Hi, On 4 September 2014 11:58, Lukasz Rymanowski <lukasz.rymanowski@xxxxxxxxx> wrote: > --- > android/hal-ipc-api.txt | 317 ++++++++++++++++++++++++++++++++++++++++++++++++ > 1 file changed, 317 insertions(+) > > diff --git a/android/hal-ipc-api.txt b/android/hal-ipc-api.txt > index ae62c10..6061ebb 100644 > --- a/android/hal-ipc-api.txt > +++ b/android/hal-ipc-api.txt > @@ -2078,3 +2078,320 @@ Notifications: > > Notification parameters: Status (4 octets) > Handle (4 octets) > + > + > +Bluetooth Handsfree Client HAL (ID 10) > +====================================== > + > +Android HAL name: "hf_client" (BT_PROFILE_HF_CLIENT_ID) > + > +Commands and response: > + > + Opcode 0x00 - Error response > + > + Valid status values: 0x01 = Fail > + 0x02 = Not ready > + 0x03 = No memory > + 0x04 = Busy > + 0x05 = Done (already completed) > + 0x06 = Unsupported > + 0x07 = Parameter invalid > + 0x08 = Unhandled > + 0x09 = Authentication failure > + 0x0a = Remote device down > + > + Opcode 0x01 - Connect command/respose > + > + Command parameters: Remote address (6 octects) > + Response parameters: <none> > + > + In case of an error, the error response will be returned. > + > + Opcode 0x02 - Disonnect command/response > + > + Command parameters: Remote address (6 octetcs) > + Response parameters: <none> > + > + In case of an error, the error response will be returned. > + > + Opcode 0x03 - Connect Audio command/response > + > + Command parameters: Remote address (6 octets) > + Response parameters: <none> > + > + In case of an error, the error response will be returned. > + > + Opcode 0x04 - Disconnect Audio command/response > + > + Command parameters: Remote address (6 octets) > + Response parameters: <none> > + > + In case of an error, the error response will be returned. > + > + Opcode 0x05 - Start Voice Recognition command/response > + > + Command parameters: <none> > + Response parameters: <none> > + > + In case of an error, the error response will be returned. > + > + Opcode 0x06 - Stop Voice Recognition command/response > + > + Command parameters: <none> > + Response parameters: <none> > + > + In case of an error, the error response will be returned. > + > + Opcode 0x07 - Volume Control command/response > + > + Command parameters: Volume type (1 octet) > + Volume (1 octet) > + Response parameters: <none> > + > + Valid volume types: 0x00 = Speaker > + 0x01 = Microphone > + > + In case of an error, the error response will be returned. > + > + Opcode 0x08 - Dial command/response > + > + Command parameters: Number (string) > + Response parameters: <none> > + > + In case of an error, the error response will be returned. > + > + Opcode 0x09 - Dial Memory command/response > + > + Command parameters: Location (1 octet) > + Response parameters: <none> > + > + In case of an error, the error response will be returned. > + > + Opcode 0x10 - Handle Call Action command/response > + > + Command parameters: Action (1 octet) > + Call Index (1 octet) > + Response parameters: <none> > + > + Valid actions: 0x00 = CHLD_0 > + 0x01 = CHLD_1 > + 0x02 = CHLD_2 > + 0x03 = CHLD_3 > + 0x04 = CHLD_4 > + 0x05 = CHLD_1x > + 0x06 = CHLD_2x > + 0x07 = ATA > + 0x08 = CHUP > + 0x09 = BTRH_0 > + 0x10 = BTRH_1 > + 0x11 = BTRH_2 > + > + In case of an error, the error response will be returned. > + > + Opcode 0x11 - Query Current Calls commad/response > + > + Command parameters: <none> > + Response parameters: <none> > + > + In case of an error, the error response will be returned. > + > + Opcode 0x12 - Query Current Operator Name > + > + Command parameters: <none> > + Response parameters: <none> > + > + In case of an error, the error response will be returned. > + > + Opcode 0x13 - Retrieve Subscriber Info command/response > + > + Command parameters: <none> > + Response parameters: <none> > + > + In case of an error, the error response will be returned. > + > + Opcode 0x14 - Send DTMF Code command/response > + > + Command parameters: Code (1 octet) > + Response parameters: <none> > + > + In case of an error, the error response will be returned. > + > + Opcode 0x15 - Request Last Voice Tag Number command/response > + > + Command parameters: <none> > + Response parameters: <none> > + > + In case of an error, the error response will be returned. > + > +Notifications: > + > + Opcode 0x81 - Connection State Changed notification > + > + Notification parameters: State (1 octet) > + Peer Features (1 