On Mon, 9 Jun 2014 19:50:24 +0200 Marcel Holtmann <marcel@xxxxxxxxxxxx> wrote: > Hi Tedd, > > >>> I noticed that HCI_QUIRK_RESET_ON_CLOSE bit is used during stack initialization or device close exclusively. > >>> If the bit is set, HCI_RESET is sent to the device during device close but not during stack initialization and vice versa when it is not set. I just wonder if there is any reason for doing it? > >> > >> Bluetooth 1.0b and some Bluetooth 1.1 devices have not a clear defined behavior on HCI_Reset when it comes to the host transport. Only Bluetooth 1.1 cleared that HCI_Reset is not suppose to reset the transport. For example with USB. So you ended up seeing HCI_Reset, USB Reset, USB Disconnect, USB Connect endless cycles. > >> > >> A certain set of drivers are required to set this quirk. However eventually they have to do the HCI_Reset since otherwise we end up in funky states. Check drivers/bluetooth/ for devices that require not to send the HCI_Reset on init. > >> > >>> What do you recommend if HCI_RESET needs to be sent for both stack initialization case and device close? > >> > >> I have been thinking about this a while ago. Instead of using HCI_Reset we actually started to modify the kernel to clear out all its states when we are powering down the controller. A recent bluetooth-next kernel should just make sure we are no longer connectable and discoverable and also no longer advertising. > >> > >> We needed this for UART based devices where the transport has no clear indication that it is down. With USB devices this problem normally never happens since we are bringing down USB as well. > >> > >> Do you need something else? > > > > We are seeing an issue while turning on/off BT with inquiry, especially extended inquiry. If BT is turned off right after sending an extended inquiry, and next time when the BT is turned on the buffer is corrupted. We have seen this on Chromebook with 3.10 kernel. > > that is actually a good question for Johan, are we also canceling any connection attempts, remote name requests and ongoing inquiry transaction. We might need to verify that we really clean all of these that have baseband activity. > > > If the changes are made to recent version, I am not sure whether I can push the changes to chromebook tree. If it is not acceptable, then I need to come up with something else like sending HCI_RESET upon closing the device. > > So why are you getting a buffer corruption is kinda interesting. Since you will get a new HCI_Reset when you power Bluetooth back on. Not sure what makes the difference if it comes at the beginning or at the end or both times. > > Normally the HCI_Reset for UART based controllers is to ensure that all baseband resources are freed. That is what we are doing manually for each resources. Calling HCI_Reset is just the cheap way out ;) Here is what we found. After the host sends extended inquiry and it is turned off, the device is still in inquiry state and updates the USB FIFO with inquiry results. Once the BT is turned on, then host sends the HCI_RESET but it returns with inquiry results in USB FIFO. If the host sends HCI_RESET before BT off, at least the device state will be back to idle. > > The problem is that you can not know if sending HCI_Reset at the end is acceptable by all USB based devices. You need to quirk it. And right now it is just one quirk. We do not have separate quirks for opening HCI_Reset and closing HCI_Reset. That would need to be changed if we really need it. So far we did not. > Is it possible to have something like HCI_QUIRK_RESET_ON_INIT? Existing implementation will still be there and if a HW vendor wants this feature, they can set this up for init. > But just a heads up, this also forces changes into hci_uart driver and its ioctl interface if we change this. So there is a bit of work to be done to do this cleanly and without breaking other controllers. > > > Do you know which patches should I start to look at? > > I think that 3.14 kernel and later have this feature enabled. What I can tell is that we cancel connection attempts since I found a follow up patch there. For inquiry and remote name request, I do not know. > > Johan, did we ever checked this and in addition that we send a Discovery Stopped event as well. > > Regards > > Marcel > -- To unsubscribe from this list: send the line "unsubscribe linux-bluetooth" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
