From: James Smart <jsmart2021@xxxxxxxxx> To select the appropriate shost template, the driver is issuing a mailbox command to retrieve the wwn. Turns out the sending of the command precedes the reset of the function. On SLI-4 adapters, this is inconsequential as the mailbox command location is specified by dma via the BMBX register. However, on SLI-3 adapters, the location of the mailbox command submission area changes. When the function is first powered on or reset, the cmd is submitted via PCI bar memory. Later the driver changes the function config to use host memory and DMA. The request to start a mailbox command is the same, a simple doorbell write, regardless of submission area. So.. if there has not been a boot driver run against the adapter, the mailbox command works as defaults are ok. But, if the boot driver has configured the card and, and if no platform pci function/slot reset occurs as the os starts, the mailbox command will fail. The SLI-3 device will use the stale boot driver dma location. This can cause PCI eeh errors. Fix is to reset the sli-3 function before sending the mailbox command, thus synchronizing the function/driver on mailbox location. This issue was introduced by this patch: http://www.spinics.net/lists/linux-scsi/msg105908.html which is in the stable pools with commit id: 96418b5e2c8867da3279d877f5d1ffabfe460c3d This patch needs to be applied to the stable trees where ever the introducing patch exists. Signed-off-by: Dick Kennedy <dick.kennedy@xxxxxxxxxxxx> Signed-off-by: James Smart <james.smart@xxxxxxxxxxxx> Cc: stable@xxxxxxxxxxxxxxx --- drivers/scsi/lpfc/lpfc_crtn.h | 1 + drivers/scsi/lpfc/lpfc_init.c | 7 +++++++ drivers/scsi/lpfc/lpfc_sli.c | 2 +- 3 files changed, 9 insertions(+), 1 deletion(-) diff --git a/drivers/scsi/lpfc/lpfc_crtn.h b/drivers/scsi/lpfc/lpfc_crtn.h index 944b32c..62016d6 100644 --- a/drivers/scsi/lpfc/lpfc_crtn.h +++ b/drivers/scsi/lpfc/lpfc_crtn.h @@ -294,6 +294,7 @@ int lpfc_selective_reset(struct lpfc_hba *); void lpfc_reset_barrier(struct lpfc_hba *); int lpfc_sli_brdready(struct lpfc_hba *, uint32_t); int lpfc_sli_brdkill(struct lpfc_hba *); +int lpfc_sli_chipset_init(struct lpfc_hba *); int lpfc_sli_brdreset(struct lpfc_hba *); int lpfc_sli_brdrestart(struct lpfc_hba *); int lpfc_sli_hba_setup(struct lpfc_hba *); diff --git a/drivers/scsi/lpfc/lpfc_init.c b/drivers/scsi/lpfc/lpfc_init.c index 90ae354..e85f273 100644 --- a/drivers/scsi/lpfc/lpfc_init.c +++ b/drivers/scsi/lpfc/lpfc_init.c @@ -3602,6 +3602,13 @@ lpfc_get_wwpn(struct lpfc_hba *phba) LPFC_MBOXQ_t *mboxq; MAILBOX_t *mb; + if (phba->sli_rev < LPFC_SLI_REV4) { + /* Reset the port first */ + lpfc_sli_brdrestart(phba); + rc = lpfc_sli_chipset_init(phba); + if (rc) + return (uint64_t)-1; + } mboxq = (LPFC_MBOXQ_t *) mempool_alloc(phba->mbox_mem_pool, GFP_KERNEL); diff --git a/drivers/scsi/lpfc/lpfc_sli.c b/drivers/scsi/lpfc/lpfc_sli.c index cf19f49..22862b7 100644 --- a/drivers/scsi/lpfc/lpfc_sli.c +++ b/drivers/scsi/lpfc/lpfc_sli.c @@ -4446,7 +4446,7 @@ lpfc_sli_brdrestart(struct lpfc_hba *phba) * iteration, the function will restart the HBA again. The function returns * zero if HBA successfully restarted else returns negative error code. **/ -static int +int lpfc_sli_chipset_init(struct lpfc_hba *phba) { uint32_t status, i = 0; -- 2.9.3