octet) > + Address (6 octets) > + > + Valid State values: 0x00 = Disconnected > + 0x01 = Connecting > + 0x02 = SLC Connected > + 0x03 = Disconnecting > + > + Note: Peer Features is valid only in SCL Connected state > + > + Opcode 0x82 - Audio State Changed notification > + > + Notification parameters: State (1 octet) > + Address (6 octets) > + > + Valid State values: 0x00 = Disconnected > + 0x01 = Connecting > + 0x02 = Connected > + 0x03 = Connected mSBC > + > + Opcode 0x83 - Voice Recognition State Changed notification > + > + Notification parameters: State (1 octet) > + > + Valid State values: 0x00 = VR Stopped > + 0x01 = VR Started > + > + Opcode 0x84 - Network State Changed notification > + > + Notification parameters: State (1 octet) > + > + Valid State values: 0x00 = Network Not Available > + 0x01 = Network Available > + > + Opcode 0x85 - Network Roaming Type Changed notification > + > + Notification parameters: Type (1 octet) > + > + Valid Type values: 0x00 = Home > + 0x01 = Roaming > + > + Opcode 0x86 - Network Signal Strength notification > + > + Notification parameters: Signal Strength (1 octet) > + > + Opcode 0x86 - Network Battery Level notification there is no network battery level :) will fix. > + > + Notification parameters: Battery Level (1 octet) > + > + Opcode 0x87 - Current Operator Name notification > + > + Notification parameters: Name (string) > + > + Opcode 0x88 - Call Indicatior notification > + > + Notification parameters: Call (1 octet) > + > + Valid Call values: 0x00 = No Call In Progress > + 0x01 = Call In Progress > + > + Opcode 0x89 - Call Setup Indicator notification > + > + Notification parameters: Call Setup (1 octet) > + > + Valid Call Setup values: 0x00 = None > + 0x01 = Incoming > + 0x02 = Outgoing > + 0x03 = Alerting > + > + Opcode 0x8a - Call Held Indicator notification > + > + Notification parameters: Call Held (1 octet) > + > + Valid Call Held values: 0x00 = None > + 0x01 = Hold and Active > + 0x02 = Hold > + > + Opcode 0x8b - Resposne and Hold Status notification > + > + Notification parameters: Status (1 octet) > + > + Valid Status values: 0x00 = Held > + 0x01 = Accept > + 0x02 = Reject > + > + Opcode 0x8c - Calling Line Identification notification > + > + Notification parameters: Number (string) > + > + Note: This will be called only on incoming call if number is > + provided. > + > + Opcode 0x8d - Call Waiting notification > + > + Notification parameters: Nunmber (string) > + > + Opcode 0x8e - Current Calls List notification > + > + Notification parameters: Index (1 octet) > + Direction (1 octet) > + Call State (1 octet) > + Multiparty (1 octet) > + Number (string) > + > + Valid Direction values: 0x00 = Outgoing > + 0x01 = Incoming > + > + Valid Call Sate values: 0x00 = Active > + 0x01 = Held > + 0x02 = Dialing > + 0x03 = Alerting > + 0x04 = Incoming > + 0x05 = Waiting > + 0x06 = Call held by Response and Hold > + > + Valid Multiparty values: 0x00 = Single Call > + 0x01 = Multiparty (conference) Call > + > + Note: Number might be empty > + > + Opcode 0x8f - Volume Changed notification > + > + Notification parameters: Type (1 octet) > + Volume (1 octet) > + > + Valid Type values: 0x00 = Speaker > + 0x01 = Microphone > + > + Opcode 0x90 - Command Complete Callback notification > + > + Notification parameters: Type (1 octet) > + CME (1 octet) > + > + Valid Type values: 0x00 = OK > + 0x01 = Error > + 0x02 = Error no carrier > + 0x03 = Error busy > + 0x04 = Error no answer > + 0x05 = Error delayed > + 0x06 = Error blacklisted > + 0x07 = Error CME > + > + Note: CME parameter is valid only for Error CME type > + > + Opcode 0x91 - Subscriber Service Info Callback notification > + > + Notification parameters: Name (string) > + Type (1 octet) > + > + Valid Type values: 0x00 = Service unknown > + 0x01 = Service voice > + 0x02 = Service fax > + > + Opcode 0x92 - In Band Ring Settings Callback notification > + > + Notification parameters: State (1 octet) > + > + Valid State values: 0x00 = In band ringtone not provided > + 0x01 = In band ringtone provided > + > + Opcode 0x93 - Last Voice Call Tag Number Callback notification > + > + Notification parameters: Number (string) > + > + Opcode 0x94 - Ring Indication notification > + > + Notification parameters: <none> > -- > 1.8.4 > \Lukasz -- To unsubscribe from this list: send the line "unsubscribe linux-bluetooth" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
