Add a PMU node for the WCN6750 module present on the qcs6490-rb3gen board
and use the power sequencer for the same.
Signed-off-by: Janaki Ramaiah Thota <quic_janathot@xxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts | 174 ++++++++++++++++++-
drivers/bluetooth/hci_qca.c | 2 +-
drivers/power/sequencing/pwrseq-qcom-wcn.c | 22 +++
3 files changed, 196 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
index 27695bd54220..6807bf347241 100644
--- a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
+++ b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
@@ -1,6 +1,6 @@
// SPDX-License-Identifier: BSD-3-Clause
/*
- * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ * Copyright (c) 2023-2024 Qualcomm Innovation Center, Inc. All rights reserved.
*/
/dts-v1/;
@@ -32,7 +32,9 @@
chassis-type = "embedded";
aliases {
+ bluetooth0 = &bluetooth;
serial0 = &uart5;
+ serial1 = &uart7;
};
chosen {
@@ -217,6 +219,64 @@
regulator-min-microvolt = <3700000>;
regulator-max-microvolt = <3700000>;
};
+
+ wcn6750-pmu {
+ compatible = "qcom,wcn6750-pmu";
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_en>, <&sw_ctrl>;
+ vddaon-supply = <&vreg_s7b_0p972>;
+ vddasd-supply = <&vreg_l11c_2p8>;
+ vddpmu-supply = <&vreg_s7b_0p972>;
+ vddrfa0p8-supply = <&vreg_s7b_0p972>;
+ vddrfa1p2-supply = <&vreg_s8b_1p272>;
+ vddrfa1p7-supply = <&vreg_s1b_1p872>;
+ vddrfa2p2-supply = <&vreg_s1c_2p19>;
+
+ bt-enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>;
+ wlan-enable-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>;
+
+ regulators {
+ vreg_pmu_rfa_cmn: ldo0 {
+ regulator-name = "vreg_pmu_rfa_cmn";
+ };
+
+ vreg_pmu_aon_0p59: ldo1 {
+ regulator-name = "vreg_pmu_aon_0p59";
+ };
+
+ vreg_pmu_wlcx_0p8: ldo2 {
+ regulator-name = "vreg_pmu_wlcx_0p8";
+ };
+
+ vreg_pmu_wlmx_0p85: ldo3 {
+ regulator-name = "vreg_pmu_wlmx_0p85";
+ };
+
+ vreg_pmu_btcmx_0p85: ldo4 {
+ regulator-name = "vreg_pmu_btcmx_0p85";
+ };
+
+ vreg_pmu_rfa_0p8: ldo5 {
+ regulator-name = "vreg_pmu_rfa_0p8";
+ };
+
+ vreg_pmu_rfa_1p2: ldo6 {
+ regulator-name = "vreg_pmu_rfa_1p2";
+ };
+
+ vreg_pmu_rfa_1p7: ldo7 {
+ regulator-name = "vreg_pmu_rfa_1p7";
+ };
+
+ vreg_pmu_pcie_0p9: ldo8 {
+ regulator-name = "vreg_pmu_pcie_0p9";
+ };
+
+ vreg_pmu_pcie_1p8: ldo9 {
+ regulator-name = "vreg_pmu_pcie_1p8";
+ };
+ };
+ };
};
&apps_rsc {
@@ -758,6 +818,39 @@
status = "okay";
};
+&qup_uart7_cts {
+ /*
+ * Configure a bias-bus-hold on CTS to lower power
+ * usage when Bluetooth is turned off. Bus hold will
+ * maintain a low power state regardless of whether
+ * the Bluetooth module drives the pin in either
+ * direction or leaves the pin fully unpowered.
+ */
+ bias-bus-hold;
+};
+
+&qup_uart7_rts {
+ /* We'll drive RTS, so no pull */
+ drive-strength = <2>;
+ bias-disable;
+};
+
+&qup_uart7_rx {
+ /*
+ * Configure a pull-up on RX. This is needed to avoid
+ * garbage data when the TX pin of the Bluetooth module is
+ * in tri-state (module powered off or not driving the
+ * signal yet).
+ */
+ bias-pull-up;
+};
+
+&qup_uart7_tx {
+ /* We'll drive TX, so no pull */
+ drive-strength = <2>;
+ bias-disable;
+};
+
&qupv3_id_0 {
status = "okay";
};
@@ -801,12 +894,91 @@
&tlmm {
gpio-reserved-ranges = <32 2>, /* ADSP */
<48 4>; /* NFC */
+ bt_en: bt-en-state {
+ pins = "gpio85";
+ function = "gpio";
+ output-low;
+ bias-disable;
+ };
+
+ qup_uart7_sleep_cts: qup-uart7-sleep-cts-state {
+ pins = "gpio28";
+ function = "gpio";
+ /*
+ * Configure a bias-bus-hold on CTS to lower power
+ * usage when Bluetooth is turned off. Bus hold will
+ * maintain a low power state regardless of whether
+ * the Bluetooth module drives the pin in either
+ * direction or leaves the pin fully unpowered.
