The RTL8852BE-VT supports USB alternate setting 6.
However, its descriptor does not report this capability to the host.
Therefore, a quirk is needed to bypass the RTL8852BE-VT's descriptor
and allow it to use USB ALT 6 directly.
The btmon log below shows the case that WBS with the USB alternate
setting 6.
< HCI Command: Enhanced.. (0x01|0x003d) plen 59 #2123 [hci0] 82.701813
Handle: 1 Address: 78:A7:EB:4C:53:4D (1MORE)
Transmit bandwidth: 8000
Receive bandwidth: 8000
Max latency: 13
Packet type: 0x0380
3-EV3 may not be used
2-EV5 may not be used
3-EV5 may not be used
Retransmission effort: Optimize for link quality (0x02)
< ACL Data TX: Handle 1 flags 0x00 dlen 22 #2124 [hci0] 82.701825
Channel: 65 len 18 [PSM 3 mode Basic (0x00)] {chan 1}
RFCOMM: Unnumbered Info with Header Check (UIH) (0xef)
Address: 0x0b cr 1 dlci 0x02
Control: 0xef poll/final 0
Length: 14
FCS: 0x9a
0d 0a 2b 43 49 45 56 3a 20 32 2c 31 0d 0a 9a ..+CIEV: 2,1..>
> HCI Event: Command Status (0x0f) plen 4 #2125 [hci0] 82.703812
Enhanced Setup Synchronous Connection (0x01|0x003d) ncmd 2
Status: Success (0x00)
> HCI Event: Number of Complete.. (0x13) plen 5 #2126 [hci0] 82.710834
Num handles: 1
Handle: 1 Address: 78:A7:EB:4C:53:4D (1MORE)
Count: 1
#2124: len 22 (19 Kb/s)
Latency: 9 msec (3-56 msec ~13 msec)
Channel: 65 [PSM 3 mode Basic (0x00)] {chan 1}
Channel Latency: 9 msec (4-27 msec ~15 msec)
> HCI Event: Synchronous Conne.. (0x2c) plen 17 #2127 [hci0] 82.741840
Status: Success (0x00)
Handle: 2
Address: 78:A7:EB:4C:53:4D (1MORE)
Link type: eSCO (0x02)
Transmission interval: 0x0c
Retransmission window: 0x04
RX packet length: 60
TX packet length: 60
Air mode: Transparent (0x03)
@ RAW Open: btmon (privileged) version 2.22 {0x0002} 82.742580
@ RAW Close: btmon {0x0002} 82.742594
> SCO Data RX: Handle 2 flags 0x00 dlen 60 #2128 [hci0] 82.764812
< ACL Data TX: Handle 1 flags 0x00 dlen 19 #2129 [hci0] 82.764994
Channel: 65 len 15 [PSM 3 mode Basic (0x00)] {chan 1}
RFCOMM: Unnumbered Info with Header Check (UIH) (0xef)
Address: 0x0b cr 1 dlci 0x02
Control: 0xef poll/final 0
Length: 11
FCS: 0x9a
0d 0a 2b 56 47 53 3a 20 36 0d 0a 9a ..+VGS: 6... >
> HCI Event: Max Slots Change (0x1b) plen 3 #2130 [hci0] 82.765814
Handle: 1 Address: 78:A7:EB:4C:53:4D (1MORE)
Max slots: 1
< SCO Data TX: Handle 2 flags 0x00 dlen 60 #2131 [hci0] 82.765897
> HCI Event: Number of Complete.. (0x13) plen 5 #2132 [hci0] 82.771855
Num handles: 1
Handle: 1 Address: 78:A7:EB:4C:53:4D (1MORE)
Count: 1
#2129: len 19 (25 Kb/s)
Latency: 6 msec (3-56 msec ~10 msec)
Channel: 65 [PSM 3 mode Basic (0x00)] {chan 1}
Channel Latency: 6 msec (4-27 msec ~11 msec)
< SCO Data TX: Handle 2 flags 0x00 dlen 60 #2133 [hci0] 82.773344
> SCO Data RX: Handle 2 flags 0x00 dlen 60 #2134 [hci0] 82.774836
> SCO Data RX: Handle 2 flags 0x00 dlen 60 #2135 [hci0] 82.774839
> SCO Data RX: Handle 2 flags 0x00 dlen 60 #2136 [hci0] 82.784840
< SCO Data TX: Handle 2 flags 0x00 dlen 60 #2137 [hci0] 82.787175
< SCO Data TX: Handle 2 flags 0x00 dlen 60 #2138 [hci0] 82.788282
> SCO Data RX: Handle 2 flags 0x00 dlen 60 #2139 [hci0] 82.794812
< SCO Data TX: Handle 2 flags 0x00 dlen 60 #2140 [hci0] 82.795797
> SCO Data RX: Handle 2 flags 0x00 dlen 60 #2141 [hci0] 82.804838
> SCO Data RX: Handle 2 flags 0x00 dlen 60 #2142 [hci0] 82.804840
< SCO Data TX: Handle 2 flags 0x00 dlen 60 #2143 [hci0] 82.808554
Signed-off-by: Alex Lu <alex_lu@xxxxxxxxxxxxxx>
Signed-off-by: Hilda Wu <hildawu@xxxxxxxxxxx>
---
Change:
V3: Fixed SubjectPrefix, use quirk instead of btrealtek_*_flag()
v2: Use btusb_find_altsetting replace duplicating logic, add tested log.
