > DH3 may be used > DM5 may be used > DH5 may be used > Page scan repetition mode: R1 (0x01) > Page scan mode: Mandatory (0x00) > Clock offset: 0x94c8 > Role switch: Allow slave (0x01) >> HCI Event: Command Status (0x0f) plen 4 > Create Connection (0x01|0x0005) ncmd 1 > Status: Success (0x00) >> HCI Event: Connect Complete (0x03) plen 11 > Status: Success (0x00) > Handle: 5 > Address: D0:9C:30:00:19:6F (Foster Electric Company, Limited) > Link type: ACL (0x01) > Encryption: Disabled (0x00) > < HCI Command: Read Remote Supported Features (0x01|0x001b) plen 2 > Handle: 5 >> HCI Event: Command Status (0x0f) plen 4 > Read Remote Supported Features (0x01|0x001b) ncmd 1 > Status: Success (0x00) >> HCI Event: Page Scan Repetition Mode Change (0x20) plen 7 > Address: D0:9C:30:00:19:6F (Foster Electric Company, Limited) > Page scan repetition mode: R1 (0x01) >> HCI Event: Read Remote Supported Features (0x0b) plen 11 > Status: Success (0x00) > Handle: 5 > Features: 0xff 0xff 0x8f 0xfe 0xdb 0xff 0x5b 0x07 > 3 slot packets > 5 slot packets > Encryption > Slot offset > Timing accuracy > Role switch > Hold mode > Sniff mode > Park state > Power control requests > Channel quality driven data rate (CQDDR) > SCO link > HV2 packets > HV3 packets > u-law log synchronous data > A-law log synchronous data > CVSD synchronous data > Paging parameter negotiation > Power control > Transparent synchronous data > Broadcast Encryption > Enhanced Data Rate ACL 2 Mbps mode > Enhanced Data Rate ACL 3 Mbps mode > Enhanced inquiry scan > Interlaced inquiry scan > Interlaced page scan > RSSI with inquiry results > Extended SCO link (EV3 packets) > EV4 packets > EV5 packets > AFH capable slave > AFH classification slave > LE Supported (Controller) > 3-slot Enhanced Data Rate ACL packets > 5-slot Enhanced Data Rate ACL packets > Sniff subrating > Pause encryption > AFH capable master > AFH classification master > Enhanced Data Rate eSCO 2 Mbps mode > Enhanced Data Rate eSCO 3 Mbps mode > 3-slot Enhanced Data Rate eSCO packets > Extended Inquiry Response > Simultaneous LE and BR/EDR (Controller) > Secure Simple Pairing > Encapsulated PDU > Non-flushable Packet Boundary Flag > Link Supervision Timeout Changed Event > Inquiry TX Power Level > Enhanced Power Control > < HCI Command: Read Remote Extended Features (0x01|0x001c) plen 3 > Handle: 5 > Page: 1 >> HCI Event: Command Status (0x0f) plen 4 > Read Remote Extended Features (0x01|0x001c) ncmd 1 > Status: Command Disallowed (0x0c) > < HCI Command: Read Clock Offset (0x01|0x001f) plen 2 > Handle: 5 >> HCI Event: Command Status (0x0f) plen 4 > Read Clock Offset (0x01|0x001f) ncmd 1 > Status: Success (0x00) > < HCI Command: Disconnect (0x01|0x0006) plen 3 > Handle: 5 > Reason: Remote User Terminated Connection (0x13) > > Signed-off-by: Szymon Janc <szymon.janc@xxxxxxxxx> > --- > > V2 - check for lmp_ext_feat_capable on both ends instead of > ssp check as suggested by Marcel > > net/bluetooth/hci_event.c | 3 ++- > 1 file changed, 2 insertions(+), 1 deletion(-) patch has been applied to bluetooth-next tree. Regards Marcel -- To unsubscribe from this list: send the line "unsubscribe linux-bluetooth" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
