Their devices claim to support the erroneous data reporting, but don't
actually support the required commands. So blacklist them and add a
quirk.
< HCI Command: Read Default Erroneous Data Reporting (0x03|0x005a) plen 0
> HCI Event: Command Status (0x0f) plen 4
Read Default Erroneous Data Reporting (0x03|0x005a) ncmd 1
Status: Unknown HCI Command (0x01)
T: Bus=02 Lev=02 Prnt=08 Port=02 Cnt=01 Dev#= 10 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=10d7 ProdID=b012 Rev=88.91
S: Manufacturer=Actions
S: Product=general adapter
S: SerialNumber=ACTIONS1234
C:* #Ifs= 2 Cfg#= 1 Atr=c0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=01(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=01(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=01(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=01(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=01(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=01(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Marcel Holtmann <marcel@xxxxxxxxxxxx>
---
drivers/bluetooth/btusb.c | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index 2ad4efdd9e40..afd2f08ffe30 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -64,6 +64,7 @@ static struct usb_driver btusb_driver;
#define BTUSB_INTEL_BROKEN_SHUTDOWN_LED BIT(24)
#define BTUSB_INTEL_BROKEN_INITIAL_NCMD BIT(25)
#define BTUSB_INTEL_NO_WBS_SUPPORT BIT(26)
+#define BTUSB_ACTIONS_SEMI BIT(27)
static const struct usb_device_id btusb_table[] = {
/* Generic Bluetooth USB device */
@@ -677,6 +678,9 @@ static const struct usb_device_id blacklist_table[] = {
{ USB_DEVICE(0x0cb5, 0xc547), .driver_info = BTUSB_REALTEK |
BTUSB_WIDEBAND_SPEECH },
+ /* Actions Semiconductor ATS2851 based devices */
+ { USB_DEVICE(0x10d7, 0xb012), .driver_info = BTUSB_ACTIONS_SEMI },
+
/* Silicon Wave based devices */
{ USB_DEVICE(0x0c10, 0x0000), .driver_info = BTUSB_SWAVE },
@@ -4098,6 +4102,11 @@ static int btusb_probe(struct usb_interface *intf,
set_bit(BTUSB_USE_ALT3_FOR_WBS, &data->flags);
}
+ if (id->driver_info & BTUSB_ACTIONS_SEMI) {
+ /* Support is advertised, but not implemented */
+ set_bit(HCI_QUIRK_BROKEN_ERR_DATA_REPORTING, &hdev->quirks);
+ }
+
if (!reset)
set_bit(HCI_QUIRK_RESET_ON_CLOSE, &hdev->quirks);
--
2.38.1