+ */
+ bias-bus-hold;
+ };
+
+ qup_uart7_sleep_rts: qup-uart7-sleep-rts-state {
+ pins = "gpio29";
+ function = "gpio";
+ /*
+ * Configure pull-down on RTS. As RTS is active low
+ * signal, pull it low to indicate the BT SoC that it
+ * can wakeup the system anytime from suspend state by
+ * pulling RX low (by sending wakeup bytes).
+ */
+ bias-pull-down;
+ };
+
+ qup_uart7_sleep_rx: qup-uart7-sleep-rx-state {
+ pins = "gpio31";
+ function = "gpio";
+ /*
+ * Configure a pull-up on RX. This is needed to avoid
+ * garbage data when the TX pin of the Bluetooth module
+ * is floating which may cause spurious wakeups.
+ */
+ bias-pull-up;
+ };
+
+ qup_uart7_sleep_tx: qup-uart7-sleep-tx-state {
+ pins = "gpio30";
+ function = "gpio";
+ /*
+ * Configure pull-up on TX when it isn't actively driven
+ * to prevent BT SoC from receiving garbage during sleep.
+ */
+ bias-pull-up;
+ };
+
+ sw_ctrl: sw-ctrl-state {
+ pins = "gpio86";
+ function = "gpio";
+ bias-pull-down;
+ };
};
&uart5 {
status = "okay";
};
+&uart7 {
+ status = "okay";
+ /delete-property/interrupts;
+ interrupts-extended = <&intc GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>,
+ <&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-1 = <&qup_uart7_sleep_cts>, <&qup_uart7_sleep_rts>,
+ <&qup_uart7_sleep_tx>, <&qup_uart7_sleep_rx>;
+
+ bluetooth: bluetooth {
+ compatible = "qcom,wcn6750-bt";
+ vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+ vddaon-supply = <&vreg_pmu_aon_0p59>;
+ vddbtcmx-supply = <&vreg_pmu_btcmx_0p85>;
+ vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+ vddrfa1p7-supply = <&vreg_pmu_rfa_1p7>;
+ vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+ max-speed = <3200000>;
+ };
+};
+
&usb_1 {
status = "okay";
};
diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
index 37129e6cb0eb..fbf8840fa534 100644
--- a/drivers/bluetooth/hci_qca.c
+++ b/drivers/bluetooth/hci_qca.c
@@ -2346,6 +2346,7 @@ static int qca_serdev_probe(struct serdev_device *serdev)
switch (qcadev->btsoc_type) {
case QCA_WCN6855:
case QCA_WCN7850:
+ case QCA_WCN6750:
if (!device_property_present(&serdev->dev, "enable-gpios")) {
/*
* Backward compatibility with old DT sources. If the
@@ -2365,7 +2366,6 @@ static int qca_serdev_probe(struct serdev_device *serdev)
case QCA_WCN3990:
case QCA_WCN3991:
case QCA_WCN3998:
- case QCA_WCN6750:
qcadev->bt_power->dev = &serdev->dev;
err = qca_init_regulators(qcadev->bt_power, data->vregs,
data->num_vregs);
diff --git a/drivers/power/sequencing/pwrseq-qcom-wcn.c b/drivers/power/sequencing/pwrseq-qcom-wcn.c
index 682a9beac69e..e38da79f0ada 100644
--- a/drivers/power/sequencing/pwrseq-qcom-wcn.c
+++ b/drivers/power/sequencing/pwrseq-qcom-wcn.c
@@ -293,6 +293,24 @@ static const struct pwrseq_qcom_wcn_pdata pwrseq_wcn6855_of_data = {
.targets = pwrseq_qcom_wcn6855_targets,
};
+static const char *const pwrseq_wcn6750_vregs[] = {
+ "vddaon",
+ "vddasd",
+ "vddpmu",
+ "vddrfa0p8",
+ "vddrfa1p2",
+ "vddrfa1p7",
+ "vddrfa2p2",
+};
+
+static const struct pwrseq_qcom_wcn_pdata pwrseq_wcn6750_of_data = {
+ .vregs = pwrseq_wcn6750_vregs,
+ .num_vregs = ARRAY_SIZE(pwrseq_wcn6750_vregs),
+ .pwup_delay_ms = 50,
+ .gpio_enable_delay_ms = 5,
+ .targets = pwrseq_qcom_wcn_targets,
+};
+
static const char *const pwrseq_wcn7850_vregs[] = {
"vdd",
"vddio",
@@ -431,6 +449,10 @@ static const struct of_device_id pwrseq_qcom_wcn_of_match[] = {
.compatible = "qcom,wcn7850-pmu",
.data = &pwrseq_wcn7850_of_data,
},
+ {
+ .compatible = "qcom,wcn6750-pmu",
+ .data = &pwrseq_wcn6750_of_data,
+ },
{ }
};
MODULE_DEVICE_TABLE(of, pwrseq_qcom_wcn_of_match);
--
