On 19/05/2021 04:55, Damien Le Moal wrote:
> Zone append BIOs (REQ_OP_ZONE_APPEND) always specify the start sector
> of the zone to be written instead of the actual sector location to
> write. The write location is determined by the device and returned to
> the host upon completion of the operation. This interface, while simple
> and efficient for writing into sequential zones of a zoned block
> device, is incompatible with the use of sector values to calculate a
> cypher block IV. All data written in a zone end up using the same IV
> values corresponding to the first sectors of the zone, but read
> operation will specify any sector within the zone resulting in an IV
> mismatch between encryption and decryption.
>
> To solve this problem, report to DM core that zone append operations are
> not supported. This result in the zone append operations being emulated
> using regular write operations.
Yes, I think this is definitive better approach and it does not need
to fiddle with dm-crypt crypto, thanks.
Just one comment below:
>
> Reported-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@xxxxxxx>
> Signed-off-by: Damien Le Moal <damien.lemoal@xxxxxxx>
> ---
> drivers/md/dm-crypt.c | 24 +++++++++++++++++++-----
> 1 file changed, 19 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/md/dm-crypt.c b/drivers/md/dm-crypt.c
> index f410ceee51d7..44339823371c 100644
> --- a/drivers/md/dm-crypt.c
> +++ b/drivers/md/dm-crypt.c
> @@ -3280,14 +3280,28 @@ static int crypt_ctr(struct dm_target *ti, unsigned int argc, char **argv)
> }
> cc->start = tmpll;
>
> - /*
> - * For zoned block devices, we need to preserve the issuer write
> - * ordering. To do so, disable write workqueues and force inline
> - * encryption completion.
> - */
> if (bdev_is_zoned(cc->dev->bdev)) {
> + /*
> + * For zoned block devices, we need to preserve the issuer write
> + * ordering. To do so, disable write workqueues and force inline
> + * encryption completion.
> + */
> set_bit(DM_CRYPT_NO_WRITE_WORKQUEUE, &cc->flags);
> set_bit(DM_CRYPT_WRITE_INLINE, &cc->flags);
> +
> + /*
> + * All zone append writes to a zone of a zoned block device will
> + * have the same BIO sector, the start of the zone. When the
> + * cypher IV mode uses sector values, all data targeting a
> + * zone will be encrypted using the first sector numbers of the
> + * zone. This will not result in write errors but will
> + * cause most reads to fail as reads will use the sector values
> + * for the actual data locations, resulting in IV mismatch.
> + * To avoid this problem, ask DM core to emulate zone append
> + * operations with regular writes.
> + */
> + DMWARN("Zone append operations will be emulated");
Do we really want to fill log with these?
(I know it is not a good example in this context - but during online reencryption,
dm-crypt table segments are continuously reloaded and because the message is in in table constructor,
it will flood the syslog with repeated message.)
Maybe move it to debug or remove it completely?
What would be nice to have some zoned info extension to lsblk so we can investigate
storage stack over zoned device (if there is some sysfs knob to detect it, it should be trivial)...
Thanks,
Milan
> + ti->emulate_zone_append = true;
> }
>
> if (crypt_integrity_aead(cc) || cc->integrity_iv_size) {
>
