Switch to use _configure_null_blk so that built-in null_blk can be
supported, which implies not using the default nullb0 device.
Signed-off-by: Christoph Hellwig <hch@xxxxxx>
---
tests/block/024 | 21 +++++++++++----------
1 file changed, 11 insertions(+), 10 deletions(-)
diff --git a/tests/block/024 b/tests/block/024
index 6808db0..2a7c934 100755
--- a/tests/block/024
+++ b/tests/block/024
@@ -17,13 +17,13 @@ requires() {
}
init_times() {
- init_read_ms="$(awk '{ print $4 }' /sys/block/nullb0/stat)"
- init_write_ms="$(awk '{ print $8 }' /sys/block/nullb0/stat)"
+ init_read_ms="$(awk '{ print $4 }' /sys/block/nullb1/stat)"
+ init_write_ms="$(awk '{ print $8 }' /sys/block/nullb1/stat)"
}
show_times() {
- read_ms="$(awk '{ print $4 }' /sys/block/nullb0/stat)"
- write_ms="$(awk '{ print $8 }' /sys/block/nullb0/stat)"
+ read_ms="$(awk '{ print $4 }' /sys/block/nullb1/stat)"
+ write_ms="$(awk '{ print $8 }' /sys/block/nullb1/stat)"
# Print rounded to the nearest second
printf 'read %d s\n' $(((read_ms - init_read_ms + 500) / 1000))
@@ -37,7 +37,8 @@ test() {
# The maximum value for CONFIG_HZ is 1000. I.e., a tick is one
# millisecond. So, make each I/O take half a millisecond.
- if ! _init_null_blk irqmode=2 completion_nsec=500000; then
+ if ! _configure_null_blk nullb1 irqmode=2 completion_nsec=500000 \
+ power=1; then
return 1
fi
@@ -46,16 +47,16 @@ test() {
# 1500 * 0.5 ms is 0.75 seconds, allowing for some overhead so
# that it rounds to one second.
- dd if=/dev/nullb0 of=/dev/null bs=4096 iflag=direct count=1500 status=none
+ dd if=/dev/nullb1 of=/dev/null bs=4096 iflag=direct count=1500 status=none
show_times
- dd if=/dev/zero of=/dev/nullb0 bs=4096 oflag=direct count=1500 status=none
+ dd if=/dev/zero of=/dev/nullb1 bs=4096 oflag=direct count=1500 status=none
show_times
# 1800 * 0.5 ms is 0.9 seconds.
- dd if=/dev/nullb0 of=/dev/null bs=4096 iflag=direct count=1500 status=none &
- dd if=/dev/zero of=/dev/nullb0 bs=4096 oflag=direct count=1800 status=none &
- dd if=/dev/zero of=/dev/nullb0 bs=4096 oflag=direct count=1800 status=none &
+ dd if=/dev/nullb1 of=/dev/null bs=4096 iflag=direct count=1500 status=none &
+ dd if=/dev/zero of=/dev/nullb1 bs=4096 oflag=direct count=1800 status=none &
+ dd if=/dev/zero of=/dev/nullb1 bs=4096 oflag=direct count=1800 status=none &
wait
show_times
--
2.30.2