---
---
drivers/bluetooth/btrtl.c | 3 ++
drivers/bluetooth/btrtl.h | 1 +
drivers/bluetooth/btusb.c | 86 ++++++++++++++++++++++++++++++---------
3 files changed, 70 insertions(+), 20 deletions(-)
diff --git a/drivers/bluetooth/btrtl.c b/drivers/bluetooth/btrtl.c
index 83025f457ca0..7efd733f9e84 100644
--- a/drivers/bluetooth/btrtl.c
+++ b/drivers/bluetooth/btrtl.c
@@ -1312,6 +1312,9 @@ void btrtl_set_quirks(struct hci_dev *hdev, struct btrtl_device_info *btrtl_dev)
btrtl_dev->project_id == CHIP_ID_8852C)
set_bit(HCI_QUIRK_USE_MSFT_EXT_ADDRESS_FILTER, &hdev->quirks);
+ if (btrtl_dev->project_id == CHIP_ID_8852BT)
+ btrealtek_set_flag(hdev, REALTEK_ALT6_FORCE);
+
hci_set_aosp_capable(hdev);
break;
default:
diff --git a/drivers/bluetooth/btrtl.h b/drivers/bluetooth/btrtl.h
index a2d9d34f9fb0..ffec2fca88ec 100644
--- a/drivers/bluetooth/btrtl.h
+++ b/drivers/bluetooth/btrtl.h
@@ -105,6 +105,7 @@ struct rtl_vendor_cmd {
enum {
REALTEK_ALT6_CONTINUOUS_TX_CHIP,
+ REALTEK_ALT6_FORCE,
__REALTEK_NUM_FLAGS,
};
diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index 279fe6c115fa..6acdff772ca5 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -814,6 +814,8 @@ struct qca_dump_info {
#define BTUSB_USE_ALT3_FOR_WBS 15
#define BTUSB_ALT6_CONTINUOUS_TX 16
#define BTUSB_HW_SSR_ACTIVE 17
+#define BTUSB_ALT6_QUIRK 18
+#define BTUSB_ISOC_ALT_CHANGED 19
struct btusb_data {
struct hci_dev *hdev;
@@ -866,6 +868,7 @@ struct btusb_data {
unsigned int air_mode;
bool usb_alt6_packet_flow;
int isoc_altsetting;
+ u16 isoc_mps;
int suspend_count;
int (*recv_event)(struct hci_dev *hdev, struct sk_buff *skb);
@@ -2140,16 +2143,58 @@ static void btusb_notify(struct hci_dev *hdev, unsigned int evt)
}
}
+static struct usb_host_interface *btusb_find_altsetting(struct btusb_data *data,
+ int alt)
+{
+ struct usb_interface *intf = data->isoc;
+ int i;
+
+ BT_DBG("Looking for Alt no :%d", alt);
+
+ if (!intf)
+ return NULL;
+
+ for (i = 0; i < intf->num_altsetting; i++) {
+ if (intf->altsetting[i].desc.bAlternateSetting == alt)
+ return &intf->altsetting[i];
+ }
+
+ return NULL;
+}
+
static inline int __set_isoc_interface(struct hci_dev *hdev, int altsetting)
{
struct btusb_data *data = hci_get_drvdata(hdev);
struct usb_interface *intf = data->isoc;
struct usb_endpoint_descriptor *ep_desc;
+ struct usb_host_interface *alt;
int i, err;
if (!data->isoc)
return -ENODEV;
+ /* For some Realtek chips, they actually have the altsetting 6, but its
+ * altsetting descriptor is not exposed. We can activate altsetting 6 by
+ * replacing the altsetting 5.
+ */
+ if (altsetting == 6 && !btusb_find_altsetting(data, 6) &&
+ test_bit(BTUSB_ALT6_QUIRK, &data->flags)) {
+ alt = btusb_find_altsetting(data, 5);
+ if (alt) {
+ data->isoc_mps = 49;
+ for (i = 0; i < alt->desc.bNumEndpoints; i++) {
+ ep_desc = &alt->endpoint[i].desc;
+ if (!usb_endpoint_xfer_isoc(ep_desc))
+ continue;
+ data->isoc_mps =
+ le16_to_cpu(ep_desc->wMaxPacketSize);
+ ep_desc->wMaxPacketSize = cpu_to_le16(63);
+ }
+ alt->desc.bAlternateSetting = 6;
+ set_bit(BTUSB_ISOC_ALT_CHANGED, &data->flags);
+ }
+ }
+
err = usb_set_interface(data->udev, data->isoc_ifnum, altsetting);
if (err < 0) {
bt_dev_err(hdev, "setting interface failed (%d)", -err);
@@ -2161,6 +2206,22 @@ static inline int __set_isoc_interface(struct hci_dev *hdev, int altsetting)
data->isoc_tx_ep = NULL;
data->isoc_rx_ep = NULL;
+ /* Recover alt 5 desc if alt 0 is set. */
+ if (!altsetting && test_bit(BTUSB_ISOC_ALT_CHANGED, &data->flags)) {
+ alt = btusb_find_altsetting(data, 6);
+ if (alt) {
+ for (i = 0; i < alt->desc.bNumEndpoints; i++) {
+ ep_desc = &alt->endpoint[i].desc;
+ if (!usb_endpoint_xfer_isoc(ep_desc))
+ continue;
+ ep_desc->wMaxPacketSize =
+ cpu_to_le16(data->isoc_mps);
+ }
+ alt->desc.bAlternateSetting = 5;
+ clear_bit(BTUSB_ISOC_ALT_CHANGED, &data->flags);
+ }
+ }
+
for (i = 0; i < intf->cur_altsetting->desc.bNumEndpoints; i++) {
ep_desc = &intf->cur_altsetting->endpoint[i].desc;
@@ -2223,25 +2284,6 @@ static int btusb_switch_alt_setting(struct hci_dev *hdev, int new_alts)
return 0;
}
-static struct usb_host_interface *btusb_find_altsetting(struct btusb_data *data,
- int alt)
-{
- struct usb_interface *intf = data->isoc;
- int i;
-
- BT_DBG("Looking for Alt no :%d", alt);
-
- if (!intf)
- return NULL;
-
- for (i = 0; i < intf->num_altsetting; i++) {
- if (intf->altsetting[i].desc.bAlternateSetting == alt)
- return &intf->altsetting[i];
- }
-
- return NULL;
-}
-
static void btusb_work(struct work_struct *work)
{
struct btusb_data *data = container_of(work, struct btusb_data, work);
@@ -2279,7 +2321,8 @@ static void btusb_work(struct work_struct *work)
* MTU >= 3 (packets) * 25 (size) - 3 (headers) = 72
* see also Core spec 5, vol 4, B 2.1.1 & Table 2.1.
*/
- if (btusb_find_altsetting(data, 6))
+ if (btusb_find_altsetting(data, 6) ||
+ test_bit(BTUSB_ALT6_QUIRK, &data->flags))
new_alts = 6;
else if (btusb_find_altsetting(data, 3) &&
hdev->sco_mtu >= 72 &&
@@ -2611,6 +2654,9 @@ static int btusb_setup_realtek(struct hci_dev *hdev)
if (btrealtek_test_flag(data->hdev, REALTEK_ALT6_CONTINUOUS_TX_CHIP))
set_bit(BTUSB_ALT6_CONTINUOUS_TX, &data->flags);
+ if (btrealtek_test_flag(data->hdev, REALTEK_ALT6_FORCE))
+ set_bit(BTUSB_ALT6_QUIRK, &data->flags);
+
return ret;
}
--
2.34.1
