From: Hsin-chen Chuang <chharry@xxxxxxxxxxxx> Automatically configure the altsetting for HCI_USER_CHANNEL when a SCO is connected. The motivation is to enable the HCI_USER_CHANNEL user to send out SCO data through USB Bluetooth chips, which is mainly used for bidirectional audio transfer (voice call). This was not capable because: - Per Bluetooth Core Spec v5, Vol 4, Part B, 2.1, the corresponding alternate setting should be set based on the air mode in order to transfer SCO data, but - The Linux Bluetooth HCI_USER_CHANNEL exposes the Bluetooth Host Controller Interface to the user space, which is something above the USB layer. The user space is not able to configure the USB alt while keeping the channel open. This patch intercepts the HCI_EV_SYNC_CONN_COMPLETE packets in btusb, extracts the air mode, and configures the alt setting in btusb. This patch is tested on ChromeOS devices. The USB Bluetooth models (CVSD, TRANS alt3 and alt6) could work without a customized kernel. Fixes: b16b327edb4d ("Bluetooth: btusb: add sysfs attribute to control USB alt setting") Signed-off-by: Hsin-chen Chuang <chharry@xxxxxxxxxxxx> --- Changes in v3: - Remove module parameter - Set Kconfig to default y if CHROME_PLATFORMS Changes in v2: - Give up tracking the SCO handles. Only configure the altsetting when SCO connected. - Put the change behind Kconfig/module parameter drivers/bluetooth/Kconfig | 11 ++++++++++ drivers/bluetooth/btusb.c | 43 +++++++++++++++++++++++++++++++++++++++ 2 files changed, 54 insertions(+) diff --git a/drivers/bluetooth/Kconfig b/drivers/bluetooth/Kconfig index 4ab32abf0f48..cdf7a5caa5c8 100644 --- a/drivers/bluetooth/Kconfig +++ b/drivers/bluetooth/Kconfig @@ -56,6 +56,17 @@ config BT_HCIBTUSB_POLL_SYNC Say Y here to enable USB poll_sync for Bluetooth USB devices by default. +config BT_HCIBTUSB_AUTO_SET_ISOC_ALT + bool "Auto set isoc_altsetting for HCI_USER_CHANNEL when SCO connected" + depends on BT_HCIBTUSB + default y if CHROME_PLATFORMS + help + Say Y here to enable auto set isoc_altsetting for HCI_USER_CHANNEL + when SCO connected + + When enabled, btusb intercepts the HCI_EV_SYNC_CONN_COMPLETE packets + and configures isoc_altsetting automatically for HCI_USER_CHANNEL. + config BT_HCIBTUSB_BCM bool "Broadcom protocol support" depends on BT_HCIBTUSB diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c index de3fa725d210..2642d2ca885f 100644 --- a/drivers/bluetooth/btusb.c +++ b/drivers/bluetooth/btusb.c @@ -34,6 +34,8 @@ static bool force_scofix; static bool enable_autosuspend = IS_ENABLED(CONFIG_BT_HCIBTUSB_AUTOSUSPEND); static bool enable_poll_sync = IS_ENABLED(CONFIG_BT_HCIBTUSB_POLL_SYNC); static bool reset = true; +static bool auto_set_isoc_alt = + IS_ENABLED(CONFIG_BT_HCIBTUSB_AUTO_SET_ISOC_ALT); static struct usb_driver btusb_driver; @@ -1113,6 +1115,42 @@ static inline void btusb_free_frags(struct btusb_data *data) spin_unlock_irqrestore(&data->rxlock, flags); } +static void btusb_sco_connected(struct btusb_data *data, struct sk_buff *skb) +{ + struct hci_event_hdr *hdr = (void *) skb->data; + struct hci_ev_sync_conn_complete *ev = + (void *) skb->data + sizeof(*hdr); + struct hci_dev *hdev = data->hdev; + unsigned int notify_air_mode; + + if (hci_skb_pkt_type(skb) != HCI_EVENT_PKT) + return; + + if (skb->len < sizeof(*hdr) || hdr->evt != HCI_EV_SYNC_CONN_COMPLETE) + return; + + if (skb->len != sizeof(*hdr) + sizeof(*ev) || ev->status) + return; + + switch (ev->air_mode) { + case BT_CODEC_CVSD: + notify_air_mode = HCI_NOTIFY_ENABLE_SCO_CVSD; + break; + + case BT_CODEC_TRANSPARENT: + notify_air_mode = HCI_NOTIFY_ENABLE_SCO_TRANSP; + break; + + default: + return; + } + + bt_dev_info(hdev, "enabling SCO with air mode %u", ev->air_mode); + data->sco_num = 1; + data->air_mode = notify_air_mode; + schedule_work(&data->work); +} + static int btusb_recv_event(struct btusb_data *data, struct sk_buff *skb) { if (data->intr_interval) { @@ -1120,6 +1158,11 @@ static int btusb_recv_event(struct btusb_data *data, struct sk_buff *skb) schedule_delayed_work(&data->rx_work, 0); } + /* Configure altsetting for HCI_USER_CHANNEL on SCO connected */ + if (auto_set_isoc_alt && + hci_dev_test_flag(data->hdev, HCI_USER_CHANNEL)) + btusb_sco_connected(data, skb); + return data->recv_event(data->hdev, skb); } -- 2.48.1.658.g4767266eb4-goog