Re: [PATCH] bcache: make stripe_size configurable and persistent for hardware raid5/6

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, 25 Jun 2019, Coly Li wrote:
> On 2019/6/25 2:14 上午, Eric Wheeler wrote:
> > On Mon, 24 Jun 2019, Coly Li wrote:
> > 
> >> On 2019/6/23 7:16 上午, Eric Wheeler wrote:
> >>> From: Eric Wheeler <git@xxxxxxxxxxxxxxxxxx>
> >>>
> >>> While some drivers set queue_limits.io_opt (e.g., md raid5), there are
> >>> currently no SCSI/RAID controller drivers that do.  Previously stripe_size
> >>> and partial_stripes_expensive were read-only values and could not be
> >>> tuned by users (eg, for hardware RAID5/6).
> >>>
> >>> This patch enables users to save the optimal IO size via sysfs through
> >>> the backing device attributes stripe_size and partial_stripes_expensive
> >>> into the bcache superblock.
> >>>
> >>> Superblock changes are backwards-compatable:
> >>>
> >>> *  partial_stripes_expensive: One bit was used in the superblock flags field
> >>>
> >>> *  stripe_size: There are eight 64-bit "pad" fields for future use in
> >>>    the superblock which default to 0; from those, 32-bits are now used
> >>>    to save the stripe_size and load at device registration time.
> >>>
> >>> Signed-off-by: Eric Wheeler <bcache@xxxxxxxxxxxxxxxxxx>
> >>
> >> Hi Eric,
> >>
> >> In general I am OK with this patch. Since Peter comments lots of SCSI
> >> RAID devices reports a stripe width, could you please list the hardware
> >> raid devices which don't list stripe size ? Then we can make decision
> >> whether it is necessary to have such option enabled.
> > 
> > Perhaps they do not set stripe_width using io_opt? I did a grep to see if 
> > any of them did, but I didn't see them. How is stripe_width indicated by 
> > RAID controllers? 
> > 
> > If they do set io_opt, then at least my Areca 1883 does not set io_opt as 
> > of 4.19.x. I also have a LSI MegaRAID 3108 which does not report io_opt as 
> > of 4.1.x, but that is an older kernel so maybe support has been added 
> > since then.
> > 
> > Martin,
> > 
> > Where would stripe_width be configured in the SCSI drivers? Is it visible 
> > through sysfs or debugfs so I can check my hardware support without 
> > hacking debugging the kernel?
> > 
> >>
> >> Another point is, this patch changes struct cache_sb, it is no problem
> >> to change on-disk format. I plan to update the super block version soon,
> >> to store more configuration persistently into super block. stripe_size
> >> can be added to cache_sb with other on-disk changes.
> > 
> 
> Hi Eric,
> 
> > Maybe bumping version makes sense, but even if you do not, this is safe to 
> > use on systems without bumping the version because the values are unused 
> > and default to 0.
> 
> Yes, I understand you, it works as you suggested. I need to think how to
> organize all options in struct cache_sb, stripe_size will be arranged
> then. And I will ask help to you for reviewing the changes of on-disk
> format.

Hi Coli,

Just checking in, its been a while and I didn't see any more discussion on 
the topic:

This would benefit users with older RAID controllers using RAID-5/6 that 
don't set io_opt.

Even new new RAID controlers that _do_ provide `io_opt` still do _not_ 
indicate partial_stripes_expensive (which is an mdraid feature, but Martin 
please correct me if I'm wrong here).  Thus, all hardware RAID-5/6 users 
could benefit by manually flagging partial_stripes_expensive to get burst 
writes out of bcache that fit their stride width.

This patch probably needs rebased and documentation updated about io_opt, 
but here is the original patch with documentation for your reference:
	https://lkml.org/lkml/2019/6/22/298

What do you think?

-Eric

> 
> Thanks.
> 
> [snipped]
> 
> -- 
> 
> Coly Li
> 

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Index of Archives]     [Linux ARM Kernel]     [Linux Filesystem Development]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux OMAP]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux