Hey again,
This does look better now, right?
T: Bus=02 Lev=02 Prnt=02 Port=03 Cnt=03 Dev#= 11 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e031 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=EC55F9EADE09
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
but the two last lines still have no driver. Is this a problem?
Here is the output of hciconfig hci0 -a:
$ hciconfig hci0 -a
hci0: Type: BR/EDR Bus: USB
BD Address: EC:55:F9:EA:DE:09 ACL MTU: 1021:8 SCO MTU: 64:1
UP RUNNING PSCAN ISCAN
RX bytes:5947 acl:0 sco:0 events:198 errors:0
TX bytes:1986 acl:0 sco:0 commands:117 errors:0
Features: 0xff 0xff 0x8f 0xfe 0xdb 0xff 0x7b 0x87
Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3
Link policy: RSWITCH HOLD SNIFF PARK
Link mode: SLAVE ACCEPT
Name: 'abg4858n-lnx'
Class: 0x4a0100
Service Classes: Networking, Capturing, Telephony
Device Class: Computer, Uncategorized
HCI Version: 4.0 (0x6) Revision: 0x0
LMP Version: 4.0 (0x6) Subversion: 0x2118
Manufacturer: Broadcom Corporation (15)
Looks ok isn't it?
But I can't add any devices. When I search for devices VERY long, I can find one or two. But only devices which I can't pair with.
e.g. I never found my headset, altought it is in pairing mode when I start searching.
During search, hcidump -v shows only this:
> HCI Event: Inquiry Complete (0x01) plen 1
status 0x00
> HCI Event: Inquiry Complete (0x01) plen 1
status 0x00
> HCI Event: Inquiry Complete (0x01) plen 1
status 0x00
> HCI Event: Inquiry Complete (0x01) plen 1
status 0x00
> HCI Event: Inquiry Complete (0x01) plen 1
status 0x00
> HCI Event: Inquiry Complete (0x01) plen 1
status 0x00
> HCI Event: Inquiry Complete (0x01) plen 1
status 0x00
> HCI Event: Inquiry Complete (0x01) plen 1
status 0x00
> HCI Event: Inquiry Complete (0x01) plen 1
status 0x00
so no problem here too.
Any suggestions what I could try next? Anything which could give me informations whats going wrong here?
Ciao
Thilo
--
To unsubscribe from this list: send the line "unsubscribe linux-bluetooth" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
