Re: LKFT: arm x15: mmc1: cache flush error -110

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Uffe,

On 06/03/20 4:44 pm, Ulf Hansson wrote:
> [...]
> 
>>>>>>>>>>>
>>>>>>>>>>> Actually we always use R1B with CMD6 as per spec.
>>>>>>>>>> I fully agree that R1B is preferable, but it's not against the
>>>>>>>>>> spec to
>>>>>>>>>> send CMD13 to poll for busy.
>>>>>>>>>>
>>>>>>>>>> Moreover, we need to cope with the scenario when the host has
>>>>>>>>>> specified a maximum timeout that isn't sufficiently long enough for
>>>>>>>>>> the requested operation. Do you have another proposal for how to
>>>>>>>>>> manage this, but disabling MMC_RSP_BUSY?
>>>>>>>>>>
>>>>>>>>>> Let's assume you driver would get a R1B for the CMD6 (we force it),
>>>>>>>>>> then what timeout would the driver be using if we would set
>>>>>>>>>> cmd.busy_timeout to 30ms?
>>>>>>>>>>
>>>> Sorry didn't understood clearly. Are you asking with 30s timeout, whats
>>>> the data timeout counter used?
>>> Yes. It seems like it will pick the maximum, which is 11s?
>> yes
> 
> Okay, thanks!
> 
>>>
>>>> Because of above mentioned issue on our host where CMD interrupt happens
>>>> after busy state, poll for busy returns right away as not busy.
>>> I see.
>>>
>>>> So issuing CMD13 after CMD6-R1 followed by busy poll should be working.
>>>> But weird that with small delay of 1ms or debug print before CMD13 it
>>>> doesn't timeout and works all the time.
>>> I have digested the information you provided in these emails. Let me
>>> summarize it, to see if I have understood correctly.
>>>
>>> 1.
>>> Your controller can't distinguish between R1 and R1B because of a
>>> limitation in the HW. So, in both cases you need to wait for the card
>>> to stop signal busy, before the controller can give an IRQ to notify
>>> that the R1 response has been received. Correct?
>>>
>>> In this context, I am wondering if sdhci_send_command(), really
>>> conforms to these requirements. For example, depending on if the CMD6
>>> has MMC_RSP_BUSY or not, it may pick either SDHCI_CMD_RESP_SHORT or
>>> SDHCI_CMD_RESP_SHORT_BUSY.
>>>
>>> Does this work as expected for your case?
>> Design team re-verified internally and bug where HW waits for busy state
>> before IRQ is only for R1B and R1 is spec compliant.
>>
>> So, with R1, CMD complete is generated after response received.
> 
> Okay.
> 
> So, the issue we see for CMD6 with R1, is a software problem that we
> should be able to fix.
> 
>>
>> With R1B, CMD complete and xfer complete both are generated after
>> response received + device busy (max timeout of 11s)
>> DATA timeout interrupt will be asserted incase if HW busy detection fails.
>>
>> With R1B we may see DATA Timeout if operation takes more than max busy
>> timeout of 11s.
> 
> Okay, I see.
> 
>>
>>> 2.
>>> Assuming my interpretation of the above is somewhat correct. Then you
>>> always need to set a busy timeout for R1/R1B responses in the
>>> controller. The maximum timeout seems to be 11s long. Obviously, this
>>> isn't enough for all cases, such as cache flushing and erase, for
>>> example. So, what can we do to support a longer timeouts than 11s?
>>> Would it be possible to disable the HW timeout, if the requested
>>> timeout is longer than 11s and use a SW timeout instead?
>>>
>>> Kind regards
>>> Uffe
>>
>> For erase long operations we have register bit to enable for infinite
>> busy wait mode where host controller would be monitoring until card is busy.
> 
> Alright, that sounds great!
> 
>>
>> But so far for emmc devices we used on our platforms, we haven't seen
>> cache flush taking more than 11s.
> 
> I understand that 11s is probably fine to use, for most cases.
> 
> However, it's not spec compliant, as for some operations there are
> simply no timeout specified. BKOPS, cache flush, sanitize are cases
> like this - and then 11s is definitely not sufficient.
> 
>>
>> Will get back on possibility of disabling HW timeout and using SW timeout..
> 
> Thanks!
> 
> I would like to get the regression fixed asap, but I also would like
> to avoid reverting patches, unless really necessary. May I propose the
> following two options.
> 
> 1. Find out why polling with ->card_busy() or CMD13, for a CMD6 with
> an R1 response doesn't work - and then fix that behaviour.
> 
> 2. Set the mmc->max_busy_timeout to zero for sdhci-tegra, which makes
> the core to always use R1B for CMD6 (and erase). This also means that
> when the cmd->busy_timeout becomes longer than 11s, sdhci-tegra must
> disable the HW busy timeout and just wait "forever".
> 
> If you decide for 2, you can add the software timeout support on top,
> but make that can be considered as a next step of an improvement,
> rather than needed as fix. Note that, I believe there are some support
> for software timeout already in the sdhci core, maybe you need to
> tweak it a bit for your case, I don't know.
> 

I was able to reproduce the issue on sdhci-omap with your patch applied.

In our case, the dat0 line never comes back up when trying to send a
CMD6 with R1. It needs an R1b to work properly. I also set
mmc->max_busy_timeout to 0 and that made it work as well.

I wanna try it out with other R1b commands like erase to see if it works
properly if the delay is actually very long.

Thanks,
Faiz



[Index of Archives]     [Linux RAID]     [Linux SCSI]     [Linux ATA RAID]     [IDE]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Device Mapper]

  Powered by Linux