Hi Ryan, On Wed, Jun 25, 2014 at 4:23 PM, Ryan Press <ryan@xxxxxxxxxxx> wrote: > Hi Luiz, > > Yes it will repeat the scan every few seconds. > > I paired the device in the Gnome applet. In the bluetoothctl I could > see the pair and trust messages like so: > > [NEW] Device C5:8C:97:E6:9C:81 Arc Touch Mouse SE > [CHG] Device C5:8C:97:E6:9C:81 Connected: yes > [CHG] Device C5:8C:97:E6:9C:81 UUIDs: > 00001800-0000-1000-8000-00805f9b34fb > 00001801-0000-1000-8000-00805f9b34fb > 0000180a-0000-1000-8000-00805f9b34fb > 0000180f-0000-1000-8000-00805f9b34fb > 00001812-0000-1000-8000-00805f9b34fb > [CHG] Device C5:8C:97:E6:9C:81 Paired: yes > [CHG] Device C5:8C:97:E6:9C:81 Trusted: yes > [CHG] Device C5:8C:97:E6:9C:81 Modalias: usb:v045Ep07F3d0001 > > Thanks, > > Ryan > > > On Jun 25, 2014 12:08 AM, "Luiz Augusto von Dentz" <luiz.dentz@xxxxxxxxx> wrote: >> >> Hi Ryan, >> >> On Wed, Jun 25, 2014 at 5:27 AM, Ryan Press <ryan@xxxxxxxxxxx> wrote: >> > I have a Microsoft Arc mouse, Surface edition. This uses Bluetooth >> > Low Energy. Under dual boot Windows 8.1 I can connect this mouse, and >> > it will reconnect just fine if I turn the mouse off/on or Bluetooth >> > off/on. >> > >> > In Fedora rawhide I have Bluez 5.18-2. I can pair this mouse just >> > fine, and it will continue to work until I turn the mouse off/on or >> > turn the computer off/on. Then it won't reconnect automatically. If >> > I go into bluetoothctl I can connect it again and it will then work. >> > >> > I looked at bluetoothd and it seems to be doing the LE scan with: >> > bluetoothd[2356]: src/adapter.c:trigger_passive_scanning() >> > bluetoothd[2356]: src/adapter.c:passive_scanning_complete() status 0x00 >> > bluetoothd[2356]: src/adapter.c:discovering_callback() hci0 type 6 discovering 1 >> > >> > I look also at hcidump and I see: >> > < HCI Command: LE Set Random Address (0x08|0x0005) plen 6 >> > bdaddr 39:6D:E2:EC:17:37 >> >> HCI Event: Command Complete (0x0e) plen 4 >> > LE Set Random Address (0x08|0x0005) ncmd 1 >> > status 0x00 >> > < HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7 >> > type 0x01 (active) >> > interval 11.250ms window 11.250ms >> > own address: 0x01 (Random) policy: All >> >> HCI Event: Command Complete (0x0e) plen 4 >> > LE Set Scan Parameters (0x08|0x000b) ncmd 1 >> > status 0x00 >> > < HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 >> > value 0x01 (scanning enabled) >> > filter duplicates 0x01 (enabled) >> >> HCI Event: Command Complete (0x0e) plen 4 >> > LE Set Scan Enable (0x08|0x000c) ncmd 2 >> > status 0x00 >> > < HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 >> > value 0x00 (scanning disabled) >> > filter duplicates 0x00 (disabled) >> > >> > >> > It doesn't seem to be finding anything? Is there something else I should try? >> >> Does it continue to scan or it scan a single time and stops, and have >> you paired or just connect? Can you try with current master, we have applied a few patches for reconnection. -- Luiz Augusto von Dentz -- To unsubscribe from this list: send the line "unsubscribe linux-bluetooth" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
